Hi Dennis,

�

as I wrote:

�

the correct adaptions of SANE to the HP Scanjet 5300c have been made.

�

Here are my systems messages:

�:~ # scanimage -L

device `avision:libusb:002:013' is a Hewlett-Packard ScanJet 5300C flatbed scanner

:~ #

and

�:~ # zypper se -si sane hplip

Loading repository data...

Reading installed packages...

---+--------------------------+---------+--------------------+--------+--------------------------------

i+ | hplip | package | 3.19.12-lp152.1.1 | x86_64 | Haupt-Repository

i | hplip-hpijs | package | 3.19.12-lp152.1.1 | x86_64 | Haupt-Repository

i | hplip-sane | package | 3.19.12-lp152.1.1 | x86_64 | Haupt-Repository

i | libKF5Sane5 | package | 20.04.2-lp152.1.1 | x86_64 | Haupt-Repository

i | sane-backends | package | 1.0.31-lp152.7.3.1 | x86_64 | Hauptaktualisierungs-Repository

i | sane-backends-32bit | package | 1.0.31-lp152.7.3.1 | x86_64 | Hauptaktualisierungs-Repository

i | sane-backends-autoconfig | package | 1.0.31-lp152.7.3.1 | x86_64 | Hauptaktualisierungs-Repository

i+ | xsane | package | 0.999-lp152.3.8 | x86_64 | Haupt-Repository

:~ #

�

Remark:

I have an y-axis scaling problem as further mentioned...

�

The problem occurs with simple-scan and XSane Scanner Tools.

The thing I don't understand is why it has worked in openSUSE Leap 15.1 and why not now?

The core problem could be related to the different packages used by 15.1 compared to 15.2.

�

xsane-0.999-lp151.2.3.x86_64.rpm

hplip-3.18.6-lp151.1.1.x86_64.rpm

hplip-hpijs-3.18.6-lp151.1.1.x86_64.rpm

hplip-sane-3.18.6-lp151.1.1.x86_64.rpm

�

xsane-0.999-lp152.3.8.x86_64.rpm

hplip-3.19.12-lp152.1.1.x86_64.rpm

hplip-hpijs-3.19.12-lp152.1.1.x86_64.rpm

hplip-sane-3.19.12-lp152.1.1.x86_64.rpm

�

Any ideas?

�

--------------------------------------------------------

Am Freitag, 4. Dezember 2020, 19:51:30 CET schrieb DennisG:

On 12/4/20 12:15 PM, michael.kasimir@ wrote:

�

If you did not already, you should try to install the scanner with

YaST/Scanner.� It will install the HP driver avision.� The driver info

indicates that it supports up to 2400 dpi, but also cautions that some

firmware revisions have x-axis scaling problems when using >1200 dpi.

�

Both simple-scan and skanlite use the xsane backend which is probably

where the problem is.� The HP driver adds on to xsane.� I am using

another HP scanner with its HP provided driver and it scans perfectly.

�

_______________________________________________

openSUSE Support mailing list -- support@lists.opensuse.org

To unsubscribe, email support-leave@lists.opensuse.org

List Netiquette: https://en.opensuse.org/openSUSE:Mailing_list_netiquette

List Archives:

https://lists.opensuse.org/archives/list/support@lists.opensuse.org

kate

