Hallo,
ich habe schon viele verucht, und auch wertvolle Hinweise in dieser Liste
erhalten, aber ich erhalte immer wieder die gleiche Fehlermeldung:
Protokollfehler Ebene 2
Hardwarebeschreibung: Fritzcard classic mem:0x300, irq=10, (kein
Geräte-Konflikt)
vorsichtshalber habe ich alle anderen Karten entfernt. Nur noch
VGA-Adapter und Fritzcard classic.
Der Vollständigkeit hablber: Telefonanlage AGFEO AS192; Telekom-Ansschluss
point to Multipoint (kein Point to Point!)
Software: SuSE9.1, kernel 2.6.5, Online-update durchgeführt
Zusätzliche Hinweise:
Wenn ich in diesem Rechner die Fritzcard PCI verwende funktioniert alles!
Mit dem selben ISDN-Kabel und an der selben ISDN-Steckdose.
Wenn ich die Fritzcard classic in einem anderen Rechner mit Win2000
verwende funktioniert sie fehlerfrei.
Ich möchte aber diese Fritzcard classic in diesem Rechner (Pentium II,
350Mhz, 128MB) verwenden; es soll ein Internet-server und FAX-server
werden. HOFFENTLICH.
Ich habe einen Ausschnitt aus /var/log/messages beigefügt:
hier die Variante mit Fritzcard classic;
Der Verbindungsaufbau funktioniert fehlerfrei, es wird erst nach dem
eingestellten Timeout von 600sec. getrennt. ABER wenn ich einen
Internetbrowser (Opera, Konquerer) starte oder e-mails herunterlade wird
die Verbindung nach kurzer Zeit wegen Protokollfehler Ebene 2 getrennt.
Jun 22 08:35:19 linux kernel: klogd 1.4.1, log source = /proc/kmsg started.
Jun 22 08:35:19 linux kernel: Inspecting
/boot/System.map-2.6.5-7.75-default
Jun 22 08:35:20 linux kernel: Loaded 23738 symbols from
/boot/System.map-2.6.5-7.75-default.
Jun 22 08:35:20 linux kernel: Symbols match kernel version 2.6.5.
Jun 22 08:35:20 linux kernel: No module symbols loaded - kernel modules
not enabled.
Jun 22 08:35:20 linux kernel: CAPI Subsystem Rev 1.1.2.8
Jun 22 08:35:20 linux kernel: capifs: Rev 1.1.2.3
Jun 22 08:35:20 linux kernel: capi20: Rev 1.1.2.6: started up with major
68 (middleware+capifs)
Jun 22 08:35:20 linux kernel: CSLIP: code copyright 1989 Regents of the
University of California
Jun 22 08:35:20 linux kernel: ISDN subsystem Rev:
1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
Jun 22 08:35:20 linux kernel: capidrv: Rev 1.1.2.2: loaded
Jun 22 08:35:20 linux kernel: fcclassic: unsupported module, tainting
kernel.
Jun 22 08:35:20 linux kernel: fcclassic: module license 'Proprietary'
taints kernel.
Jun 22 08:35:20 linux kernel: fcclassic: AVM FRITZ!Card Classic driver,
revision 0.6.0
Jun 22 08:35:20 linux kernel: fcclassic: (fcclassic built on Jun 15 2004
at 20:36:05)
Jun 22 08:35:20 linux kernel: fcclassic: Driver 'fcclassic' attached to
stack. (152)
Jun 22 08:35:20 linux kernel: fcclassic: Stack version 3.11-02
Jun 22 08:35:20 linux kernel: kcapi: Controller 1: fcclassic-0300-10
attached
Jun 22 08:35:20 linux kernel: kcapi: card 1 "fcclassic-0300-10" ready.
Jun 22 08:35:20 linux kernel: capidrv: controller 1 up
Jun 22 08:35:20 linux kernel: capidrv-1: now up (2 B channels)
Jun 22 08:35:20 linux kernel: capidrv-1: D2 trace enabled
Jun 22 08:35:20 linux kernel: NET: Registered protocol family 10
Jun 22 08:35:20 linux kernel: IPv6 over IPv4 tunneling driver
Jun 22 08:35:20 linux kernel: ip6_tables: (C) 2000-2002 Netfilter core team
Jun 22 08:35:20 linux kernel: ip_tables: (C) 2000-2002 Netfilter core team
Jun 22 08:35:20 linux kernel: ip_conntrack version 2.1 (1023 buckets, 8184
max) - 300 bytes per conntrack
Jun 22 08:35:20 linux kernel: usbcore: registered new driver usbfs
Jun 22 08:35:20 linux kernel: usbcore: registered new driver hub
Jun 22 08:35:20 linux kernel: ippp, open, slot: 0, minor: 0, state: 0000
Jun 22 08:35:20 linux kernel: ippp_ccp: allocated reset data structure
c4889000
Jun 22 08:35:20 linux kernel: Linux agpgart interface v0.100 (c) Dave Jones
Jun 22 08:35:20 linux kernel: agpgart: Detected VIA Apollo
ProMedia/PLE133Ta chipset
Jun 22 08:35:20 linux kernel: agpgart: Maximum main memory to use for agp
memory: 94M
Jun 22 08:35:20 linux kernel: agpgart: AGP aperture is 64M @ 0xf8000000
Jun 22 08:35:20 linux SuSEfirewall2: Firewall rules successfully set in
QUICKMODE for device(s) " ippp1 ippp0" plus masquerading
Jun 22 08:35:24 linux sshd[2676]: Server listening on :: port 22.
