-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
I get these repeated warnings in the log of my home server:
<3.2> 2020-08-01T17:17:14.068115+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.2> 2020-08-01T18:17:14.247482+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data
But the thing is, smartctl can read that disk just fine:
Isengard:~ # smartctl -i /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.12.14-lp151.28.52-default] (SUSE RPM) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: WDC HGST Ultrastar He10 Device Model: WDC WD80EZAZ-11TDBA0 Serial Number: 2TKST2SD LU WWN Device Id: 5 000cca 26af51579 Firmware Version: 83.H0A83 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Aug 1 13:51:20 2020 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
Isengard:~ #
Isengard:~ # smartctl -A /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.12.14-lp151.28.52-default] (SUSE RPM) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0004 128 128 054 Old_age Offline - 116 ...
Isengard:~ # smartctl --test=short /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.12.14-lp151.28.52-default] (SUSE RPM) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Short self-test routine immediately in off-line mode". Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful. Testing has begun. Please wait 2 minutes for test to complete. Test will complete after Sat Aug 1 20:30:49 2020 CEST Use smartctl -X to abort test. Isengard:~ #
Looking at the /var/log/messages file, it gets weirder:
<3.6> 2020-08-01T15:47:03.217524+02:00 Isengard smartd 3543 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], state written to /var/lib/smartmontools/smartd.WDC_WD80EZAZ_11TDBA0-2TKST2SD.ata.state <3.6> 2020-08-01T15:47:04.105688+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], opened <3.6> 2020-08-01T15:47:04.106285+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], WDC WD80EZAZ-11TDBA0, S/N:2TKST2SD, WWN:5-000cca-26af51579, FW:83.H0A83, 8.00 TB <3.6> 2020-08-01T15:47:04.119302+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], found in smartd database: WDC HGST Ultrastar He10 <3.6> 2020-08-01T15:47:04.135383+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], enabled SMART Attribute Autosave. <3.6> 2020-08-01T15:47:04.142911+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], is SMART capable. Adding to "monitor" list. <3.6> 2020-08-01T15:47:04.144358+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], state read from /var/lib/smartmontools/smartd.WDC_WD80EZAZ_11TDBA0-2TKST2SD.ata.state <3.6> 2020-08-01T15:47:04.717689+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], state written to /var/lib/smartmontools/smartd.WDC_WD80EZAZ_11TDBA0-2TKST2SD.ata.state <3.6> 2020-08-01T16:17:12.489203+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-01T16:17:14.439038+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-01T16:17:16.388831+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], Read SMART Self Test Log Failed <3.6> 2020-08-01T16:47:04.708009+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 130 to 132 <3.6> 2020-08-01T17:17:12.118117+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-01T17:17:14.068115+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-01T18:17:12.297698+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-01T18:17:14.247482+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data Isengard:~ #
It did read the temperature change, but it claims the other errors, which are false.
The configuration is:
Isengard:~ # cat /etc/smartd.conf | egrep -v "^[[:space:]]*$|^#" /dev/sda -a -S on -T permissive -s (S/../.././02|L/../../6/03) -m root@telcontar.valinor /dev/disk/by-id/wwn-0x5000c50075a83eaf -d removable -a -o on -S on -s (S/../.././02|L/../../6/03) -m root@telcontar.valinor /dev/disk/by-id/wwn-0x5000c5009399305f -d removable -a -o on -S on -s (S/../.././02|L/../../6/03) -m root@telcontar.valinor /dev/disk/by-id/wwn-0x5000c500c4beb480 -d removable -a -o on -S on -s (S/../.././02|L/../../6/03) -m root@telcontar.valinor /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -d removable -a -S on -s (S/../.././02|L/../../6/03) /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 -d removable -a -S on -s (S/../.././02|L/../../6/03) Isengard:~ #
Ideas?
- -- Cheers
Carlos E. R. (from 15.1 x86_64 at Telcontar)
Hello,
On Sat, 01 Aug 2020, Carlos E. R. wrote:
I get these repeated warnings in the log of my home server:
<3.2> 2020-08-01T17:17:14.068115+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data
[..]
