May 2017 - openSUSE ARM - openSUSE Mailing Lists

[opensuse-arm] JeOS-2017-03-13 image for RPi 1 installs OK, Grub fails on reboot
by Alex Armstrong 14 Nov '17

14 Nov '17

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Greetings, I was testing: openSUSE-Tumbleweed-ARM-JeOS-raspberrypi.armv6l-2017.03.13-Build1.8.raw.xz from: http://download.opensuse.org/repositories/devel:/ARM:/Factory:/Contrib:/Ras… On RaspberryPi 1 Model B It installs fine - expands the file system, creates the dracut based init and boots to a usable system. But when I reboot, grub fails with: error: attempt to read or write outside of partition. and drops me to the grub rescue system. Poking around the rescue system, I've found that I can see 4 partitions, one which is ext2 and has the normal Linux files. From here, most of the recovery guides say to set the root and prefix variables and then load the normal module. I can execute the commands: set root=(hd0,gpt2) set prefix=(hd0,gpt2)/boot/grub2 and list the files in the various directories - normal.mod exists in /boot/grub2/arm-efi/ - but when I try: insmod normal I still get the error: attempt to read or write outside of partition. Somewhat interestingly, if I miss-type the prefix (say; /boot/grub) the error changes to a "file not found" one. I was hoping someone might have some ideas about what to try next. - -Alex -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) iEYEARECAAYFAljUJnYACgkQYZYc2javKOllFQCeNiB6oZYpnKxgmKsbdUtcQNrO mOIAoJBXe8913EIzBfD04P/PqfPjFv9e =ZZC3 -----END PGP SIGNATURE----- -- To unsubscribe, e-mail: opensuse-arm+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-arm+owner(a)opensuse.org

3 9

[opensuse-arm] openSUSE-Leap42.2-ARM-JeOS-raspberrypi2 and RPi3
by Matwey V. Kornilov 15 Jun '17

15 Jun '17

Hello, Could somebody please tell me whether raspberrypi2 image supposed to work on raspberrypi3 in armv7 mode? I've just tried but I don't see anything on serial console, even u-boot messages. Is it the image broken? I don't have raspberrypi2 to test. -- To unsubscribe, e-mail: opensuse-arm+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-arm+owner(a)opensuse.org

6 11

[opensuse-arm] openSUSE for Khadas VIM
by Oleg 17 May '17

17 May '17

Hi. I'm trying to run openSUSE on Khadas VIM. Which settings\variables u-boot you need to install to transfer control after the start of u-boot to openSUSE ? -- To unsubscribe, e-mail: opensuse-arm+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-arm+owner(a)opensuse.org

3 5

[opensuse-arm] Firefly RK3399 board
by Bill Merriam 15 May '17

15 May '17

Has anyone had a chance to try this board? With 4GB of RAM on it and a couple of SSDs, it might make a pretty good server/build server/desktop/media center or something. http://wiki.t-firefly.com/index.php/Firefly-RK3399/en I notice Andreas has some firmware for this processor. Can I put that together with our AARCH64 root file system and make a bootable system? Would it help things along if I gifted one of these boards to Andreas? Bill -- To unsubscribe, e-mail: opensuse-arm+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-arm+owner(a)opensuse.org

3 3

[opensuse-arm] openSUSEfying Chromebooks
by Andrew Wafaa 12 May '17

12 May '17

Hi, Could someone remind me what steps are needed to get a native openSUSE kernel up on chromebooks and as such enable creating a full installable image (similar to what was done to the original Samsung Chromebook). I'd like to create an image for the Samsung Plus (aarch64), and as it uses 4.4 I thought it would be easier to use the Leap kernel, would this be correct or should I just use the Tumbleweed one? Ideally I'd like to have this before oSC but let's see. Thanks, Andy -- To unsubscribe, e-mail: opensuse-arm+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-arm+owner(a)opensuse.org

