Bueno, pues ya tengo el wireless funcionando... Parece que el paquete que me ha estado dando el coñazo es el acer_acpi. Vuelto a instalar, esta vez la versión 0.9.x última estable: make /make install (con las kernel-sources instaladas claro). modprobe acer_acpi (sin errores) luego echo 1 > /proc/acpi/acer/wireless ya tengo la luz funcionando y se activa sólo LISTO. Lo aclaro por si a alguien más le pasa esto, que pruebe a reinstalar el módulo acer_acpi sin quitar el bcm43xx ni nada (no hace falta) que seguramente le pase como a mi, un problema absurdo. ------------------------------------------------------ El Lunes, 3 de Diciembre de 2007 14:49, Harmless escribió:
Bueno, parece que he conseguido algo más. Después de seguir todos los pasos, mirar las listas de correo que me habéis pasado hasta aburrirme, he conseguido que al poner iwconfig salga esto:
eth0 IEEE 802.11b/g ESSID:off/any Nickname:"Broadcom 4318" Mode Managed Frecuency=2484 GHz Access Point: Invalid Bit Rate=1 Mb/s Tx-Power=19 dBm etc etc etc
Como veis el punto de acceso es inválido cuando debería aparecer la mac.
¿Cómo puedo cambiar esto??????
El Jueves, 29 de Noviembre de 2007 14:02, Juan Erbes escribió:
Justo estbe mirando el link de Camaleon, y aparece un detalle de lo que te habia pasado antes, como alternativa al ndiswrapper: 1. You need to check if the bcm43xx-fwcutter package is installed through: Yast > Software > Software Installation and search for bcm43xx-fwcutter
2. Find the windows driver for your wireless chip. An example windows driver was titled bcmwl5.sys Also note if you can't find yours try doing a google search for wl_apsta.o (SUSE worked with both the orginal windows driver and the wl_apsta.o at the time of this WIKI post). Put the driver file on your desktop in SUSE.
3. Start the shell console (Kmenu >System > Terminal Program > Terminal) and login as root with the command:
sux -
and type in the root password
Extract your firmware files from your wireless chip and store them in the firmware file by typing in the following. (Note: Swap out the name of your driver accordingly...in this example it is dirver.sty):
bcm43xx-fwcutter -w /lib/firmware ~/Desktop/driver.sty
4. Another way to install the firmware is using the install script included in the bcm43xx-fwcutter package. You need to have a working internet connection for this as it is attempted to download driver.sty, next the firmware is extracted and stored in /lib/firmware.
install_bcm43xx_firmware
5. Now that the firmware is ready for the driver to use, load the module by typing the following:
modprobe bcm43xx
6. Reboot and now you can configure your WLAN card through YAST > Network devices > Network card [edit]
El 28/11/07, Harmless
escribió: Nanai de la china.
Gracias de todas formas.
Si se ocurre algo nuevo que pueda hacer, escribídlo, que por probar, me resisto a estar con la 10.1 con Wifi sin problemas y ahora con la 10.2 / 10.3 sin la red inalámbrica.
Salu2
--------------------------------------------------------------------- Para dar de baja la suscripcin, mande un mensaje a: opensuse-es+unsubscribe@opensuse.org Para obtener el resto de direcciones-comando, mande un mensaje a: opensuse-es+help@opensuse.org
Para dar de baja la suscripción, mande un mensaje a: opensuse-es+unsubscribe@opensuse.org Para obtener el resto de direcciones-comando, mande un mensaje a: opensuse-es+help@opensuse.org