But the thing is, smartctl can read that disk just fine:
[..]
<3.6> 2020-08-01T15:47:04.119302+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], found in smartd database: WDC HGST Ultrastar He10
[..]
<3.6> 2020-08-01T16:17:12.489203+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check
[..]
The configuration is:
Isengard:~ # cat /etc/smartd.conf | egrep -v "^[[:space:]]*$|^#"
[..]
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -d removable -a -S on -s (S/../.././02|L/../../6/03) /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 -d removable -a -S on -s (S/../.././02|L/../../6/03) Isengard:~ #
First, add a newline at the end of the file ;)
Well, SMART-over-USB has quirks. Try '-d sat' in addition to '-d removable'. And BTW: '-S on' should only needed once (if ever). So try this instead of above two:
/dev/[..] -d removable -d sat -a -s (S/../.././02|L/../../6/03)
HTH, -dnh
On 02/08/2020 01.44, David Haller wrote:
Hello,
On Sat, 01 Aug 2020, Carlos E. R. wrote:
I get these repeated warnings in the log of my home server:
<3.2> 2020-08-01T17:17:14.068115+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data
[..]
But the thing is, smartctl can read that disk just fine:
[..]
<3.6> 2020-08-01T15:47:04.119302+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], found in smartd database: WDC HGST Ultrastar He10
[..]
<3.6> 2020-08-01T16:17:12.489203+02:00 Isengard smartd 5945 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check
[..]
The configuration is:
Isengard:~ # cat /etc/smartd.conf | egrep -v "^[[:space:]]*$|^#"
[..]
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -d removable -a -S on -s (S/../.././02|L/../../6/03) /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 -d removable -a -S on -s (S/../.././02|L/../../6/03) Isengard:~ #
First, add a newline at the end of the file ;)
There is one. I usually take care to add one, I was caught by it once or twice ;-)
Well, SMART-over-USB has quirks. Try '-d sat' in addition to '-d removable'. And BTW: '-S on' should only needed once (if ever). So try this instead of above two:
/dev/[..] -d removable -d sat -a -s (S/../.././02|L/../../6/03)
I forgot trying -d sat.
Ok, will see in an hour or two if it works.
With that error, I had to disable the mail on error, because it emailed constantly.
On 02/08/2020 12.34, Carlos E. R. wrote:
On 02/08/2020 01.44, David Haller wrote:
Hello,
On Sat, 01 Aug 2020, Carlos E. R. wrote:
I get these repeated warnings in the log of my home server:
...
Well, SMART-over-USB has quirks. Try '-d sat' in addition to '-d removable'. And BTW: '-S on' should only needed once (if ever). So try this instead of above two:
/dev/[..] -d removable -d sat -a -s (S/../.././02|L/../../6/03)
I forgot trying -d sat.
Ok, will see in an hour or two if it works.
It worked :-)
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
On Sunday, 2020-08-02 at 21:07 +0200, Carlos E. R. wrote:
On 02/08/2020 12.34, Carlos E. R. wrote:
On 02/08/2020 01.44, David Haller wrote:
Hello,
On Sat, 01 Aug 2020, Carlos E. R. wrote:
I get these repeated warnings in the log of my home server:
...
Well, SMART-over-USB has quirks. Try '-d sat' in addition to '-d removable'. And BTW: '-S on' should only needed once (if ever). So try this instead of above two:
/dev/[..] -d removable -d sat -a -s (S/../.././02|L/../../6/03)
I forgot trying -d sat.
Ok, will see in an hour or two if it works.