2 1

[opensuse-arm] PiXtend
by Roger Oberholtzer 10 May '17

10 May '17

Has anyone tried PiXtend Raspberry cards? With openSUSE? http://www.pixtend.de http://www.pixtend.de/pixtend/downloads/downloads-v1-3-english/ -- Roger Oberholtzer -- To unsubscribe, e-mail: opensuse-arm+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-arm+owner(a)opensuse.org

3 2

[opensuse-arm] MAC address on Raspberry PI 3
by Roger Oberholtzer 02 May '17

02 May '17

I have just updated my previously working RI 3 to the latest kernel for openSUSE 42.2 It seems that the device now generates a unique MAC address on the wired Ethernet connection each time it is powered on. Could this happen? If so, how can I change it back to use a fixed MAC address? -- Roger Oberholtzer -- To unsubscribe, e-mail: opensuse-arm+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-arm+owner(a)opensuse.org

10 39

[opensuse-arm] New package: meson-tools
by Andreas Färber 02 May '17

02 May '17

Hello, I have written, packaged and now submitted meson-tools v0.1: https://build.opensuse.org/request/show/492296 Inspired by the sunxi-tools package for Allwinner SoCs, which is already in Factory, this one is a set of tools for Amlogic SoCs - currently for Amlogic S905 aka Meson GXBaby. The main tool is amlbootsig, which is a replacement for Amlogic's x86-only proprietary tool aml_encrypt_gxb. amlbootsig has been successfully used to build the JeOS-odroidc2 aarch64 Tumbleweed images. In order to build future official images in openSUSE:Factory:ARM, this tool needs to go into Factory. Other tools are for analyzing (amlbootinfo) and updating (unamlbootsig) bootloader binaries. See the README.md for more details on usage and known limitations. Thanks again to those that contributed to or supported the creation of these tools. Have a lot of fun, Andreas -- SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB 21284 (AG Nürnberg) -- To unsubscribe, e-mail: opensuse-arm+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-arm+owner(a)opensuse.org

3 3

[opensuse-arm] DT overlays (was: Drivers for display for rpi3)
by Andreas Färber 02 May '17

02 May '17

Hi Tony, Am 24.04.2017 um 19:19 schrieb Tony Su: > Hi, > I'm looking for the referenced Wiki with links to dtb overlays, can't > find it. > > For that matter, I can't find the specific github repo (Is the Wiki > associated with the github project or some other Wiki?) > > Looking around, I can only find the following HCL page that lists > supported HATs which is something I haven't noticed before. > https://en.opensuse.org/Category:Raspberry_Pi_40-pin_connector Look at the ArPi600 link in that category, for instance. For Chistera Pi and TLV493D there are overlay files too, but no links in the Wiki yet. The Arduino Shield, MikroBus and XBee categories should also have some. The commands can either be typed manually or placed in a boot.script that then needs to be turned into boot.scr via mkimage (u-boot-tools) and placed into the first partition (i.e., /boot/efi if it exists, /boot otherwise). Regards, Andreas -- SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB 21284 (AG Nürnberg) -- To unsubscribe, e-mail: opensuse-arm+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-arm+owner(a)opensuse.org

4 9

[opensuse-arm] New package: rkdeveloptool
by Andreas Färber 01 May '17

01 May '17

Hello, I have packaged and submitted Rockchip's rkdeveloptool to Factory: https://build.opensuse.org/request/show/492257 In its not-yet-versioned Git state, it already replaces the proprietary upgrade_tool in that it allows to flash, e.g., U-Boot bootloader. Tested on Leap 42.2 with the GeekBox (RK3368). Future improvements shall include installing a udev rule for rockusb devices and fixing the build on excluded platforms (https://github.com/rockchip-linux/rkdeveloptool/issues/6). Regards, Andreas -- SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB 21284 (AG Nürnberg) -- To unsubscribe, e-mail: opensuse-arm+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-arm+owner(a)opensuse.org

1 1