Jun 22 08:35:24 linux kernel: powernow: This module only works with AMD K7
CPUs
Jun 22 08:35:24 linux rcpowersaved: CPU frequency scaling is not supported
by your processor.
Jun 22 08:35:24 linux rcpowersaved: enter 'POWERSAVE_CPUFREQD_MODULE=off'
in /etc/sysconfig/powersave/common to avoid this warning.
Jun 22 08:35:24 linux [powersaved][2693]: resmgr: server response code 200
Jun 22 08:35:27 linux kernel: parport0: PC-style at 0x378 [PCSPP]
Jun 22 08:35:27 linux kernel: parport0: irq 7 detected
Jun 22 08:35:27 linux kernel: lp0: using parport0 (polling).
Jun 22 08:35:27 linux kernel: drivers/usb/serial/usb-serial.c: USB Serial
support registered for Generic
Jun 22 08:35:27 linux kernel: usbcore: registered new driver usbserial
Jun 22 08:35:27 linux kernel: drivers/usb/serial/usb-serial.c: USB Serial
Driver core v2.0
Jun 22 08:35:33 linux /usr/sbin/cron[3052]: (CRON) STARTUP (fork ok)
Jun 22 08:35:35 linux kernel: Non-volatile memory driver v1.2
Jun 22 08:35:36 linux kernel: end_request: I/O error, dev fd0, sector 0
Jun 22 08:35:36 linux kernel: end_request: I/O error, dev fd0, sector 0
Jun 22 08:35:36 linux kernel: hdc: ATAPI 4X CD-ROM drive, 120kB Cache
Jun 22 08:35:36 linux kernel: Uniform CD-ROM driver Revision: 3.20
Jun 22 08:35:36 linux /etc/hotplug/block.agent[3082]: grep:
/sys/class/scsi_host/ide1/proc_name: No such file or directory
Jun 22 08:35:36 linux /etc/hotplug/block.agent[3082]: grep:
/sys/class/scsi_host/ide1/proc_name: No such file or directory
Jun 22 08:35:36 linux kernel: SCSI subsystem initialized
Jun 22 08:35:36 linux kernel: st: Version 20040318, fixed bufsize 32768,
s/g segs 256
Jun 22 08:35:36 linux /etc/hotplug/block.agent[3082]: new block device
/block/hdc
Jun 22 08:35:36 linux kernel: BIOS EDD facility v0.13 2004-Mar-09, 1
devices found
Jun 22 08:35:42 linux kernel: mtrr: no MTRR for ff000000,800000 found
Jun 22 08:35:42 linux kernel: mtrr: no MTRR for ff000000,400000 found
Jun 22 08:35:43 linux SuSEfirewall2: Firewall rules successfully set in
QUICKMODE for device(s) " ippp1 ippp0" plus masquerading
Jun 22 08:37:26 linux kdm: :0[3229]: pam_unix2: session started for user
root, service xdm
Jun 22 08:38:52 linux pppd[3563]: Plugin capiplugin.so loaded.
Jun 22 08:38:52 linux pppd[3563]: capiplugin: $Revision: 1.33 $
Jun 22 08:38:52 linux pppd[3563]: capiconn: 1.8
Jun 22 08:38:52 linux kernel: PPP generic driver version 2.4.2
Jun 22 08:38:52 linux pppd[3563]: pppd 2.4.2 started by root, uid 0
Jun 22 08:38:52 linux pppd[3563]: capiplugin: phase serialconn.