It worked :-)
Problem is back:
<3.2> 2020-08-07T04:55:34.474986+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.2> 2020-08-07T05:55:34.453302+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.2> 2020-08-07T06:55:34.433409+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.2> 2020-08-07T15:25:34.211163+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data
In detail:
<3.6> 2020-08-06T14:25:24.690040+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], read SMART Attribute Data worked again, warning condition reset after 1 email <3.6> 2020-08-06T14:25:24.690677+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 132 to 130 <3.6> 2020-08-06T14:25:24.700331+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], Read SMART Self-Test Log worked again, warning condition reset after 1 email <3.6> 2020-08-06T14:55:32.262240+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-06T14:55:34.212602+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-06T15:25:25.588123+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], read SMART Attribute Data worked again, warning condition reset after 1 email <3.6> 2020-08-06T16:25:24.915723+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 130 to 132 <3.6> 2020-08-06T16:55:32.520885+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-06T16:55:34.470781+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-06T17:25:24.740938+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], read SMART Attribute Data worked again, warning condition reset after 1 email <3.6> 2020-08-06T17:25:24.742328+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 132 to 130 <3.6> 2020-08-06T17:55:32.350427+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-06T17:55:34.300612+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-06T18:25:24.699400+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], read SMART Attribute Data worked again, warning condition reset after 1 email <3.6> 2020-08-06T18:55:32.330075+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-06T18:55:34.283326+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-06T19:25:25.398939+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], read SMART Attribute Data worked again, warning condition reset after 1 email <3.6> 2020-08-06T20:25:26.791036+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 130 to 132 <3.6> 2020-08-07T00:25:25.152111+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 132 to 130 <3.6> 2020-08-07T00:55:26.847605+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 130 to 132 <3.6> 2020-08-07T01:55:25.166364+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 132 to 130 <3.6> 2020-08-07T02:25:26.903803+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], starting scheduled Short Self-Test. <3.6> 2020-08-07T02:55:25.878498+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], previous self-test completed without error <3.6> 2020-08-07T04:55:32.424237+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-07T04:55:34.474986+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-07T05:25:24.931335+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], read SMART Attribute Data worked again, warning condition reset after 1 email <3.6> 2020-08-07T05:55:32.503160+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-07T05:55:34.453302+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-07T06:25:24.900829+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], read SMART Attribute Data worked again, warning condition reset after 1 email <3.6> 2020-08-07T06:25:24.902800+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 130 to 132 <3.6> 2020-08-07T06:55:32.483636+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-07T06:55:34.433409+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-07T07:25:25.590083+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], read SMART Attribute Data worked again, warning condition reset after 1 email <3.6> 2020-08-07T12:55:26.989310+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 132 to 130 <3.6> 2020-08-07T15:25:32.261050+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-07T15:25:34.211163+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-07T15:55:25.388782+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], read SMART Attribute Data worked again, warning condition reset after 1 email <3.6> 2020-08-07T16:25:25.058723+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 130 to 132 <3.6> 2020-08-07T17:25:25.402340+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 132 to 130 <3.6> 2020-08-07T18:25:26.799720+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 130 to 132 <3.6> 2020-08-08T00:55:26.642655+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 132 to 130
Sometimes it works, sometimes it doesn't, and it sends emails. 18 emails per day
The configuration line is:
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -d removable -d sat -a -s (S/../.././02|L/../../6/03) -m root@telcontar.valinor
Obviously I'm removing the mail part again.
- -- Cheers, Carlos E. R. (from openSUSE 15.1 x86_64 at Telcontar)
Hello,
On Sat, 08 Aug 2020, Carlos E. R. wrote:
It worked :-)
Problem is back:
<3.2> 2020-08-07T04:55:34.474986+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data
[..]
The configuration line is:
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -d removable -d sat -a -s (S/../.././02|L/../../6/03) -m root@telcontar.valinor
Obviously I'm removing the mail part again.
Hm. Try: '-d sat,auto -T permissive' (see 'man 5 smartd.conf')... Otherwise, I'd say that USB-SATA bridge is just b0rked.
HTH, -dnh
On 08/08/2020 07.49, David Haller wrote:
Hello,
On Sat, 08 Aug 2020, Carlos E. R. wrote:
It worked :-)
Problem is back:
<3.2> 2020-08-07T04:55:34.474986+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data
[..]
The configuration line is:
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -d removable -d sat -a -s (S/../.././02|L/../../6/03) -m root@telcontar.valinor
Obviously I'm removing the mail part again.
