Hatte eine
Installation von Hylafax mit Sedlbauer Fax+ PCI unter SuSE 7.0, die tadellos
lief.
Jetzt hab ich
auf SuSE 8.1 umgestellt (Neuinstallation). Alle anderen Serverdienste habe ich
auf Anhieb wieder zum Laufen bekommen (inklusive vbox) und auch das Senden von
Faxen mit Hylafax geht, nur beim Empfang bricht das Teil immer an der selben
Stelle ab.
Auf der Seite von Sedlbauer gibts zwar einen Kernelpatch, der
ist aber fuer Kernel 2.4.18 (SuSE 8.0) und ich weiss auch nicht, ob das was
bringt. Ich hatte eigentlich gehofft, der neue Kernel waere entsprechend
verbessert.
Hier ist mal ein typisches Logfile aufgelistet (hab nur meine
Nummer geixt):
Dec 26 17:55:34.86: [ 4956]: SESSION BEGIN 00000018
xxx
Dec 26 17:55:34.86: [ 4956]: HylaFAX (tm) Version 4.1.3
Dec 26
17:55:34.86: [ 4956]: MODEM set XON/XOFF/FLUSH: input ignored, output
disabled
Dec 26 17:55:34.86: [ 4956]: <-- [4:ATA\r]
Dec 26 17:55:40.07:
[ 4956]: --> [7:CONNECT]
Dec 26 17:55:40.07: [ 4956]: ANSWER: FAX
CONNECTION DEVICE '/dev/ttyI0'
Dec 26 17:55:40.07: [ 4956]: MODEM input
buffering enabled
Dec 26 17:55:40.07: [ 4956]: RECV FAX: begin
Dec 26
17:55:40.07: [ 4956]: RECV FAX: CDPN=20
Dec 26 17:55:40.07: [ 4956]: MODEM
input buffering disabled
Dec 26 17:55:40.07: [ 4956]: <-- data [23]
Dec
26 17:55:40.07: [ 4956]: <-- data [2]
Dec 26 17:55:40.09: [ 4956]: -->
[7:CONNECT]
Dec 26 17:55:40.09: [ 4956]: <-- data [10]
Dec 26
17:55:40.09: [ 4956]: <-- data [2]
Dec 26 17:55:41.21: [ 4956]: -->
[2:OK]
Dec 26 17:55:41.21: [ 4956]: <-- [9:AT+FRH=3D3\r]
Dec 26
17:55:41.55: [ 4956]: --> [7:CONNECT]
Dec 26 17:55:43.04: [ 4956]: -->
[2:OK]
Dec 26 17:55:43.04: [ 4956]: REMOTE TSI "6913305099931"
Dec 26
17:55:43.04: [ 4956]: <-- [9:AT+FRH=3D3\r]
Dec 26 17:55:43.05: [ 4956]:
--> [7:CONNECT]
Dec 26 17:55:43.29: [ 4956]: --> [2:OK]
Dec 26
17:55:43.29: [ 4956]: REMOTE wants 14400 bit/s
Dec 26 17:55:43.29: [ 4956]:
REMOTE wants page width 1728 pixels in 215 mm
Dec 26 17:55:43.29: [ 4956]:
REMOTE wants A4 page length (297 mm)
Dec 26 17:55:43.29: [ 4956]: REMOTE
wants 7.7 line/mm
Dec 26 17:55:43.29: [ 4956]: REMOTE wants 2-D MR
Dec 26
17:55:43.29: [ 4956]: RECV training at v.17 14400 bit/s
Dec 26 17:55:43.29: [
4956]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
Dec 26
17:55:43.29: [ 4956]: <-- [11:AT+FRM=3D145\r]
Dec 26 17:55:45.04: [ 4956]:
--> [7:CONNECT]
Dec 26 17:55:46.66: [ 4956]: MODEM set XON/XOFF/DRAIN:
