Your experience sounds a lot like what I have gone through recently. I bought a new computer (this tale has been on this list), installed Leap 15.3 (not Tumbleweed) booted it up, and it worked...for a few minutes, between 5 and 15...and then screen went black and the power supply, and case fans started spinning at 100%--totally hung, only way out was pulling the power cord. Nothing I tried could resolve the issue....I thought it was a driver issue with the nvidia graphics card, but that lead nowhere. So, I bought a 3-year old used computer (happily I can disable the UEFI stuff on this one...UEFI can not be disabled on the new one.), installed 15.3 and it is stable and happy. I would love to get the new computer working with Leap, so if you resolve your problem, please share your solution. It may help, or (of course) it may not.
lm-sensors and the setup including the new directory is installed and working.
I had to reinstall my TW, before all worked error free.
But now, no plasmoid seems to "see" the sensors. When I however go to CLI and
do as normal user:
entropy@silversurfer:~> sensors
fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 60.33 W (crit = 95.06 W)
amdgpu-pci-0300
Adapter: PCI adapter
vddgfx: 6.00 mV
fan1: 2300 RPM (min = 0 RPM, max = 5400 RPM)
edge: +59.0°C (crit = +110.0°C, hyst = -273.1°C)
(emerg = +115.0°C)
junction: +60.0°C (crit = +105.0°C, hyst = -273.1°C)
(emerg = +110.0°C)
mem: +0.0°C (crit = +105.0°C, hyst = -273.1°C)
(emerg = +110.0°C)
slowPPT: 14.00 W (cap = 105.00 W)
it8728-isa-0228
Adapter: ISA adapter
in0: 1.20 V (min = +0.00 V, max = +3.06 V)
in1: 1.49 V (min = +0.00 V, max = +3.06 V)
in2: 2.02 V (min = +0.00 V, max = +3.06 V)
in3: 1.97 V (min = +0.00 V, max = +3.06 V)
in4: 1.96 V (min = +0.00 V, max = +3.06 V)
in5: 660.00 mV (min = +0.00 V, max = +3.06 V)
in6: 2.22 V (min = +0.00 V, max = +3.06 V)
3VSB: 3.29 V (min = +0.00 V, max = +6.12 V)
Vbat: 3.14 V
fan1: 992 RPM (min = 10 RPM)
fan2: 1057 RPM (min = 0 RPM)
fan3: 0 RPM (min = 0 RPM)
fan4: 0 RPM (min = 0 RPM)
fan5: 0 RPM (min = 0 RPM)
temp1: +48.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
temp2: +50.0°C (low = +127.0°C, high = +127.0°C) sensor = thermal
diode
temp3: +27.0°C (low = +0.0°C, high = +90.0°C) sensor = Intel PECI
intrusion0: ALARM
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +27.4°C (high = +70.0°C)
(crit = +80.0°C, hyst = +77.0°C)
Three fans as expected (cpu and 2 PWR system ones)
All sensors are there, but none is seen. Could this be a permissions issue?
Any hint why the plasmoids do not have access to the existing values of lm-
sensors?
I have also reinstalled all sensor related plasmoid from the web again, but
nothing, included reboot.
Thankful for some clue about this.
Again: ANY sensor is seen of the above in plasma.