Hm. Try: '-d sat,auto -T permissive' (see 'man 5 smartd.conf')... Otherwise, I'd say that USB-SATA bridge is just b0rked.
Can't be borked, the disk works fine. I have two units, both do the same thing. Western Digital MyDisk.
After I removed the mail thing yesterday, I got only three warnings.
Now adding your idea, we'll see tomorrow :-)
Huh, no, doesn't like it:
<3.6> 2020-08-08T14:25:00.839082+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0, type changed from 'sat,auto' to 'scsi' <3.6> 2020-08-08T14:25:00.840066+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SCSI], opened <3.6> 2020-08-08T14:25:00.840961+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SCSI], [WD My Book 25EE 4004], lu id: 0x500..., S/N: ..., 8.00 TB <3.6> 2020-08-08T14:25:00.841711+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SCSI], IE (SMART) not enabled, skip device <3.6> 2020-08-08T14:25:00.842439+02:00 Isengard smartd 32172 - - Try 'smartctl -s on /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SCSI]' to turn on SMART features <3.2> 2020-08-08T14:25:00.843166+02:00 Isengard smartd 32172 - - Unable to register SCSI device /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SCSI] at line 129 of file /etc/smartd.conf <3.6> 2020-08-08T14:25:00.844022+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SCSI], not available
It thinks it is SCSI and fails.
I remove the "auto" and it starts.
<3.6> 2020-08-08T14:38:18.444291+02:00 Isengard smartd 32653 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], opened <3.6> 2020-08-08T14:38:18.444948+02:00 Isengard smartd 32653 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], WDC WD 80EZAZ-11TDBA0, S/N:..., WWN:5-000..., FW:83.H0A83, 8.00 TB <3.6> 2020-08-08T14:38:18.457927+02:00 Isengard smartd 32653 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], found in smartd database: WDC HGST Ultrastar He10 <3.6> 2020-08-08T14:38:18.467331+02:00 Isengard smartd 32653 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], is SMART capable. Adding to "monitor" list. <3.6> 2020-08-08T14:38:18.468569+02:00 Isengard smartd 32653 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], state read from /var/lib/smartmontools/smartd.WDC_WD80EZAZ_11TDBA0-2TKST2SD.ata.state
The disk works fine with smartctl, it is smartd which has problems.
Carlos E.R. wrote:
On 08/08/2020 07.49, David Haller wrote:
Hello,
On Sat, 08 Aug 2020, Carlos E. R. wrote:
It worked :-)
Problem is back:
<3.2> 2020-08-07T04:55:34.474986+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data
[..]
The configuration line is:
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -d removable -d sat -a -s (S/../.././02|L/../../6/03) -m root@telcontar.valinor
Obviously I'm removing the mail part again.
Hm. Try: '-d sat,auto -T permissive' (see 'man 5 smartd.conf')... Otherwise, I'd say that USB-SATA bridge is just b0rked.
Can't be borked, the disk works fine.
It _could_ still be broken - using SMART ATA commands is not the same as just doing IO.
Huh, no, doesn't like it:
<3.6> 2020-08-08T14:25:00.839082+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0, type changed from 'sat,auto' to 'scsi'
So your change to sata was ignored, presumably because the USB driver presents the drive as SCSI.
<3.6> 2020-08-08T14:25:00.841711+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SCSI], IE (SMART) not enabled, skip device <3.6> 2020-08-08T14:25:00.842439+02:00 Isengard smartd 32172 - - Try 'smartctl -s on /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SCSI]' to turn on SMART features
Did you try that?
The disk works fine with smartctl, it is smartd which has problems.
I wonder if the issue might be your "-d sat" in the config - seen from the kernel, the disk is not a SATA drive, but a SCSI drive.
On 08/08/2020 15.47, Per Jessen wrote:
Carlos E.R. wrote:
On 08/08/2020 07.49, David Haller wrote:
Hello,
On Sat, 08 Aug 2020, Carlos E. R. wrote:
It worked :-)
Problem is back:
<3.2> 2020-08-07T04:55:34.474986+02:00 Isengard smartd 18959 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data
[..]
