On Fri, 6 Feb 2009 22:53:34 +0100 Carlos Lorenzo Matés wrote:

Hi Vladimir.

El Viernes, 6 de Febrero de 2009, Vladimir Botka escribió:

...

On Fri, 6 Feb 2009 07:38:03 +0100

Carlos Lorenzo Matés wrote:

...

Hi to All.

I had setup my Bluetooth Headsets (Neovoice) using the howto found in the opensuse.org wiki

I'm using opensuse 11.1 (up to date)

The headsets are paired and working.

...

...

I can talk and hear myself in the headset, so seems to work fine.

But I'm unable to use with applications like Teamspeak because they expect a device like /dev/dsp or similar.

thank you for the feedback. Unfortunately the microphone is not supported yet. If you put profile "auto" into the .asoundrc you get

As of the PulseAudio (PA). The 0.9.12 version does not provide you with microphone support either, even if you succeed to set it up. The PA receives/sends the sound via module-alsa-source/module-alsa-sink from/to alsa again. wait for the PA 0.9.13. There will be PA native bluetooth support.

[1] http://en.opensuse.org/BT_headphones#Notes.

yes, I used this url to setup my headsets, but later i modified to try to get the pacl commands to work.

I also tried installing pulseaudio 0.9.14 from the gnome factory repos, but not to avail

Do you know if it will be possible to make any kind of link from a /dev/ entry to the btheadset to make the headset visible to any application?

Thanks

You can install pulseaudio 0.9.14 from the GNOME:Factory repository [1]. First download the file GNOME:Factory.repo from [1] and then as a root add the repo "$ zypper ar GNOME:Factory.repo" . You should be able to install the 0.9.14 then. If you have any kind of problem, tell me. I would like to help you. I am going to install and test this version too. No link helps to make the bluetooth (BT) headset visible to application. The BT sound devices do not create /dev/ entries on their own. At present the BT sound devices in openSUSE communicate with ALSA soundsystem only. Thus you can use BT headset with applications which support the output configuration to specific alsa device (specified in ~/.asoundrc) [2]. If your application does not allow this kind of configuration you can also try to set the default alsa device to your BT headset too. This will help of course only if this application sends the output to alsa. [1] http://download.opensuse.org/repositories/GNOME:/Factory/openSUSE_11.1/ [2] http://wiki.bluez.org/wiki/HOWTO/AudioDevices#SupportedPlayers Ciao, -- -vlado Vladimir Botka -- To unsubscribe, e-mail: opensuse-multimedia+unsubscribe@opensuse.org For additional commands, e-mail: opensuse-multimedia+help@opensuse.org

On Wed, 11 Feb 2009 19:08:59 +0100 Carlos Lorenzo Matés wrote:

could you explain how to make the bt headsets the default alsa input and output?

I have tried with this

in .asoundrc pcm.!default { type pulse } ctl.!default { type pulse }

pcm.!default { type bluetooth device "00:0E:16:02:22:4D" profile auto } about the ctl I am not sure.

then launch the application with aoss

ie:

aoss ./Teamspeak

the application accepts devices like

oss: /dev/dsp

If this works you can also try: "alsa: device=btheadset", but again I am not sure. This question would be best answered from the aoss mailling-list. "How to set specific alsa device as an aoss output ?"

i set this /dev/dsp0

but the /dev/dsp0 get not redirected to the btheadsets.

the application gives no error and display my device as active, but i hear any sound

is the

pcm.dsp0 { type plug slave.pcm "btheadset" }

right?

This construct looks OK to me regarding the documentation in http://alsa.opensrc.org/.asoundrc, but again this settings would be best consulted in the alsa mailing-list.

as a side note, the pactl load-module module-alsa-source device=btheadset still breaks pulseaudio

I try to get bluetooth/pulseaudio working too. Ciao, -- -vlado Vladimir Botka -- To unsubscribe, e-mail: opensuse-multimedia+unsubscribe@opensuse.org For additional commands, e-mail: opensuse-multimedia+help@opensuse.org