Jun 22 08:38:52 linux pppd[3563]: capiplugin: contr=1
Jun 22 08:38:52 linux pppd[3563]: controller 1: listen_change_state 0 -> 1
Jun 22 08:38:52 linux pppd[3563]: contr 1: listenconf Info=0x0000 (No
additional information) infomask=0x145 cipmask=0x0 capimask2=0x0
Jun 22 08:38:52 linux pppd[3563]: controller 1: listen_change_state 1 -> 0
Jun 22 08:38:52 linux pppd[3563]: plci_change_state:0x0 0 -> 1 event=1
Jun 22 08:38:52 linux pppd[3563]: capiplugin: dialing 194040 (hdlc)
Jun 22 08:38:52 linux pppd[3563]: plci_change_state:0x101 1 -> 2 event=3
Jun 22 08:38:52 linux isdnlog: Jun 22 08:38:52 * tei 64 calling 194040
with '' RING (Data)
Jun 22 08:38:59 linux isdnlog: Jun 22 08:38:59 tei 64 calling 194040 with
'' Time:Tue Jun 22 06:36:00 2004
Jun 22 08:38:59 linux pppd[3563]: plci_change_state:0x101 2 -> 3 event=6
Jun 22 08:38:59 linux pppd[3563]: ncci_change_state:0x101 0 -> 1 event=1
Jun 22 08:38:59 linux isdnlog: Jun 22 08:38:59 tei 64 calling 194040 with
'' CONNECT (Data)
Jun 22 08:38:59 linux pppd[3563]: ncci_change_state:0x10101 1 -> 3 event=3
Jun 22 08:38:59 linux pppd[3563]: ncci_change_state:0x10101 3 -> 4 event=7
Jun 22 08:38:59 linux pppd[3563]: ncci 0x10101 up
Jun 22 08:38:59 linux pppd[3563]: capiplugin: connected: "" -> "194040"
outgoing (pcli=0x101/ncci=0x10101)
Jun 22 08:38:59 linux pppd[3563]: capiplugin: using /dev/capi/0: "" ->
"194040" outgoing (pcli=0x101/ncci=0x10101)
Jun 22 08:38:59 linux kernel: capilib_new_ncci: kcapi: appl 2 ncci 0x10101
up
Jun 22 08:39:00 linux pppd[3563]: using channel 1
Jun 22 08:39:00 linux pppd[3563]: Using interface ppp0
Jun 22 08:39:00 linux pppd[3563]: Connect: ppp0 <--> /dev/capi/0
Jun 22 08:39:00 linux pppd[3563]: sent [LCP ConfReq id=0x1
<pcomp> <accomp>]
Jun 22 08:39:00 linux pppd[3563]: capiplugin: phase establish (was
serialconn).
Jun 22 08:39:00 linux pppd[3563]: rcvd [LCP ConfReq id=0x1
<auth chap MD5> <pcomp> <accomp>]
Jun 22 08:39:00 linux pppd[3563]: sent [LCP ConfAck id=0x1
<auth chap MD5> <pcomp> <accomp>]
Jun 22 08:39:00 linux pppd[3563]: rcvd [LCP ConfAck id=0x1
<pcomp> <accomp>]
Jun 22 08:39:00 linux pppd[3563]: sent [LCP EchoReq id=0x0
magic=0x456768a2]
Jun 22 08:39:00 linux pppd[3563]: capiplugin: phase authenticate (was
establish).
Jun 22 08:39:00 linux pppd[3563]: rcvd [CHAP Challenge id=0x2
<282ada85b0aa0a20f23a36ff1a345852>, name = "HiPer"]
Jun 22 08:39:00 linux pppd[3563]: sent [CHAP Response id=0x2
<3e5c74d3dd7ab4d2086b2f4b208ae7da>, name = "4229797000"]
Jun 22 08:39:00 linux pppd[3563]: rcvd [LCP EchoRep id=0x0
magic=0xf44df03e]
Jun 22 08:39:00 linux pppd[3563]: rcvd [CHAP Success id=0x2 "\000"]
Jun 22 08:39:00 linux pppd[3563]: CHAP authentication succeeded:
Jun 22 08:39:00 linux pppd[3563]: capiplugin: phase network (was
authenticate).
Jun 22 08:39:00 linux kernel: PPP BSD Compression module registered
Jun 22 08:39:00 linux kernel: PPP Deflate Compression module registered
Jun 22 08:39:00 linux pppd[3563]: sent [CCP ConfReq id=0x1
]
Jun 22 08:39:00 linux pppd[3563]: sent [IPCP ConfReq id=0x1 ]
Jun 22 08:39:00 linux pppd[3563]: rcvd [IPCP ConfReq id=0x3 ]
Jun 22 08:39:00 linux pppd[3563]: sent [IPCP ConfAck id=0x3 ]
Jun 22 08:39:00 linux pppd[3563]: rcvd [CCP ConfAck id=0x1 ]
Jun 22 08:39:00 linux pppd[3563]: rcvd [CCP ConfReq id=0x4 ]
Jun 22 08:39:00 linux pppd[3563]: sent [CCP ConfAck id=0x4 ]
Jun 22 08:39:00 linux pppd[3563]: Deflate (15) compression enabled
Jun 22 08:39:00 linux pppd[3563]: rcvd [IPCP ConfNak id=0x1 ]
Jun 22 08:39:00 linux pppd[3563]: sent [IPCP ConfReq id=0x2 ]
Jun 22 08:39:00 linux pppd[3563]: rcvd [IPCP ConfAck id=0x2 ]
Jun 22 08:39:00 linux pppd[3563]: local IP address 62.46.242.41
Jun 22 08:39:00 linux pppd[3563]: remote IP address 195.3.66.8
Jun 22 08:39:00 linux pppd[3563]: primary DNS address 195.3.96.68
Jun 22 08:39:00 linux pppd[3563]: secondary DNS address 195.3.96.67
Jun 22 08:39:00 linux pppd[3563]: capiplugin: phase running (was network).