The configuration line is:
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -d removable -d sat -a -s (S/../.././02|L/../../6/03) -m root@telcontar.valinor
Obviously I'm removing the mail part again.
Hm. Try: '-d sat,auto -T permissive' (see 'man 5 smartd.conf')... Otherwise, I'd say that USB-SATA bridge is just b0rked.
Can't be borked, the disk works fine.
It _could_ still be broken - using SMART ATA commands is not the same as just doing IO.
I have two units bought on different years, both show the same issue. With smartctl there is no problem, it is with smartd only.
Huh, no, doesn't like it:
<3.6> 2020-08-08T14:25:00.839082+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0, type changed from 'sat,auto' to 'scsi'
So your change to sata was ignored, presumably because the USB driver presents the drive as SCSI.
The reverse.
<3.6> 2020-08-08T14:25:00.841711+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SCSI], IE (SMART) not enabled, skip device <3.6> 2020-08-08T14:25:00.842439+02:00 Isengard smartd 32172 - - Try 'smartctl -s on /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SCSI]' to turn on SMART features
Did you try that?
Yes.
The disk works fine with smartctl, it is smartd which has problems.
I wonder if the issue might be your "-d sat" in the config - seen from the kernel, the disk is not a SATA drive, but a SCSI drive.
I have tried with and without. Same problem.
See, I have connected the second disk this time.
Config:
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -s on -d removable -d sat -T permissive -a -s (S/../.././02|L/../../6/03) /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 -d removable -d sat -a -s (S/../.././02|L/../../6/03)
<3.6> 2020-08-08T20:12:48.752675+02:00 Isengard smartd 32653 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], state written to /var/lib/smartmontools/smartd.WDC_WD80EZAZ_11TDBA0-2TKST2SD.ata.state <3.6> 2020-08-08T20:12:48.917825+02:00 Isengard smartd 9086 - - File /etc/smartd.conf line 129 (drive /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0): warning, character 1 (o) looks odd in extended regular expression on
Line 120 is the first disk above.
<3.6> 2020-08-08T20:12:48.918253+02:00 Isengard smartd 9086 - - File /etc/smartd.conf line 129 (drive /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0): ignoring previous Test Directive -s on <3.6> 2020-08-08T20:12:49.799946+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], opened <3.6> 2020-08-08T20:12:49.800413+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], WDC WD80EZAZ-11TDBA0, S/N:2TKST2SD, WWN:5-000cca-26..., FW:83.H0A83, 8.00 TB <3.6> 2020-08-08T20:12:49.813096+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], found in smartd database: WDC HGST Ultrastar He10 <3.6> 2020-08-08T20:12:49.822400+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], is SMART capable. Adding to "monitor" list. <3.6> 2020-08-08T20:12:49.823702+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], state read from /var/lib/smartmontools/smartd.WDC_WD80EZAZ_11TDBA0-2TKST2SD.ata.state <3.6> 2020-08-08T20:12:49.824274+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], opened <3.6> 2020-08-08T20:12:49.825880+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], WDC WD80EZAZ-11TDBA0, S/N:7HKSUKBJ, WWN:5-000cca-25..., FW:83.H0A83, 8.00 TB <3.6> 2020-08-08T20:12:49.838672+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], found in smartd database: WDC HGST Ultrastar He10 <3.6> 2020-08-08T20:12:49.853064+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], is SMART capable. Adding to "monitor" list. <3.6> 2020-08-08T20:12:49.854560+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], state read from /var/lib/smartmontools/smartd.WDC_WD80EZAZ_11TDBA0-7HKSUKBJ.ata.state <3.6> 2020-08-08T20:12:50.415168+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 141 to 250 <3.6> 2020-08-08T20:12:50.419602+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], state written to /var/lib/smartmontools/smartd.WDC_WD80EZAZ_11TDBA0-2TKST2SD.ata.state <3.6> 2020-08-08T20:12:50.420068+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], state written to /var/lib/smartmontools/smartd.WDC_WD80EZAZ_11TDBA0-7HKSUKBJ.ata.state <3.6> 2020-08-08T20:42:58.521194+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-08T20:43:00.471274+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-08T20:43:02.420908+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], Read