27 Jan
2007
27 Jan
'07
7:55 a.m.
Hi,
Now that I've gotten numpy and scipy to work (thanks!), I can't get
matplotlib to display anything. I recall having problems with
opensuse's python and Tcl/Tk programs, like idle, in the past. I
installed python-idle and, python-tk from the 10.2 repo, and now idle
runs fine (beforehand, idle wasn't on the system). I then try to
following:
>> from pylab imort *
>> plot([1,2,3,4])
>> show()
From either idle or vanilla python from the shell, I
get nothing. A
window with the plot should be created. So this is a bit
mysterious.
Any thoughts?
Thanks,
David
---------------------------------------------------------------------
To unsubscribe, e-mail: opensuse-buildservice+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-buildservice+help(a)opensuse.org
1 Feb
1 Feb
5:53 a.m.
Folks,
Has anyone responded to this? If so I haven't gotten any. I think
something's setup weird with my gmail filter for opensuse-buildservice
since I've gotten other msgs, but not my initial posts or anything
since. If there has been a response perhaps someone would be kind
enough to email me personally rather than thru the list, partly to
diagnose this problem.
Thanks,
David
On 1/28/07, David Strozzi <david.strozzi(a)gmail.com> wrote:
Hmmm. That's odd. After sending the 2nd post and
you replying, all
three messages appeared. I'm using gmail (lovely conversations
layout) and a filter, so it's probably something on my end...
Thanks,
Dave
On 1/28/07, Patrick Shanahan <ptilopteri(a)gmail.com> wrote:
---------------------------------------------------------------------
To unsubscribe, e-mail: opensuse-buildservice+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-buildservice+help(a)opensuse.org
* David Strozzi <david.strozzi(a)gmail.com>
[01-28-07 15:12]:
[I posted this message on 26 Jan (California
time) and it never got
through...]
Yes, it did:
Date: Fri, 26 Jan 2007 22:55:33 -0800
From: David Strozzi <david.strozzi(a)gmail.com>
To: opensuse-buildservice(a)opensuse.org
Subject: [opensuse-buildservice] matplotlib and opensuse 10.2
X-Mailinglist: opensuse-buildservice
but it didn't get a "Message-ID" number ????
--
Patrick Shanahan Registered Linux User #207535
http://wahoo.no-ip.org @ http://counter.li.org
HOG # US1244711 Photo Album: http://wahoo.no-ip.org/gallery2
OpenSUSE Linux http://en.opensuse.org/
---------------------------------------------------------------------
To unsubscribe, e-mail: opensuse-buildservice+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-buildservice+help(a)opensuse.org
28 Jan
28 Jan
9:25 p.m.
New subject: [opensuse-buildservice] Fwd: matplotlib and opensuse 10.2
Hmmm. That's odd. After sending the 2nd post and you replying, all
three messages appeared. I'm using gmail (lovely conversations
layout) and a filter, so it's probably something on my end...
Thanks,
Dave
On 1/28/07, Patrick Shanahan <ptilopteri(a)gmail.com> wrote:
* David Strozzi <david.strozzi(a)gmail.com>
[01-28-07 15:12]:
---------------------------------------------------------------------
To unsubscribe, e-mail: opensuse-buildservice+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-buildservice+help(a)opensuse.org
[I posted this message on 26 Jan (California
time) and it never got
through...]
Yes, it did:
Date: Fri, 26 Jan 2007 22:55:33 -0800
From: David Strozzi <david.strozzi(a)gmail.com>
To: opensuse-buildservice(a)opensuse.org
Subject: [opensuse-buildservice] matplotlib and opensuse 10.2
X-Mailinglist: opensuse-buildservice
but it didn't get a "Message-ID" number ????
--
Patrick Shanahan Registered Linux User #207535
http://wahoo.no-ip.org @ http://counter.li.org
HOG # US1244711 Photo Album: http://wahoo.no-ip.org/gallery2
OpenSUSE Linux http://en.opensuse.org/
---------------------------------------------------------------------
To unsubscribe, e-mail: opensuse-buildservice+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-buildservice+help(a)opensuse.org
9:19 p.m.
New subject: [opensuse-buildservice] Fwd: matplotlib and opensuse 10.2
* David Strozzi <david.strozzi(a)gmail.com> [01-28-07 15:12]:
[I posted this message on 26 Jan (California time) and
it never got
through...]
Yes, it did:
Date: Fri, 26 Jan 2007 22:55:33 -0800
From: David Strozzi <david.strozzi(a)gmail.com>
To: opensuse-buildservice(a)opensuse.org
Subject: [opensuse-buildservice] matplotlib and opensuse 10.2
X-Mailinglist: opensuse-buildservice
but it didn't get a "Message-ID" number ????
--
Patrick Shanahan Registered Linux User #207535
http://wahoo.no-ip.org @ http://counter.li.org
HOG # US1244711 Photo Album: http://wahoo.no-ip.org/gallery2
OpenSUSE Linux http://en.opensuse.org/
---------------------------------------------------------------------
To unsubscribe, e-mail: opensuse-buildservice+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-buildservice+help(a)opensuse.org
9:11 p.m.
New subject: [opensuse-buildservice] Fwd: matplotlib and opensuse 10.2
[I posted this message on 26 Jan (California time) and it never got through...]
Hi,
Now that I've gotten numpy and scipy to work (thanks!), I can't get
matplotlib to display anything. I recall having problems with
opensuse's python and Tcl/Tk programs, like idle, in the past. I
installed python-idle and, python-tk from the 10.2 repo, and now idle
runs fine (beforehand, idle wasn't on the system). I then try to
following:
>> from pylab imort *
>> plot([1,2,3,4])
>> show()
From either idle or vanilla python from the shell, I
get nothing. A
window with the plot should be created. So this is a bit
mysterious.
Any thoughts?
Thanks,
David
---------------------------------------------------------------------
To unsubscribe, e-mail: opensuse-buildservice+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-buildservice+help(a)opensuse.org
5104
days inactive
5109
days old
buildservice@lists.opensuse.org
4 comments
2 participants
participants (2)
-
David Strozzi -
Patrick Shanahan