Hi, Greg,
Unfortunately it's my laptop...
And here's smartctl information:
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.11.10-11-desktop] (SUSE RPM)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint M8 (AF)
Device Model: SAMSUNG HN-M101MBB
Serial Number: S2R8J9BB808817
LU WWN Device Id: 5 0024e9 205e8f61c
Firmware Version: 2AR10001
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Tue Jul 22 02:09:58 2014 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (13320) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 222) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail
Always - 2850
2 Throughput_Performance 0x0026 252 252 000 Old_age
Always - 0
3 Spin_Up_Time 0x0023 089 089 025 Pre-fail
Always - 3466
4 Start_Stop_Count 0x0032 098 098 000 Old_age
Always - 2161
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail
Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age
Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age
Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age
Always - 12867
10 Spin_Retry_Count 0x0032 252 252 051 Old_age
Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age
Always - 135
12 Power_Cycle_Count 0x0032 098 098 000 Old_age
Always - 2242
181 Program_Fail_Cnt_Total 0x0022 080 080 000 Old_age
Always - 452013413
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age
Always - 820
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age
Always - 0
194 Temperature_Celsius 0x0002 064 047 000 Old_age
Always - 36 (Min/Max 17/53)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age
Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age
Always - 0
197 Current_Pending_Sector 0x0032 252 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age
Always - 463
223 Load_Retry_Count 0x0032 100 100 000 Old_age
Always - 135
225 Load_Cycle_Count 0x0032 032 032 000 Old_age
Always - 691031
SMART Error Log Version: 1
Warning: ATA error count 19579 inconsistent with error log pointer 5
ATA Error Count: 19579 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 19579 occurred at disk power-on lifetime: 12857 hours (535 days
+ 17 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 84 ef 8f e3 Error: UNC 8 sectors at LBA = 0x038fef84 = 59764612
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 84 ef 8f e3 00 00:00:00.203 READ DMA
ef 10 02 00 00 00 a0 00 00:00:00.203 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:00:00.203 READ NATIVE MAX ADDRESS
EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.203 IDENTIFY DEVICE
ef 02 00 00 00 00 a0 00 00:00:00.203 SET FEATURES [Enable write cache]
Error 19578 occurred at disk power-on lifetime: 12725 hours (530 days + 5 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 84 ef 8f e3 Error: UNC 8 sectors at LBA = 0x038fef84 = 59764612
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 84 ef 8f e3 00 00:00:00.233 READ DMA
c8 00 08 84 ef 93 e0 00 00:00:00.233 READ DMA
c8 00 08 ac ef 93 e0 00 00:00:00.233 READ DMA
c8 00 08 cc ef 93 e0 00 00:00:00.233 READ DMA
c8 00 08 44 fa 93 e0 00 00:00:00.233 READ DMA
Error 19577 occurred at disk power-on lifetime: 12680 hours (528 days + 8 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 84 ef 8f e3 Error: UNC 8 sectors at LBA = 0x038fef84 = 59764612
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 84 ef 8f e3 00 00:00:35.602 READ DMA
25 00 10 15 ed 7a e0 00 00:00:35.602 READ DMA EXT
25 00 10 f5 9c 76 e0 00 00:00:35.602 READ DMA EXT
25 00 10 05 c7 7a e0 00 00:00:35.602 READ DMA EXT
25 00 10 f5 99 76 e0 00 00:00:35.602 READ DMA EXT
Error 19576 occurred at disk power-on lifetime: 12678 hours (528 days + 6 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 84 ef 8f e3 Error: UNC 8 sectors at LBA = 0x038fef84 = 59764612
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 84 ef 8f e3 00 00:00:29.969 READ DMA
c8 00 50 d4 d9 6f e0 00 00:00:29.969 READ DMA
c8 00 30 3c e0 6f e0 00 00:00:29.969 READ DMA
c8 00 88 b4 df 6f e0 00 00:00:29.969 READ DMA
c8 00 e8 14 d7 6f e0 00 00:00:29.969 READ DMA
Error 19575 occurred at disk power-on lifetime: 12678 hours (528 days + 6 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 c8 84 ef 8f e3 Error: UNC 200 sectors at LBA = 0x038fef84 = 59764612
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 f8 54 ef 8f e3 00 00:00:29.968 READ DMA
c8 00 08 4c ef 8f e3 00 00:00:29.968 READ DMA
c8 00 08 44 ef 8f e3 00 00:00:29.968 READ DMA
c8 00 20 44 ca 6f e0 00 00:00:29.968 READ DMA
c8 00 b0 b4 be ac e3 00 00:00:29.968 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has
ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
I at first didn't treat it as a hardware problem, I treated it as a
software problem because I can't believe all in a sudden my disk was
producting "end_request" for about 10 sectors in a very narrow time
window (in just a few minutes..) while I can still use my openSUSE
without any major problem (the hard shutdown will result a slow boot,
the suspend to ram/disk function still looks fine, and the daily
operation is good too)
Marguerite
On Tue, Jul 22, 2014 at 1:48 AM, Greg Freemyer
On Mon, Jul 21, 2014 at 12:02 PM, Larry Finger
wrote: If this system is a desktop, an easy thing to do is to replace the cable. On a laptop, that is generally not possible. In any case, I would be sure to have backups and a spare drive.
I agree with Larry in that my first diagnostic step when I see errors being reported is to replace the sata cable. It that fixes the problem, just toss the old cable.
If it doesn't is when I start diving into the "smartctl -a" data.
Greg -- Greg Freemyer -- To unsubscribe, e-mail: opensuse-kernel+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-kernel+owner@opensuse.org
-- To unsubscribe, e-mail: opensuse-kernel+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-kernel+owner@opensuse.org