Moin, ich habe hier ein 8.0 mit - einem Tekram DC390/AM53C974 - einem Plextor PX-32TS SCSI-CD-ROM - einem NEC ND-3520A DVD-RW (hdc) - einem NEC DV-5800B DVD-ROM (hdd) Das Plextor hängt am Tekram, der Brenner wird über ide-scsi eingebunden, das DVD-ROM hängt an hdd (und läuft über ide). Allerdings wird das Plextor als /dev/sr0 eingebunden, und nicht als /dev/scd0. Das würde mich nicht weiter stören, aber beim Audio-Grabben war es schnarchlangsam (ca. 0,1x). Ich habe mal die dmesg angehängt. Im /etc/modules.conf findet sich zu scsi nur --------------------- alias scsi_hostadapter off # ide-scsi #pre-install sg modprobe ide-scsi # load ide-scsi before sg #pre-install sr_mod modprobe ide-scsi # load ide-scsi before sr_mod #pre-install ide-scsi modprobe ide-cd # load ide-cd before ide-scsi --------------------- /etc/sysconfig/kernel: --------------------- INITRD_MODULES="tmscsim reiserfs ide-scsi" --------------------- Und im lilo.conf wird ide-scsi für hdc geladen: --------------------- append = "hdc=ide-scsi" --------------------- Was muß ich ändern, damit das Plextor an /dev/scd0 landet (und bringt das was beim Audio-Grabben)? Danke im Voraus Martin PS: dmesg: --------------------- Linux version 2.4.18-4GB (root@Pentium.suse.de) (gcc version 2.95.3 20010315 (SuSE)) #1 Wed Mar 27 13:57:05 UTC 2002 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) Scanning bios EBDA for MXT signature On node 0 totalpages: 131056 zone(0): 4096 pages. zone(1): 126960 pages. zone(2): 0 pages. Building zonelist for node : 0 Kernel command line: auto BOOT_IMAGE=linux ro root=307 hdc=ide-scsi ide_setup: hdc=ide-scsi Initializing CPU#0 Detected 1400.055 MHz processor. Console: colour dummy device 80x25 Calibrating delay loop... 2791.83 BogoMIPS Memory: 512732k/524224k available (1389k kernel code, 11104k reserved, 406k data, 120k init, 0k highmem) Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) CPU: Before vendor init, caps: 0383f9ff c1c3f9ff 00000000, vendor = 2 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After vendor init, caps: 0383f9ff c1c3f9ff 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0383f9ff c1c3f9ff 00000000 00000000 CPU: Common caps: 0383f9ff c1c3f9ff 00000000 00000000 CPU: AMD Athlon(tm) XP 1600+ stepping 02 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel PCI: PCI BIOS revision 2.10 entry at 0xfb240, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Using IRQ router default [1106/3099] at 00:00.0 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16) mxt_scan_bios: enter Starting kswapd kinoded started VFS: Diskquotas version dquot_6.5.0 initialized ACPI: APM is already active, exiting vesafb: framebuffer at 0xd8000000, mapped to 0xe080d000, size 65536k vesafb: mode is 800x600x16, linelength=1600, pages=67 vesafb: protected mode interface info at c000:5438 vesafb: scrolling: redraw vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0 Looking for splash picture.... found (800x600, 30406 bytes). Console: switching to colour frame buffer device 82x26 fb0: VESA VGA frame buffer device pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI SERIAL_ACPI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10e block: 128 slots per queue, batch=32 RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 89 PCI: No IRQ known for interrupt pin A of device 00:11.1. Please try using pci=biosirq. VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci00:11.1 ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA hda: ST340016A, ATA DISK drive hdb: SAMSUNG SP1614N, ATA DISK drive hdc: _NEC DVD_RW ND-3520A, ATAPI CD/DVD-ROM drive hdd: _NEC DV-5800B, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 blk: queue c031ece4, I/O limit 4095Mb (mask 0xffffffff) hda: safely enabled flush hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(100) blk: queue c031ee34, I/O limit 4095Mb (mask 0xffffffff) hdb: safely enabled flush hdb: 312581808 sectors (160042 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100) hdd: no flushcache support hdd: ATAPI 48X DVD-ROM drive, 512kB Cache Uniform CD-ROM driver Revision: 3.12 ide-floppy driver 0.99 Partition check: hda: hda1 hda2 < hda5 hda6 hda7 > hdb: hdb1 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 16 devices) Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994 Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak. ide-floppy driver 0.99 SCSI subsystem driver Revision: 1.00 request_module[scsi_hostadapter]: Root fs not mounted request_module[scsi_hostadapter]: Root fs not mounted md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 32768) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Uncompressing.............done. Freeing initrd memory: 593k freed VFS: Mounted root (ext2 filesystem). DC390: 1 adapters found scsi0 : Tekram DC390/AM53C974 V2.0f 2000-12-20 Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02 Type: CD-ROM ANSI SCSI revision: 02 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0 DC390: Target 6: Sync transfer 10.0 MHz, Offset 15 sr0: scsi-1 drive hdc: no flushcache support scsi1 : SCSI host adapter emulation for IDE ATAPI devices Vendor: _NEC Model: DVD_RW ND-3520A Rev: 1.04 Type: CD-ROM ANSI SCSI revision: 02 Attached scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0 sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray reiserfs: checking transaction log (device 03:07) ... Using r5 hash to sort names ReiserFS version 3.6.25 VFS: Mounted root (reiserfs filesystem) readonly. change_root: old root has d_count=2 Trying to unmount old root ... okay Freeing unused kernel memory: 120k freed LVM version 1.0.3(19/02/2002) module loaded Adding Swap: 1052216k swap-space (priority 42) NTFS driver v1.1.22 [Flags: R/O MODULE] reiserfs: checking transaction log (device 03:41) ... Using r5 hash to sort names ReiserFS version 3.6.25 usb.c: registered new driver usbdevfs usb.c: registered new driver hub PCI: Setting latency timer of device 00:11.5 to 64 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 00:0c.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xd400. Vers LK1.1.16 usb-uhci.c: $Revision: 1.275 $ time 14:22:01 Mar 27 2002 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: USB UHCI at I/O 0xdc00, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,1) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Installing knfsd (copyright (C) 1996 okir@monad.swb.de). IPv6 v0.8 for NET4.0 IPv6 over IPv4 tunneling driver eth0: no IPv6 routers present --------------------- -- Martin Schröder, ms@artcom-gmbh.de ArtCom GmbH, Lise-Meitner-Str 5, 28359 Bremen, Germany Voice +49 421 20419-44 / Fax +49 421 20419-10 http://www.artcom-gmbh.de