Jun 22 08:39:00 linux pppd[3563]: Script /etc/ppp/ip-up started (pid 3595)
Jun 22 08:39:01 linux modify_resolvconf: Service pppd modified
/etc/resolv.conf. See info block in this file
Jun 22 08:39:03 linux SuSEfirewall2: Firewall rules successfully set in
QUICKMODE for device(s) " ippp1 ippp0" plus masquerading
Jun 22 08:39:03 linux pppd[3563]: Script /etc/ppp/ip-up finished (pid
3595), status = 0x0
Jun 22 08:39:47 linux pppd[3563]: ncci_change_state:0x10101 4 -> 7 event=10
Jun 22 08:39:47 linux kernel: Badness in local_bh_enable at
kernel/softirq.c:139
Jun 22 08:39:47 linux kernel: Call Trace:
Jun 22 08:39:47 linux kernel: [local_bh_enable+72/96]
local_bh_enable+0x48/0x60
Jun 22 08:39:47 linux kernel: [<c0122fb8>] local_bh_enable+0x48/0x60
Jun 22 08:39:47 linux kernel: [__crc_kobject_init+1878481/5840200]
ppp_sync_push+0x54/0x140 [ppp_synctty]
Jun 22 08:39:47 linux kernel: [<c90b5204>] ppp_sync_push+0x54/0x140
[ppp_synctty]
Jun 22 08:39:47 linux kernel: [__crc_kobject_init+1878745/5840200]
ppp_sync_wakeup+0x1c/0x50 [ppp_synctty]
Jun 22 08:39:47 linux kernel: [<c90b530c>] ppp_sync_wakeup+0x1c/0x50
[ppp_synctty]
Jun 22 08:39:47 linux kernel: [do_tty_hangup+775/880]
do_tty_hangup+0x307/0x370
Jun 22 08:39:47 linux kernel: [<c0203df7>] do_tty_hangup+0x307/0x370
Jun 22 08:39:47 linux kernel: [worker_thread+362/512]
worker_thread+0x16a/0x200
Jun 22 08:39:47 linux kernel: [<c012c49a>] worker_thread+0x16a/0x200
Jun 22 08:39:47 linux kernel: [do_tty_hangup+0/880]
do_tty_hangup+0x0/0x370
Jun 22 08:39:47 linux kernel: [<c0203af0>] do_tty_hangup+0x0/0x370
Jun 22 08:39:47 linux kernel: [default_wake_function+0/16]
default_wake_function+0x0/0x10
Jun 22 08:39:47 linux kernel: [<c011bee0>] default_wake_function+0x0/0x10
Jun 22 08:39:47 linux kernel: [default_wake_function+0/16]
default_wake_function+0x0/0x10
Jun 22 08:39:47 linux kernel: [<c011bee0>] default_wake_function+0x0/0x10
Jun 22 08:39:47 linux kernel: [worker_thread+0/512]
worker_thread+0x0/0x200
Jun 22 08:39:47 linux kernel: [<c012c330>] worker_thread+0x0/0x200
Jun 22 08:39:47 linux kernel: [kthread+169/209] kthread+0xa9/0xd1
Jun 22 08:39:47 linux kernel: [<c012f3d9>] kthread+0xa9/0xd1
Jun 22 08:39:47 linux kernel: [kthread+0/209] kthread+0x0/0xd1
Jun 22 08:39:47 linux kernel: [<c012f330>] kthread+0x0/0xd1
Jun 22 08:39:47 linux kernel: [kernel_thread_helper+5/16]
kernel_thread_helper+0x5/0x10
Jun 22 08:39:47 linux kernel: [<c0106005>] kernel_thread_helper+0x5/0x10
Jun 22 08:39:47 linux kernel:
Jun 22 08:39:47 linux kernel: kcapi: appl 2 ncci 0x10101 down
Jun 22 08:39:47 linux pppd[3563]: ncci_change_state:0x10101 7 -> 0 event=13
Jun 22 08:39:47 linux pppd[3563]: plci_change_state:0x101 3 -> 7 event=8
Jun 22 08:39:47 linux pppd[3563]: DISCONNECT_IND reason 0x3302 (Protocol
error layer 2) for plci 0x101
Jun 22 08:39:47 linux pppd[3563]: plci_change_state:0x101 7 -> 8 event=9
Jun 22 08:39:47 linux pppd[3563]: plci_change_state:0x101 8 -> 0 event=11
Jun 22 08:39:47 linux pppd[3563]: capiplugin: disconnect(remote): "" ->
"194040" outgoing (pcli=0x101/ncci=0x10101) 0x3302 (0x3301) - Protocol
error layer 2
Jun 22 08:39:47 linux pppd[3563]: Modem hangup
Jun 22 08:39:47 linux pppd[3563]: capiplugin: phase network (was running).
Jun 22 08:39:47 linux pppd[3563]: Script /etc/ppp/ip-down started (pid
3756)
Jun 22 08:39:47 linux pppd[3563]: capiplugin: phase establish (was
network).
