Hi, On Sun, 9 Aug 2009, Patrick Shanahan wrote:
* Patrick Shanahan
[08-09-09 21:56]: * Eberhard Moenkeberg
[08-09-09 21:44]: * Eberhard Moenkeberg
[08-09-09 20:26]:
After the lines from detecting your graphics card, you will find some lines from detecting your monitor. Your monitor is telling his capabilities by clear resolution and frequency numbers.
Just correct your "Monitor" Section with these data, and maybe the "Modes" section too.
I will check. I'm out of X right now and an update of xorg.* is ongoing. I will test before returning to X.
Ok, it doesn't like the nvidia driver, I guess.
X.Org X Server 1.6.3 Release Date: 2009-7-31 X Protocol Version 11, Revision 0 Build Operating System: openSUSE SUSE LINUX Current Operating System: Linux wahoo 2.6.31-rc5-git3-2-default #1 SMP 2009-08-06 23:25:57 +0200 x86_64 Build Date: 09 August 2009 11:06:04PM
Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Sun Aug 9 22:25:45 2009 (++) Using config file: "./xorg.conf.new" (EE) module ABI major version (1) doesn't match the server's version (2) (EE) Failed to load module "vnc" (module requirement mismatch, 0) (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found)
/var/log/Xorg.0.log and xorg.conf.new are available: http://wahoo.no-ip.org/~pat/Xorg.0.log http://wahoo.no-ip.org/~pat/xorg.conf.new
(--) NV: Found NVIDIA GeForce 7300 GS at 05@00:00:0 ... (II) NV(0): Probing for analog device on output A... (--) NV(0): ...found one (II) NV(0): Probing for analog device on output B... (--) NV(0): ...found one (II) NV(0): Probing for EDID on I2C bus A... (II) NV(0): I2C device "DDC:E-EDID segment register" registered at address 0x60. (II) NV(0): I2C device "DDC:ddc2" registered at address 0xA0. (--) NV(0): DDC detected a DFP: (II) NV(0): Manufacturer: SAM Model: 467 Serial#: 1129132596 (II) NV(0): Year: 2009 Week: 1 (II) NV(0): EDID Version: 1.3 (II) NV(0): Digital Display Input (II) NV(0): Max Image Size [cm]: horiz.: 52 vert.: 32 (II) NV(0): Gamma: 2.20 (II) NV(0): DPMS capabilities: Off (II) NV(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 (II) NV(0): First detailed timing is preferred mode (II) NV(0): redX: 0.650 redY: 0.337 greenX: 0.296 greenY: 0.604 (II) NV(0): blueX: 0.147 blueY: 0.074 whiteX: 0.312 whiteY: 0.329 ... (II) NV(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0 (II) NV(0): v_active: 1200 v_sync: 1203 v_sync_end 1209 v_blanking: 1235 v_border: 0 (II) NV(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 81 kHz, PixClock max 170 MHz (II) NV(0): Monitor name: SyncMaster With these infos, you can build an appropriate mode line: Section "Modes" Identifier "Modes[0]" Modeline "1920x1200" 154 1920 1968 2000 2080 1200 1203 1209 1235 EndSection which is indeed already in the log: (II) NV(0): Printing DDC gathered Modelines: (II) NV(0): Modeline "1920x1200"x0.0 154.00 1920 1968 2000 2080 1200 1203 1209 1235 +hsync -vsync (74.0 kHz) and a monitor section: Section "Monitor" DisplaySize 520 320 HorizSync 30-81 Identifier "Monitor[0]" ModelName "SyncMaster" VertRefresh 56-75 UseModes "Modes[0]" EndSection Viele Gruesse Eberhard Moenkeberg (emoenke@gwdg.de, em@kki.org) -- Eberhard Moenkeberg Arbeitsgruppe IT-Infrastruktur E-Mail: emoenke@gwdg.de Tel.: +49 (0)551 201-1551 ------------------------------------------------------------------------- Gesellschaft fuer wissenschaftliche Datenverarbeitung mbH Goettingen (GWDG) Am Fassberg 11, 37077 Goettingen URL: http://www.gwdg.de E-Mail: gwdg@gwdg.de Tel.: +49 (0)551 201-1510 Fax: +49 (0)551 201-2150 Geschaeftsfuehrer: Prof. Dr. Bernhard Neumair Aufsichtsratsvorsitzender: Dipl.-Kfm. Markus Hoppe Sitz der Gesellschaft: Goettingen Registergericht: Goettingen Handelsregister-Nr. B 598 ------------------------------------------------------------------------- -- To unsubscribe, e-mail: opensuse-factory+unsubscribe@opensuse.org For additional commands, e-mail: opensuse-factory+help@opensuse.org