On Thu 16 Feb 2017 12:19:15 AM CST, Alexander Bergmann wrote:

Hi everyone,

I've ran into a problem where the wifi card of my Raspberry Pi 3 can not be initialized after I've executed mkinitrd.

I've used the latest JeOS Leap42.2 image.

openSUSE-Leap42.2-ARM-JeOS-raspberrypi3.aarch64-2017.02.02-Build1.5.raw.xz

When I start the image the WiFi card will be loaded without any problems.

...

brcmfmac: brcmf_sdio_drivestrengthinit: No SDIO Drive strength init done for chip 43430 rev 1 pmurev 24 brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: May 27 2016 00:13:38 version 7.45.41.26 (r640327) FWID 01-df77e4a7 brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code

After a simple mkinitrd the module cannot be loaded anymore.

...

brcmfmac_sdio: probe of mmc1:0001:1 failed with error -110 brcmfmac_sdio: probe of mmc1:0001:2 failed with error -110

I couldn't find out so far what caused this problem.

Anyone any hint/idea?

Ciao, Alex~

Hi I just followed the steps in the following archive message on a Leap 42.2 JeOS install (except I just used mkinitrd) https://lists.opensuse.org/opensuse-arm/2016-11/msg00018.html Wireless is up. -- Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890) openSUSE Leap 42.1|GNOME 3.16.2|4.1.36-44-default up 4 days 20:45, 3 users, load average: 0.18, 0.33, 0.23 CPU AMD Athlon(tm) II X4 635 @ 2.90GHz | GPU Nvidia GeForce 8800 GT -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org

Hi Malcolm! On Wed, Feb 15, 2017 at 06:35:07PM -0600, Malcolm wrote:

On Wed 15 Feb 2017 06:21:25 PM CST, Malcolm wrote:

...

On Thu 16 Feb 2017 12:19:15 AM CST, Alexander Bergmann wrote:

...

After a simple mkinitrd the module cannot be loaded anymore.

...

brcmfmac_sdio: probe of mmc1:0001:1 failed with error -110 brcmfmac_sdio: probe of mmc1:0001:2 failed with error -110

Hi I just followed the steps in the following archive message on a Leap 42.2 JeOS install (except I just used mkinitrd) https://lists.opensuse.org/opensuse-arm/2016-11/msg00018.html

Wireless is up.

Hi (again) One other thought, is the time/date configured? I've seen some funnies if it's not set, prefer to use ntp...

The change of /etc/dracut.conf.d/raspberrypi_modules.conf did the trick! -add_drivers+=" sdhci-iproc bcm2835-sdhost bcm2835_dma mmc_block " +add_drivers+=" bcm2835-sdhost bcm2835_dma mmc_block " Thanks for pointing in the right direction... Alex~ -- Alexander Bergmann , Security Engineer, GPG:9FFA4886 SUSE Linux GmbH, GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB 21284 (AG Nürnberg)

Am 17.02.2017 um 12:22 schrieb Freek de Kruijf :

Op donderdag 16 februari 2017 21:13:58 CET schreef Alexander Bergmann:

...

Hi Malcolm!

...

On Wed, Feb 15, 2017 at 06:35:07PM -0600, Malcolm wrote:

...

On Wed 15 Feb 2017 06:21:25 PM CST, Malcolm wrote:

...

On Thu 16 Feb 2017 12:19:15 AM CST, Alexander Bergmann wrote: After a simple mkinitrd the module cannot be loaded anymore.

...

brcmfmac_sdio: probe of mmc1:0001:1 failed with error -110 brcmfmac_sdio: probe of mmc1:0001:2 failed with error -110

Hi I just followed the steps in the following archive message on a Leap 42.2 JeOS install (except I just used mkinitrd) https://lists.opensuse.org/opensuse-arm/2016-11/msg00018.html

Wireless is up.

...

The change of /etc/dracut.conf.d/raspberrypi_modules.conf did the trick!

-add_drivers+=" sdhci-iproc bcm2835-sdhost bcm2835_dma mmc_block " +add_drivers+=" bcm2835-sdhost bcm2835_dma mmc_block "

Thanks for pointing in the right direction...

Alex~

My Tumbleweed version on RPi3 still does not have a wlan0. I tried the above, but bcm2835-sdhost is not available on my system. The current kernel is 4.9.6-1-default.

Yes, the driver for the second sd controller isn't in 4.9 yet :). It is in the leap kernel though. Alex -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org