Hallo! Vielleicht hat jemand einen Tip für mich bzgl. meines AVM-Controllers. Ich versuche via Asterisk eine Verbindung über CAPI nach außen aufzubauen, erhalte aber immer einen Protokoll 2 error - REASON=0x3302. Angesprochen wird die Karte von Asterisk via /dev/ttyI0 und /dev/ttyI1. Ich bin mir nun nicht sicher, ob ich da vergessen habe, etwas zu konfigurieren oder ob die Karte oder das Kabel defekt sind. Ich habe ein paar logauszüge eingefügt. delta*CLI> -- Executing Dial("SIP/andreas-1b5a", "CAPI/@144673:01757052847") in new stack -- data = @144673:01757052847 -- capi request omsn = @144673 == found capi with omsn = 144673 == CAPI Call CAPI[contr1/144673]/0 -- creating pipe for PLCI=-1 -- Called @144673:01757052847 -- CONNECT_CONF ID=002 #0x0004 LEN=0014 Controller/PLCI/NCCI = 0x101 Info = 0x0 -- CONNECT_CONF ID=002 #0x0004 LEN=0014 Controller/PLCI/NCCI = 0x101 Info = 0x0 == received CONNECT_CONF PLCI = 0x101 INFO = 0 -- DISCONNECT_IND ID=002 #0x0013 LEN=0014 Controller/PLCI/NCCI = 0x101 Reason = 0x3302 == DISCONNECT_IND PLCI=0x101 REASON=0x3302 -- CAPI Hangingup -- removed pipe for PLCI = 0x101 == No one is available to answer at this time -- Timeout on SIP/andreas-1b5a == CDR updated on SIP/andreas-1b5a -- Executing Hangup("SIP/andreas-1b5a", "") in new stack == Spawn extension (ausgehend, t, 1) exited non-zero on 'SIP/andreas-1b5a' Ein Ausschnit aus dmesg: ... Adding Swap: 511992k swap-space (priority 42) CAPI-driver Rev 1.1.4.1: loaded capifs: Rev 1.1.4.1 capi20: started up with major 68 kcapi: capi20 attached capi20: Rev 1.1.4.2: started up with major 68 (middleware+capifs) CSLIP: code copyright 1989 Regents of the University of California ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 loaded kcapi: capidrv attached kcapi: appl 1 up capidrv: Rev 1.1.4.1: loaded b1: revision 1.1.4.1 b1isa: revision 1.1.4.1 kcapi: driver b1isa attached kcapi: Controller 1: b1isa-340 attached b1isa: AVM B1 ISA at i/o 0x340, irq 7, revision 255 b1isa-340: card 1 "B1" ready. b1isa-340: card 1 Protocol: DSS1 b1isa-340: card 1 Linetype: point to multipoint b1isa-340: B1-card (3.11-03) now active kcapi: card 1 "b1isa-340" ready. kcapi: notify up contr 1 capidrv: controller 1 up capidrv-1: now up (2 B channels) capidrv-1: D2 trace enabled capi: controller 1 up via-rhine.c:v1.10-LK1.1.19 July-12-2003 Written by Donald Becker http://www.scyld.com/network/via-rhine.html PCI: Found IRQ 11 for device 00:11.0 PCI: Sharing IRQ 11 with 00:07.2 eth0: VIA VT6102 Rhine-II at 0xec00, 00:05:5d:a3:56:90, IRQ 11. eth0: MII PHY found at address 8, status 0x782d advertising 01e1 Link 0021. ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker http://www.scyld.com/network/ne2k-pci.html PCI: Found IRQ 12 for device 00:0f.0 eth1: RealTek RTL-8029 found at 0xe400, IRQ 12, 00:00:B4:9C:51:15. usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.275 $ time 13:14:03 Feb 15 2005 usb-uhci.c: High bandwidth mode enabled PCI: Found IRQ 11 for device 00:07.2 PCI: Sharing IRQ 11 with 00:11.0 usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver IPv6 v0.8 for NET4.0 IPv6 over IPv4 tunneling driver eth0: Promiscuous mode enabled. device eth0 entered promiscuous mode eth0: no IPv6 routers present eth1: no IPv6 routers present eth0: Promiscuous mode enabled. kcapi: appl 2 up kcapi: appl 2 releasing(1) kcapi: appl 2 down kcapi: appl 2 up capidrv-1: DISCONNECT_IND reason 0x3301 (Protocol error layer 1 (broken line or B-channel removed by signalling protocol)) for plci 0x101 capidrv-1: DISCONNECT_IND reason 0x3302 (Protocol error layer 2) for plci 0x101 capidrv-1: DISCONNECT_IND reason 0x3302 (Protocol error layer 2) for plci 0x101 kcapi: appl 2 releasing(1) kcapi: appl 2 down kcapi: appl 2 up Die Karte ist eine AVM-B1ISA Version 2.0. Ich habe auch schon die neueste Firmware probiert. Die capi.conf sieht so aus: # card file proto io irq mem cardnr options b1isa b1.t4 DSS1 0x340 7 - 1 Das ganze mit eine SuSE8.2 und selfrolled Kernel: Linux delta 2.4.29 #1 Tue Feb 15 11:53:57 CET 2005 i686 unknown delta:/etc # cat /proc/interrupts CPU0 0: 42949089 XT-PIC timer 1: 2 XT-PIC keyboard 2: 0 XT-PIC cascade 3: 2664590 XT-PIC serial 4: 54399 XT-PIC serial 5: 1060479 XT-PIC tmscsim 7: 50271 XT-PIC b1isa-340 8: 2 XT-PIC rtc 11: 494288 XT-PIC eth0, usb-uhci 12: 597643 XT-PIC eth1 14: 391842 XT-PIC ide0 15: 963894 XT-PIC ide1 NMI: 0 ERR: 0 delta:/etc # lsmod Module Size Used by Not tainted af_packet 11816 2 (autoclean) ipv6 146496 -1 (autoclean) joydev 6048 0 (unused) evdev 3936 0 (unused) input 3104 0 [joydev evdev] st 26672 0 (autoclean) (unused) sg 24036 0 (autoclean) usb-uhci 21124 0 (unused) usbcore 55968 1 [usb-uhci] ne2k-pci 4576 1 8390 5984 0 [ne2k-pci] via-rhine 11752 1 mii 2320 0 [via-rhine] crc32 2816 0 [8390 via-rhine] b1isa 3524 1 b1 17120 0 [b1isa] capidrv 24672 1 isdn 120288 0 [capidrv] slhc 4544 0 [isdn] capi 16960 4 capifs 3552 0 [capi] kernelcapi 29920 5 [b1isa capidrv capi] capiutil 22400 0 [capidrv kernelcapi] vfat 9276 0 (autoclean) fat 29816 0 (autoclean) [vfat] tmscsim 29600 2 ext3 62176 6 jbd 44116 6 [ext3] delta:/etc # cat /proc/capi/controllers/1 name b1isa-340 io 0x340 irq 7 type B1 ISA ver_driver 3.11-03 ver_cardtype B1 ver_serial 02081722 protocol DSS1 linetype point to multipoint cardname B1 Auf der Asteriskliste konnte mir keiner so recht helfen. Vielleicht hat hier jemand einen Tip? Danke! -- Andreas Meyer