Jun 22 08:39:47 linux pppd[3563]: capiplugin: phase dead (was establish).
Jun 22 08:39:47 linux pppd[3563]: controller 1: listen_change_state 0 -> 1
Jun 22 08:39:47 linux pppd[3563]: contr 1: listenconf Info=0x0000 (No
additional information) infomask=0x145 cipmask=0x0 capimask2=0x0
Jun 22 08:39:47 linux pppd[3563]: controller 1: listen_change_state 1 -> 0
Jun 22 08:39:47 linux pppd[3563]: Connection terminated.
Jun 22 08:39:47 linux pppd[3563]: Connect time 0.8 minutes.
Jun 22 08:39:47 linux pppd[3563]: Sent 3822 bytes, received 18419 bytes.
Jun 22 08:39:47 linux pppd[3563]: capiplugin: phase disconnect (was dead).
Jun 22 08:39:47 linux pppd[3563]: Waiting for 1 child processes...
Jun 22 08:39:47 linux pppd[3563]: script /etc/ppp/ip-down, pid 3756
Jun 22 08:39:48 linux modify_resolvconf: restored
/etc/resolv.conf.saved.by.pppd.ppp0 to /etc/resolv.conf
Jun 22 08:39:51 linux SuSEfirewall2: Firewall rules successfully set in
QUICKMODE for device(s) " ippp1 ippp0" plus masquerading
Jun 22 08:39:51 linux pppd[3563]: Script /etc/ppp/ip-down finished (pid
3756), status = 0x0
Jun 22 08:39:51 linux pppd[3563]: Connect time 0.8 minutes.
Jun 22 08:39:51 linux pppd[3563]: Sent 3822 bytes, received 18419 bytes.
Jun 22 08:39:51 linux pppd[3563]: controller 1: listen_change_state 0 -> 1
Jun 22 08:39:51 linux pppd[3563]: contr 1: listenconf Info=0x0000 (No
additional information) infomask=0x145 cipmask=0x0 capimask2=0x0
Jun 22 08:39:51 linux pppd[3563]: controller 1: listen_change_state 1 -> 0
Jun 22 08:39:51 linux pppd[3563]: capiplugin: exit
Jun 22 08:39:51 linux pppd[3563]: Exit.
Wenn die Verbindung abgebrochen wurde, kommt bei einem neuerlichen Versuch
mich einzuwählen nie mehr eine Verbindung zustande. Es wird immer mit
Protocol error layer 2 abgebrochen noch bevor eine Verbindung aufgebaut
werden konnte. Erst nach 'capiint stop' gefolgt von 'capiinit reload' kann
eine neue Verbindung aufgebaut werden - ja bis dann durch eine
Internetanwendung die Vebindung wieder getrennt wird.
Mit der Fritzcard pci läuft alles bestens:
Jun 22 21:48:36 linux syslogd 1.4.1: restart.
Jun 22 21:48:41 linux kernel: klogd 1.4.1, log source = /proc/kmsg started.
Jun 22 21:48:41 linux kernel: Inspecting
/boot/System.map-2.6.5-7.75-default
Jun 22 21:48:42 linux kernel: Loaded 23738 symbols from
/boot/System.map-2.6.5-7.75-default.
Jun 22 21:48:42 linux kernel: Symbols match kernel version 2.6.5.
Jun 22 21:48:42 linux kernel: No module symbols loaded - kernel modules
not enabled.
Jun 22 21:48:42 linux kernel: CAPI Subsystem Rev 1.1.2.8
Jun 22 21:48:42 linux kernel: capifs: Rev 1.1.2.3
Jun 22 21:48:42 linux kernel: capi20: Rev 1.1.2.6: started up with major
68 (middleware+capifs)
Jun 22 21:48:42 linux kernel: CSLIP: code copyright 1989 Regents of the
University of California
Jun 22 21:48:42 linux kernel: ISDN subsystem Rev:
1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
Jun 22 21:48:42 linux kernel: capidrv: Rev 1.1.2.2: loaded
Jun 22 21:48:42 linux kernel: fcpci: unsupported module, tainting kernel.
Jun 22 21:48:42 linux kernel: fcpci: module license 'Proprietary' taints
kernel.
Jun 22 21:48:42 linux kernel: fcpci: AVM FRITZ!Card PCI driver, revision
0.6.0
Jun 22 21:48:42 linux kernel: fcpci: (fcpci built on Jun 15 2004 at
20:35:46)
Jun 22 21:48:42 linux kernel: PCI: Assigned IRQ 9 for device 0000:00:0b.0
Jun 22 21:48:42 linux kernel: fcpci: AVM FRITZ!Card PCI found: port
0xde00, irq 9
Jun 22 21:48:42 linux kernel: fcpci: Loading...
Jun 22 21:48:42 linux kernel: fcpci: Driver 'fcpci' attached to stack.