SMART Self Test Log Failed <3.6> 2020-08-08T20:43:11.536628+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-08T20:43:13.486658+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-08T20:43:15.436411+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], Read SMART Self Test Log Failed <3.6> 2020-08-08T20:43:17.386206+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], Read Summary SMART Error Log failed <3.6> 2020-08-08T20:43:17.386830+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], old test of type L not run at Sat Jul 4 03:00:00 2020 CEST, starting now. <3.2> 2020-08-08T20:43:19.336063+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], not capable of Offline or Self-Testing. <3.6> 2020-08-08T21:12:51.964169+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 250 to 162 <3.6> 2020-08-08T21:42:58.551103+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-08T21:43:00.500978+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-08T21:43:10.933802+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-08T21:43:12.883854+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-08T21:43:14.833631+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], Read SMART Self Test Log Failed <3.6> 2020-08-08T21:43:16.784271+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], Read Summary SMART Error Log failed <3.6> 2020-08-08T22:12:52.396979+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], SMART Prefailure Attribute: 3 Spin_Up_Time changed from 253 to 251 <3.6> 2020-08-08T22:12:52.397599+02:00 Isengard smartd 9086 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 162 to 154
It says it is not self check capable, this is not true, they are both perfectly capable with default settings:
Isengard:~ # smartctl --test=short /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.12.14-lp151.28.52-default] (SUSE RPM) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Short self-test routine immediately in off-line mode". Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful. Testing has begun. Please wait 2 minutes for test to complete. Test will complete after Sat Aug 8 22:48:48 2020 CEST Use smartctl -X to abort test. Isengard:~ # smartctl --test=short /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.12.14-lp151.28.52-default] (SUSE RPM) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Short self-test routine immediately in off-line mode". Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful. Testing has begun. Please wait 2 minutes for test to complete. Test will complete after Sat Aug 8 22:48:55 2020 CEST Use smartctl -X to abort test. Isengard:~ #
And the logs can be read just fine:
Isengard:~ # smartctl --log=selftest /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.12.14-lp151.28.52-default] (SUSE RPM) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION === SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 10205 - # 2 Extended offline Aborted by host 90% 10186 - # 3 Short offline Completed without error 00% 10184 - # 4 Short offline Completed without error 00% 10160 - # 5 Short offline Completed without error 00% 10136 - # 6 Short offline Completed without error 00% 10112 - # 7 Short offline Completed without error 00% 10088 - # 8 Short offline Completed without error 00% 10064 - # 9 Short offline Completed without error 00% 10040 - #10 Short offline Completed without error 00% 10034 - #11 Extended offline Aborted by host 80% 10019 - #12 Short offline Completed without error 00% 10016 - #13 Short offline Completed without error 00% 9992 - #14 Short offline Completed without error 00% 9968 - #15 Short offline Completed without error 00% 9944 - #16 Short offline Completed without error 00% 9920 - #17 Short offline Completed without error 00% 9896 - #18 Short offline Completed without error 00% 9872 - #19 Extended offline Aborted by host 90% 9850 - #20 Short offline Completed without error 00% 9848 - #21 Short offline Completed without error 00% 9824 -
