Mailinglist Archive: opensuse-bugs (8956 mails)

< Previous Next >
[Bug 216089] New: identifying devices on secondary ATA port times out 3 times on Fujitsu Siemens E-4010 notebook
  • From: bugzilla_noreply@xxxxxxxxxx
  • Date: Sat, 28 Oct 2006 13:49:41 -0600 (MDT)
  • Message-id: <bug-216089-21960@xxxxxxxxxxxxxxxxxxxxxxxxx/>
https://bugzilla.novell.com/show_bug.cgi?id=216089

Summary: identifying devices on secondary ATA port times out 3
times on Fujitsu Siemens E-4010 notebook
Product: openSUSE 10.2
Version: Beta 1
Platform: i686
OS/Version: Other
Status: NEW
Severity: Normal
Priority: P5 - None
Component: Kernel
AssignedTo: kernel-maintainers@xxxxxxxxxxxxxxxxxxxxxx
ReportedBy: jsj@xxxxxxxxxxxxxx
QAContact: qa@xxxxxxx


During boot on ATA controller initialisation identification of secondary master
DVD-ROM/CD-RW device failes three times.

boot.msg shows:
<7>libata version 2.00 loaded.
<7>ata_piix 0000:00:1f.1: version 2.00ac6
<4>PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
<4>ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
<6>ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
<7>PCI: Setting latency timer of device 0000:00:1f.1 to 64
<6>ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0x1810 irq 14
<6>ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
<6>scsi0 : ata_piix
<6>Time: acpi_pm clocksource has been installed.
<6>input: PS/2 Mouse as /class/input/input2
<6>input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
<6>ata1.00: ATA-5, max UDMA/100, 39070080 sectors: LBA
<6>ata1.00: ata1: dev 0 multi count 16
<6>ata1.00: configured for UDMA/100
<6>scsi1 : ata_piix
<6>ata2.00: ATAPI, max UDMA/33
<4>ata2.01: qc timeout (cmd 0xa1)
<4>ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
<4>ata2: failed to recover some devices, retrying in 5 secs
<4>ata2.01: qc timeout (cmd 0xa1)
<4>ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
<4>ata2: failed to recover some devices, retrying in 5 secs
<4>ata2.01: qc timeout (cmd 0xa1)
<4>ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
<4>ata2: failed to recover some devices, retrying in 5 secs
<6>ata2.00: configured for UDMA/33
<5> Vendor: ATA Model: IC25N020ATCS04-0 Rev: CA2O
<5> Type: Direct-Access ANSI SCSI revision: 05
<5>SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
<5>sda: Write Protect is off
<7>sda: Mode Sense: 00 3a 00 00
<5>SCSI device sda: drive cache: write back
<5>SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
<5>sda: Write Protect is off
<7>sda: Mode Sense: 00 3a 00 00
<5>SCSI device sda: drive cache: write back
<6> sda: sda1 sda2
<5>sd 0:0:0:0: Attached scsi disk sda
<5> Vendor: MATSHITA Model: UJDA750FDVD/CDRW Rev: 1.21
<5> Type: CD-ROM ANSI SCSI revision: 05
<6>device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
dm-devel@xxxxxxxxxx
<6>BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>scsi 1:0:0:0: Attached scsi generic sg1 type 5
<4>sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
<6>Uniform CD-ROM driver Revision: 3.20
<7>sr 1:0:0:0: Attached scsi CD-ROM sr0

The drive is finally started up, but boot process is delay for about 30s.


--
Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.

< Previous Next >
Follow Ups