(152)
Jun 22 21:48:42 linux kernel: fcpci: Stack version 3.11-02
Jun 22 21:48:42 linux kernel: kcapi: Controller 1: fcpci-de00-09 attached
Jun 22 21:48:42 linux kernel: kcapi: card 1 "fcpci-de00-09" ready.
Jun 22 21:48:42 linux kernel: fcpci: Loaded.
Jun 22 21:48:42 linux kernel: capidrv: controller 1 up
Jun 22 21:48:42 linux kernel: capidrv-1: now up (2 B channels)
Jun 22 21:48:42 linux kernel: capidrv-1: D2 trace enabled
Jun 22 21:48:42 linux kernel: NET: Registered protocol family 10
Jun 22 21:48:42 linux kernel: IPv6 over IPv4 tunneling driver
Jun 22 21:48:42 linux kernel: ip6_tables: (C) 2000-2002 Netfilter core team
Jun 22 21:48:42 linux kernel: ip_tables: (C) 2000-2002 Netfilter core team
Jun 22 21:48:42 linux kernel: ip_conntrack version 2.1 (1023 buckets, 8184
max) - 300 bytes per conntrack
Jun 22 21:48:42 linux kernel: usbcore: registered new driver usbfs
Jun 22 21:48:42 linux kernel: usbcore: registered new driver hub
Jun 22 21:48:42 linux kernel: ippp, open, slot: 0, minor: 0, state: 0000
Jun 22 21:48:42 linux kernel: ippp_ccp: allocated reset data structure
c5c1c000
Jun 22 21:48:42 linux kernel: Linux agpgart interface v0.100 (c) Dave Jones
Jun 22 21:48:42 linux kernel: agpgart: Detected VIA Apollo
ProMedia/PLE133Ta chipset
Jun 22 21:48:42 linux kernel: agpgart: Maximum main memory to use for agp
memory: 94M
Jun 22 21:48:42 linux kernel: agpgart: AGP aperture is 64M @ 0xf8000000
Jun 22 21:48:43 linux SuSEfirewall2: Firewall rules successfully set in
QUICKMODE for device(s) " ippp1 ippp0" plus masquerading
Jun 22 21:48:46 linux sshd[2689]: Server listening on :: port 22.
Jun 22 21:48:46 linux kernel: powernow: This module only works with AMD K7
CPUs
Jun 22 21:48:47 linux rcpowersaved: CPU frequency scaling is not supported
by your processor.
Jun 22 21:48:47 linux rcpowersaved: enter 'POWERSAVE_CPUFREQD_MODULE=off'
in /etc/sysconfig/powersave/common to avoid this warning.
Jun 22 21:48:47 linux [powersaved][2702]: resmgr: server response code 200
Jun 22 21:48:50 linux kernel: parport0: PC-style at 0x378 [PCSPP]
Jun 22 21:48:50 linux kernel: parport0: irq 7 detected
Jun 22 21:48:50 linux kernel: lp0: using parport0 (polling).
Jun 22 21:48:50 linux kernel: drivers/usb/serial/usb-serial.c: USB Serial
support registered for Generic
Jun 22 21:48:50 linux kernel: usbcore: registered new driver usbserial
Jun 22 21:48:50 linux kernel: drivers/usb/serial/usb-serial.c: USB Serial
Driver core v2.0
Jun 22 21:48:56 linux /usr/sbin/cron[3063]: (CRON) STARTUP (fork ok)
Jun 22 21:48:58 linux kernel: Non-volatile memory driver v1.2
Jun 22 21:48:58 linux kernel: end_request: I/O error, dev fd0, sector 0
Jun 22 21:48:58 linux kernel: end_request: I/O error, dev fd0, sector 0
Jun 22 21:48:59 linux kernel: hdc: ATAPI 4X CD-ROM drive, 120kB Cache
Jun 22 21:48:59 linux kernel: Uniform CD-ROM driver Revision: 3.20
Jun 22 21:48:59 linux /etc/hotplug/block.agent[3091]: grep:
/sys/class/scsi_host/ide1/proc_name: No such file or directory
Jun 22 21:48:59 linux /etc/hotplug/block.agent[3091]: grep:
/sys/class/scsi_host/ide1/proc_name: No such file or directory
Jun 22 21:48:59 linux kernel: SCSI subsystem initialized
Jun 22 21:48:59 linux /etc/hotplug/block.agent[3091]: new block device
/block/hdc
Jun 22 21:48:59 linux kernel: st: Version 20040318, fixed bufsize 32768,
s/g segs 256
Jun 22 21:48:59 linux kernel: BIOS EDD facility v0.13 2004-Mar-09, 1
devices found
Jun 22 21:49:05 linux kernel: mtrr: no MTRR for ff000000,800000 found
Jun 22 21:49:05 linux kernel: mtrr: no MTRR for ff000000,400000 found
Jun 22 21:49:06 linux SuSEfirewall2: Firewall rules successfully set in
QUICKMODE for device(s) " ippp1 ippp0" plus masquerading
Jun 22 21:49:18 linux kdm: :0[3242]: pam_unix2: session started for user
root, service xdm
Jun 22 21:50:49 linux pppd[3571]: Plugin capiplugin.so loaded.