input ignored, output disabled
Dec 26 17:55:46.66: [ 4956]: RECV: TCF 2913
bytes, 6% non-zero, 2699 zero-run
Dec 26 17:55:46.66: [ 4956]: --> [10:NO
CARRIER]
Dec 26 17:55:46.66: [ 4956]: DELAY 75 ms
Dec 26 17:55:46.74: [
4956]: TRAINING succeeded
Dec 26 17:55:46.74: [ 4956]: <--
[9:AT+FTH=3D3\r]
Dec 26 17:55:48.37: [ 4956]: --> [7:CONNECT]
Dec 26
17:55:48.37: [ 4956]: <-- data [3]
Dec 26 17:55:48.37: [ 4956]: <--
data [2]
Dec 26 17:55:48.63: [ 4956]: --> [2:OK]
Dec 26 17:55:48.63: [
4956]: MODEM input buffering enabled
Dec 26 17:55:48.63: [ 4956]: MODEM set
XON/XOFF/FLUSH: input ignored, output generated
Dec 26 17:55:48.63: [ 4956]:
<-- [11:AT+FRM=3D146\r]
Dec 26 17:55:49.29: [ 4956]: -->
[7:CONNECT]
Dec 26 17:55:49.29: [ 4956]: RECV: begin page
Dec 26
17:56:00.79: [ 4956]: RECV: 2300 total lines, 0 bad lines, 0 consecutive bad
lines
Dec 26 17:56:00.79: [ 4956]: RECV: end page
Dec 26 17:56:00.79: [
4956]: --> [10:NO CARRIER]
Dec 26 17:56:00.79: [ 4956]: MODEM set
XON/XOFF/DRAIN: input ignored, output disabled
Dec 26 17:56:00.79: [ 4956]:
MODEM input buffering disabled
Dec 26 17:56:00.79: [ 4956]: <--
[9:AT+FRH=3D3\r]
Dec 26 17:56:00.95: [ 4956]: --> [7:CONNECT]
Dec 26
17:56:01.92: [ 4956]: --> [2:OK]
Dec 26 17:56:01.92: [ 4956]: RECV recv
EOP (no more pages or documents)
Dec 26 17:56:01.92: [ 4956]: <--
[9:AT+FRS=3D7\r]
Dec 26 17:56:01.93: [ 4956]: --> [5:ERROR]
Dec 26
17:56:01.93: [ 4956]: MODEM Command error
Dec 26 17:56:01.93: [ 4956]: RECV
FAX (00000018): recvq/fax00012.tif from 6913305099931, route to
<unspecified>, 0 pages in 0:21
Dec 26 17:56:01.93: [ 4956]: RECV FAX:
Failure to receive silence.
Dec 26 17:56:01.93: [ 4956]: <--
[9:AT+FTH=3D3\r]
Dec 26 17:56:03.64: [ 4956]: --> [7:CONNECT]
Dec 26
17:56:03.64: [ 4956]: <-- data [3]
Dec 26 17:56:03.64: [ 4956]: <--
data [2]
Dec 26 17:56:03.90: [ 4956]: --> [2:OK]
Dec 26 17:56:03.90: [
4956]: MODEM input buffering enabled
Dec 26 17:56:03.90: [ 4956]: RECV FAX
(00000018): session with 6913305099931 terminated abnormally: Failure to receive
silence.
Dec 26 17:56:03.90: [ 4956]: RECV FAX: bin/faxrcvd
"recvq/fax00012.tif" "ttyI0" "00000018" "Failure to receive silence." "CALLER
NUMBER: 6913303" "CALLER NUMBER: 6913303" ""
Dec 26 17:56:04.30: [ 4956]:
RECV FAX: end
Dec 26 17:56:04.30: [ 4956]: SESSION END
Es waere sehr
schoen, wenn mir jemand einen Tip geben koennte. Vielen Dank im
Voraus.
Uwe