hat jemand zufaellig ein ELSA Microlink 56k basic und arbeitet auch noch mit hylafax ? Ich habe damit Probleme, wenn Fax-Class 2.0 eingestellt ist: 1.) den Befehl AT+FAP kennt das modem nicht 2.) bei aelteren Faxgeraeten kommt bei Senden folgende Fehlermeldung: Mar 21 21:04:09.65: [ 635]: <-- [10:ATDT14124\r] Mar 21 21:04:25.10: [ 635]: --> [4:+FCO] Mar 21 21:04:26.98: [ 635]: --> [27:+FCI:" +49 2603 14124"] Mar 21 21:04:26.98: [ 635]: REMOTE CSI "+49 2603 14124" Mar 21 21:04:26.98: [ 635]: --> [20:+FIS:1,3,0,2,0,0,0,4] Mar 21 21:04:26.98: [ 635]: --> [2:OK] Mar 21 21:04:26.98: [ 635]: REMOTE best rate 9600 bit/s Mar 21 21:04:26.98: [ 635]: REMOTE max page width 1728 pixels in 215 mm Mar 21 21:04:26.98: [ 635]: REMOTE max unlimited page length Mar 21 21:04:26.98: [ 635]: REMOTE best vres 7.7 line/mm Mar 21 21:04:26.98: [ 635]: REMOTE best format 1-D MR Mar 21 21:04:26.98: [ 635]: REMOTE best 20 ms, 10 ms/scanline Mar 21 21:04:26.98: [ 635]: USE 9600 bit/s Mar 21 21:04:26.98: [ 635]: USE 20 ms, 10 ms/scanline Mar 21 21:04:26.98: [ 635]: SEND file "docq/doc25.cover;00" Mar 21 21:04:27.51: [ 635]: USE page width 1728 pixels in 215 mm Mar 21 21:04:27.51: [ 635]: USE unlimited page length Mar 21 21:04:27.51: [ 635]: USE 3.85 line/mm Mar 21 21:04:27.51: [ 635]: USE 1-D MR Mar 21 21:04:27.51: [ 635]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r] Mar 21 21:04:27.64: [ 635]: --> [2:OK] Mar 21 21:04:27.64: [ 635]: <-- [7:AT+FDT\r] Mar 21 21:04:33.33: [ 635]: --> [20:+FCS:0,3,0,2,0,0,0,5] Mar 21 21:04:33.63: [ 635]: --> [7:CONNECT] Mar 21 21:04:33.63: [ 635]: SEND begin page Mar 21 21:04:37.68: [ 635]: SENT 7906 bytes of data Mar 21 21:04:37.68: [ 635]: SEND 1D RTC Mar 21 21:04:37.68: [ 635]: SEND end page Mar 21 21:04:37.68: [ 635]: SEND send MPS (more pages, same document) Mar 21 21:05:29.96: [ 635]: --> [7:+FHS:43] Mar 21 21:05:29.96: [ 635]: REMOTE HANGUP: DTE to DCE data underflow (code 43) Mar 21 21:05:29.96: [ 635]: SEND: DTE to DCE data underflow; Giving up after 3 attempts to send same page "docq/doc25.cover;00", dirnum 0 Mar 21 21:05:29.96: [ 635]: <-- [5:ATH0\r] Mar 21 21:05:29.96: [ 635]: --> [2:OK] Mar 21 21:05:29.96: [ 635]: MODEM set DTR OFF Mar 21 21:05:29.97: [ 635]: SESSION END Hat jemand ne Idee ? Lt. Doku soll Class 2.0 laufen ! Bye Andre *** Andre Best * 56337 Arzbach * Fax: 089 2443 15498 *** --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com