Jun 22 21:50:49 linux pppd[3571]: capiplugin: $Revision: 1.33 $
Jun 22 21:50:49 linux pppd[3571]: capiconn: 1.8
Jun 22 21:50:49 linux kernel: PPP generic driver version 2.4.2
Jun 22 21:50:49 linux pppd[3571]: pppd 2.4.2 started by root, uid 0
Jun 22 21:50:49 linux pppd[3571]: capiplugin: phase serialconn.
Jun 22 21:50:49 linux pppd[3571]: capiplugin: contr=1
Jun 22 21:50:49 linux pppd[3571]: controller 1: listen_change_state 0 -> 1
Jun 22 21:50:49 linux pppd[3571]: contr 1: listenconf Info=0x0000 (No
additional information) infomask=0x145 cipmask=0x0 capimask2=0x0
Jun 22 21:50:49 linux pppd[3571]: controller 1: listen_change_state 1 -> 0
Jun 22 21:50:49 linux pppd[3571]: plci_change_state:0x0 0 -> 1 event=1
Jun 22 21:50:49 linux pppd[3571]: capiplugin: dialing 194040 (hdlc)
Jun 22 21:50:49 linux pppd[3571]: plci_change_state:0x101 1 -> 2 event=3
Jun 22 21:50:49 linux isdnlog: Jun 22 21:50:49 * tei 64 calling 194040
with '' RING (Data)
Jun 22 21:50:56 linux isdnlog: Jun 22 21:50:56 tei 64 calling 194040 with
'' Time:Tue Jun 22 21:48:00 2004
Jun 22 21:50:56 linux isdnlog: Jun 22 21:50:56 tei 64 calling 194040 with
'' CONNECT (Data)
Jun 22 21:50:56 linux pppd[3571]: plci_change_state:0x101 2 -> 3 event=6
Jun 22 21:50:56 linux pppd[3571]: ncci_change_state:0x101 0 -> 1 event=1
Jun 22 21:50:56 linux pppd[3571]: ncci_change_state:0x10101 1 -> 3 event=3
Jun 22 21:50:56 linux pppd[3571]: ncci_change_state:0x10101 3 -> 4 event=7
Jun 22 21:50:56 linux pppd[3571]: ncci 0x10101 up
Jun 22 21:50:56 linux pppd[3571]: capiplugin: connected: "" -> "194040"
outgoing (pcli=0x101/ncci=0x10101)
Jun 22 21:50:56 linux pppd[3571]: capiplugin: using /dev/capi/0: "" ->
"194040" outgoing (pcli=0x101/ncci=0x10101)
Jun 22 21:50:56 linux kernel: capilib_new_ncci: kcapi: appl 2 ncci 0x10101
up
Jun 22 21:50:57 linux pppd[3571]: using channel 1
Jun 22 21:50:57 linux pppd[3571]: Using interface ppp0
Jun 22 21:50:57 linux pppd[3571]: Connect: ppp0 <--> /dev/capi/0
Jun 22 21:50:57 linux pppd[3571]: sent [LCP ConfReq id=0x1
<pcomp> <accomp>]
Jun 22 21:50:57 linux pppd[3571]: capiplugin: phase establish (was
serialconn).
Jun 22 21:50:57 linux pppd[3571]: rcvd [LCP ConfReq id=0x1
<auth chap MD5> <pcomp> <accomp>]
Jun 22 21:50:57 linux pppd[3571]: sent [LCP ConfAck id=0x1
<auth chap MD5> <pcomp> <accomp>]
Jun 22 21:50:57 linux pppd[3571]: rcvd [LCP ConfAck id=0x1
<pcomp> <accomp>]
Jun 22 21:50:57 linux pppd[3571]: sent [LCP EchoReq id=0x0
magic=0xf1a2c571]
Jun 22 21:50:57 linux pppd[3571]: capiplugin: phase authenticate (was
establish).
Jun 22 21:50:57 linux pppd[3571]: rcvd [CHAP Challenge id=0x2
<0f34e9dcedc87b8b41699b6ed077abf5>, name = "HiPer"]
Jun 22 21:50:57 linux pppd[3571]: sent [CHAP Response id=0x2
<af0baf941b6a0e75b28388e4d32e635f>, name = "4229797000"]
Jun 22 21:50:57 linux pppd[3571]: rcvd [LCP EchoRep id=0x0
magic=0xf271a631]
Jun 22 21:50:57 linux pppd[3571]: rcvd [CHAP Success id=0x2 "\000"]
Jun 22 21:50:57 linux pppd[3571]: CHAP authentication succeeded:
Jun 22 21:50:57 linux pppd[3571]: capiplugin: phase network (was
authenticate).
