smartctl 5.39 2008-05-08 21:56 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-8 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST31000340NS Serial Number: 9QJ2Y99D Firmware Version: SN05 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Tue Oct 4 13:55:39 2011 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 634) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 238) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 082 058 044 Pre-fail Always - 186936673 3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 134 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1 7 Seek_Error_Rate 0x000f 082 060 030 Pre-fail Always - 13375432073 9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 20394 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 037 020 Old_age Always - 134 184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 122 188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 097 097 000 Old_age Always - 3 190 Airflow_Temperature_Cel 0x0022 068 057 045 Old_age Always - 32 (Lifetime Min/Max 28/32) 194 Temperature_Celsius 0x0022 032 043 000 Old_age Always - 32 (0 13 0 0) 195 Hardware_ECC_Recovered 0x001a 037 021 000 Old_age Always - 186936673 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 122 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 122 occurred at disk power-on lifetime: 20335 hours (847 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 2d+18:05:48.771 READ DMA EXT 27 00 00 00 00 00 e0 00 2d+18:05:48.769 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 2d+18:05:48.747 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 2d+18:05:48.734 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 2d+18:05:48.689 READ NATIVE MAX ADDRESS EXT Error 121 occurred at disk power-on lifetime: 20335 hours (847 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 2d+18:05:45.671 READ DMA EXT 27 00 00 00 00 00 e0 00 2d+18:05:45.669 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 2d+18:05:45.653 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 2d+18:05:45.639 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 2d+18:05:45.589 READ NATIVE MAX ADDRESS EXT Error 120 occurred at disk power-on lifetime: 20335 hours (847 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 2d+18:05:42.559 READ DMA EXT 27 00 00 00 00 00 e0 00 2d+18:05:42.557 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 2d+18:05:42.534 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 2d+18:05:42.521 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 2d+18:05:42.477 READ NATIVE MAX ADDRESS EXT Error 119 occurred at disk power-on lifetime: 20335 hours (847 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 2d+18:05:39.459 READ DMA EXT 27 00 00 00 00 00 e0 00 2d+18:05:39.457 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 2d+18:05:39.435 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 2d+18:05:39.422 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 2d+18:05:39.377 READ NATIVE MAX ADDRESS EXT Error 118 occurred at disk power-on lifetime: 20335 hours (847 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 2d+18:05:36.387 READ DMA EXT 27 00 00 00 00 00 e0 00 2d+18:05:36.385 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 2d+18:05:36.364 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 2d+18:05:36.290 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 2d+18:05:36.273 READ NATIVE MAX ADDRESS EXT SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.