Isengard:~ # smartctl --log=selftest /dev/disk/by-id/usb-WD_My_Book_25EE_3 usb-WD_My_Book_25EE_32544B5354325344-0:0 usb-WD_My_Book_25EE_37484B53554B424A-0:0 usb-WD_My_Book_25EE_32544B5354325344-0:0-part1 usb-WD_My_Book_25EE_37484B53554B424A-0:0-part1 Isengard:~ # smartctl --log=selftest /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.12.14-lp151.28.52-default] (SUSE RPM) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION === SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5207 - # 2 Short offline Completed without error 00% 5184 - # 3 Short offline Completed without error 00% 5160 - # 4 Short offline Completed without error 00% 5136 - # 5 Short offline Completed without error 00% 5113 - # 6 Short offline Completed without error 00% 5089 - # 7 Short offline Completed without error 00% 5065 - # 8 Short offline Completed without error 00% 5017 - # 9 Short offline Completed without error 00% 4993 - #10 Short offline Completed without error 00% 4969 - #11 Short offline Completed without error 00% 4945 - #12 Short offline Completed without error 00% 4921 - #13 Short offline Completed without error 00% 4897 - #14 Short offline Completed without error 00% 4849 - #15 Short offline Completed without error 00% 4801 - #16 Short offline Completed without error 00% 4777 - #17 Short offline Completed without error 00% 4729 - #18 Short offline Completed without error 00% 4681 - #19 Short offline Completed without error 00% 4658 - #20 Short offline Completed without error 00% 4634 - #21 Short offline Completed without error 00% 4586 -
Isengard:~ #
Isengard:~ # smartctl --scan-open /dev/sda -d sat # /dev/sda [SAT], ATA device /dev/sdb -d sat # /dev/sdb [SAT], ATA device /dev/sdc -d sat # /dev/sdc [SAT], ATA device /dev/sdd -d sat # /dev/sdd [SAT], ATA device /dev/sde -d sat # /dev/sde [SAT], ATA device /dev/sdf -d sat # /dev/sdf [SAT], ATA device Isengard:~ #
It is some problem with smartd, and I had it for years. Since I bought some disks it doesn't like. Then, one year the software gets an update and one disk that failed then works. It is a software problem in the daemon.
I'm testing now:
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -s on -d removable -d sat,12 -T permissive -a -s (S/../.././02|L/../../6/03)
/dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 -d removable -d sat,16 -T permissive -T permissive -T permissive -T permissive -a -s (S/../.././02|L/../../6/03)
I tried "verypermissive", which is listed in the man page, but it complains:
Aug 08 23:06:12 Isengard smartd[13611]: File /etc/smartd.conf line 137 (drive /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0): Invalid argument to -T Directive: verypermissive
On 08/08/2020 23.10, Carlos E. R. wrote:
On 08/08/2020 15.47, Per Jessen wrote:
Carlos E.R. wrote:
On 08/08/2020 07.49, David Haller wrote:
...
It is some problem with smartd, and I had it for years. Since I bought some disks it doesn't like. Then, one year the software gets an update and one disk that failed then works. It is a software problem in the daemon.
I'm testing now:
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -s on -d removable -d sat,12 -T permissive -a -s (S/../.././02|L/../../6/03)
/dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 -d removable -d sat,16 -T permissive -T permissive -T permissive -T permissive -a -s (S/../.././02|L/../../6/03)
I tried "verypermissive", which is listed in the man page, but it complains:
Aug 08 23:06:12 Isengard smartd[13611]: File /etc/smartd.conf line 137 (drive /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0): Invalid argument to -T Directive: verypermissive
/dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 -s on -d removable -d sat,12 -T permissive -a -s (S/../.././02|L/../../6/03) /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 -d removable -d sat,16 -T permissive -T permissive -T permissive -T permissive -a -s (S/../.././02|L/
grep My_Book /var/log/messages | less
<3.6> 2020-08-08T23:08:24.362845+02:00 Isengard smartd 13663 - - File /etc/smartd.conf line 129 (drive /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0): warning, character 1 (o) looks odd in extended regular expression on <3.6> 2020-08-08T23:08:24.363748+02:00 Isengard smartd 13663 - - File /etc/smartd.conf line 129 (drive /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0): ignoring previous Test Directive -s on <3.6> 2020-08-08T23:08:25.261652+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], opened <3.6> 2020-08-08T23:08:25.262178+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], WDC WD80EZAZ-11TDBA0, S/N:2TKST2SD, WWN:5-..., FW:83.H0A83, 8.00 TB <3.6> 2020-08-08T23:08:25.274823+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], found in smartd database: WDC HGST Ultrastar He10 <3.6> 2020-08-08T23:08:25.300774+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], is SMART capable. Adding to "monitor" list. <3.6> 