Jun 22 21:50:57 linux kernel: PPP BSD Compression module registered
Jun 22 21:50:57 linux kernel: PPP Deflate Compression module registered
Jun 22 21:50:57 linux pppd[3571]: sent [CCP ConfReq id=0x1
]
Jun 22 21:50:57 linux pppd[3571]: sent [IPCP ConfReq id=0x1 ]
Jun 22 21:50:57 linux pppd[3571]: rcvd [IPCP ConfReq id=0x3 ]
Jun 22 21:50:57 linux pppd[3571]: sent [IPCP ConfAck id=0x3 ]
Jun 22 21:50:57 linux pppd[3571]: rcvd [CCP ConfAck id=0x1 ]
Jun 22 21:50:57 linux pppd[3571]: rcvd [CCP ConfReq id=0x4 ]
Jun 22 21:50:57 linux pppd[3571]: sent [CCP ConfAck id=0x4 ]
Jun 22 21:50:57 linux pppd[3571]: Deflate (15) compression enabled
Jun 22 21:50:57 linux pppd[3571]: rcvd [IPCP ConfNak id=0x1 ]
Jun 22 21:50:57 linux pppd[3571]: sent [IPCP ConfReq id=0x2 ]
Jun 22 21:50:57 linux pppd[3571]: rcvd [IPCP ConfAck id=0x2 ]
Jun 22 21:50:57 linux pppd[3571]: local IP address 62.46.243.119
Jun 22 21:50:57 linux pppd[3571]: remote IP address 195.3.66.9
Jun 22 21:50:57 linux pppd[3571]: primary DNS address 195.3.96.68
Jun 22 21:50:57 linux pppd[3571]: secondary DNS address 195.3.96.67
Jun 22 21:50:57 linux pppd[3571]: capiplugin: phase running (was network).
Jun 22 21:50:57 linux pppd[3571]: Script /etc/ppp/ip-up started (pid 3603)
Jun 22 21:50:58 linux modify_resolvconf: Service pppd modified
/etc/resolv.conf. See info block in this file
Jun 22 21:51:00 linux SuSEfirewall2: Firewall rules successfully set in
QUICKMODE for device(s) " ippp1 ippp0" plus masquerading
Jun 22 21:51:00 linux pppd[3571]: Script /etc/ppp/ip-up finished (pid
3603), status = 0x0
Jun 22 21:51:33 linux pppd[3571]: rcvd [Compressed data] 00 22 82 34 c4 1d
c1 0d ...
Jun 22 21:51:33 linux pppd[3571]: sent [CCP ResetReq id=0x2]
Jun 22 21:51:33 linux pppd[3571]: rcvd [Compressed data] 00 23 d2 e5 b7 3e
86 55 ...
Jun 22 21:51:33 linux pppd[3571]: rcvd [Compressed data] 00 24 9c 9c bf 0a
c2 30 ...
Jun 22 21:51:34 linux pppd[3571]: rcvd [Compressed data] 00 25 94 9d cd 6a
c3 30 ...
Jun 22 21:51:34 linux pppd[3571]: rcvd [Compressed data] 00 26 82 6c 3f 94
06 ef ...
Jun 22 21:51:34 linux pppd[3571]: rcvd [Compressed data] 00 27 94 5c cd 4e
c2 40 ...
Jun 22 21:51:34 linux pppd[3571]: rcvd [Compressed data] 00 28 a4 5c 4b 4e
c3 30 ...
Jun 22 21:51:34 linux pppd[3571]: rcvd [Compressed data] 00 29 52 74 65 60
d6 9a ...
Jun 22 21:51:34 linux pppd[3571]: rcvd [CCP ResetAck id=0x2]
Jun 22 21:51:34 linux pppd[3571]: rcvd [Compressed data] 00 2a 9c 9c 41 0e
82 30 ...
Jun 22 21:51:34 linux pppd[3571]: sent [CCP ResetReq id=0x3]
Jun 22 21:51:34 linux pppd[3571]: rcvd [Compressed data] 00 2b 02 b5 83 9e
b0 ba ...
Jun 22 21:51:34 linux pppd[3571]: rcvd [CCP ResetAck id=0x3]
Jun 22 21:51:37 linux pppd[3571]: rcvd [Compressed data] 00 2f 02 7b 37 32
1b a8 ...
Jun 22 21:51:37 linux pppd[3571]: sent [CCP ResetReq id=0x4]
Jun 22 21:51:37 linux pppd[3571]: rcvd [Compressed data] 00 30 d2 15 28 f5
a2 b3 ...
Jun 22 21:51:37 linux pppd[3571]: rcvd [Compressed data] 00 31 02 fb 37 32
17 e4 ...
Jun 22 21:51:37 linux pppd[3571]: rcvd [CCP ResetAck id=0x4]
selbst wenn der ISP nach 8 Stunden die Leitung trennt wird mit 'persist'
automatisch wieder eingewählt und alles läuft weiter.
Woran liegt es, dass ich das mit der Fritzcard classic nicht schafffe?
Wer weiss mir hier einen RAT?
Für jede Hilfe bin ich dankbar.
Mit freundlichen Grüssen
Siegfried
--
Using Opera's revolutionary e-mail client: http://www.opera.com/m2/