2020-08-08T23:08:25.302176+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], state read from /var/lib/smartmontools/smartd.WDC_WD80EZAZ....ata.state <3.6> 2020-08-08T23:08:25.303004+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], opened <3.6> 2020-08-08T23:08:25.303840+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], WDC WD80EZAZ-11TDBA0, S/N:7HKSUKBJ, WWN:5-..., FW:83.H0A83, 8.00 TB <3.6> 2020-08-08T23:08:25.316372+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], found in smartd database: WDC HGST Ultrastar He10 <3.6> 2020-08-08T23:08:25.336885+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], is SMART capable. Adding to "monitor" list. <3.6> 2020-08-08T23:08:25.338318+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], state read from /var/lib/smartmontools/smartd.WDC_WD8...BJ.ata.state <3.6> 2020-08-08T23:08:25.960333+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], state written to /var/lib/smartmontools/smartd.WDC_WD...SD.ata.state <3.6> 2020-08-08T23:08:25.961091+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], state written to /var/lib/smartmontools/smartd.WDC_WD8...BJ.ata.state <3.6> 2020-08-08T23:38:33.780662+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-08T23:38:35.730568+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-08T23:38:37.680316+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], Read SMART Self Test Log Failed <3.6> 2020-08-08T23:38:46.498530+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], not capable of SMART self-check <3.2> 2020-08-08T23:38:48.448248+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], failed to read SMART Attribute Data <3.6> 2020-08-08T23:38:50.398066+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], Read SMART Self Test Log Failed <3.6> 2020-08-08T23:38:52.347999+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], Read Summary SMART Error Log failed <3.6> 2020-08-09T00:08:25.991349+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 132 to 130 <3.6> 2020-08-09T00:08:26.952448+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_37484B53554B424A-0:0 [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 144 to 151 <3.6> 2020-08-09T00:38:33.558901+02:00 Isengard smartd 13663 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0 [SAT], not capable of SMART self-check
As you can see, both disks fail. They can't be both "borked". Then sometimes it logs temperature change. The problem is smartd itself. smartctl copes fine.
Carlos E. R. wrote:
With smartctl there is no problem, it is with smartd only.
So presumably a config issue.
Huh, no, doesn't like it:
<3.6> 2020-08-08T14:25:00.839082+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0, type changed from 'sat,auto' to 'scsi'
So your change to sata was ignored, presumably because the USB driver presents the drive as SCSI.
The reverse.
The way I read the above "type changed from 'sat,auto' to 'scsi'" is that the type was changed from 'sat,auto' to 'scsi' ?
The disk works fine with smartctl, it is smartd which has problems.
I wonder if the issue might be your "-d sat" in the config - seen from the kernel, the disk is not a SATA drive, but a SCSI drive.
I have tried with and without. Same problem.
Hmm. Maybe its a problem to bring up on the smartmontools list?
On 09/08/2020 18.44, Per Jessen wrote:
Carlos E. R. wrote:
With smartctl there is no problem, it is with smartd only.
So presumably a config issue.
Maybe, but what? That's what I hoped, but I'm out of ideas.
Huh, no, doesn't like it:
<3.6> 2020-08-08T14:25:00.839082+02:00 Isengard smartd 32172 - - Device: /dev/disk/by-id/usb-WD_My_Book_25EE_32544B5354325344-0:0, type changed from 'sat,auto' to 'scsi'
So your change to sata was ignored, presumably because the USB driver presents the drive as SCSI.
The reverse.
The way I read the above "type changed from 'sat,auto' to 'scsi'" is that the type was changed from 'sat,auto' to 'scsi' ?
I did not change to sata, I changed to "sata, auto". It should have kept the sata part, not tried scssi, IMHO.
The disk works fine with smartctl, it is smartd which has problems.
I wonder if the issue might be your "-d sat" in the config - seen from the kernel, the disk is not a SATA drive, but a SCSI drive.
I have tried with and without. Same problem.
Hmm. Maybe its a problem to bring up on the smartmontools list?
I tried, years ago. Dead silence.
-
Carlos E. R. -
Carlos E.R. -
David Haller -
Per Jessen