Hi ,
I 'm trying to install SLES 8 on IBM e326 dual opteron system which has
SIL 3152A controller
Though SUSE does not provide drivers there are drivers posted by SIL.
The system just stops at initializing the SATA driver and does not complete the
procedure. The boot.msg is attached ..
Also here are the outputs of
cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: TEAC Model: FD-05PUB Rev: 1026
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: Model: Rev:
Type: <NULL> ANSI SCSI revision: ffffffff
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: QDI Model: USBDisk Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
and
cat /proc/scsi/sil
Driver for SiI 3112 to 6512 SATA RAID Controllers
Rev: 1.0.0.15, Date: Jun 13 2003 Time: 06:15:28
Memory (unique_id) at 0xFC103000, Irq 17
(Rk) Device(s) attached:
0: ST380013AS ( UDMA6 )
1: not attached
2: not attached
3: not attached
Raid Information
I know SLES 9 works out of the box ...
Any pointers will be great .
Thanks in advance
yogesh
--
Yogesh Bhanu
MIPS/IBI,
#56, GSF- National Research Center for Environment and Health,
Ingolstaedter Landstr. 1 ,
D-85764, Neuherberg, Germany
Tel: +49 89 3187 4217
Fax: +49 89 3187 3585
http://mips.gsf.de
<4>Linux version 2.4.19 (root@AMD64.suse.de) (gcc version 3.2.2 (SuSE Linux)) #1 Mon Mar 31 23:47:50 UTC 2003
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009b400 (usable)
<4> BIOS-e820: 000000000009b400 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 00000000fbf70000 (usable)
<4> BIOS-e820: 00000000fbf70000 - 00000000fbf7b000 (ACPI data)
<4> BIOS-e820: 00000000fbf7b000 - 00000000fbf80000 (ACPI NVS)
<4> BIOS-e820: 00000000fbf80000 - 00000000fc000000 (reserved)
<4> BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved)
<4> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
<4> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
<4>kernel direct mapping tables upto 10100000000 @ 8000-d000
<4>Scan SMP from 0000010000000000 for 1024 bytes.
<4>Scan SMP from 000001000009fc00 for 1024 bytes.
<4>Scan SMP from 00000100000f0000 for 65536 bytes.
<6>found SMP MP-table at 00000000000f7520
<4>hm, page 000f7000 reserved twice.
<4>hm, page 000f8000 reserved twice.
<4>hm, page 0009b000 reserved twice.
<4>hm, page 0009c000 reserved twice.
<4>On node 0 totalpages: 1032048
<4>zone(0): 4096 pages.
<4>zone(1): 1027952 pages.
<4>zone(2): 0 pages.
<6>ACPI: RSDP (v002 PTLTD ) @ 0x00000000000f74a0
<6>ACPI: XSDT (v001 PTLTD XSDT 01540.00000) @ 0x00000000fbf78c8f
<6>ACPI: FADT (v003 AMD HAMMER 01540.00000) @ 0x00000000fbf7ae0e
<6>ACPI: HPET (v001 AMD HAMMER 01540.00000) @ 0x00000000fbf7af02
<6>ACPI: MADT (v001 PTLTD APIC 01540.00000) @ 0x00000000fbf7af3a
<6>ACPI: SPCR (v001 PTLTD $UCRTBL$ 01540.00000) @ 0x00000000fbf7afb0
<6>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
<4>Processor #0 15:5 APIC version 16
<6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
<4>Processor #1 15:5 APIC version 16
<6>ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1])
<6>ACPI: LAPIC_NMI (acpi_id[0x01] polarity[0x1] trigger[0x1] lint[0x1])
<6>ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
<6>IOAPIC[0]: Assigned apic_id 2
<4>IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, IRQ 0-23
<6>ACPI: IOAPIC (id[0x03] address[0xfc000000] global_irq_base[0x18])
<6>IOAPIC[1]: Assigned apic_id 3
<4>IOAPIC[1]: apic_id 3, version 17, address 0xfc000000, IRQ 24-27
<6>ACPI: IOAPIC (id[0x04] address[0xfc001000] global_irq_base[0x1c])
<6>IOAPIC[2]: Assigned apic_id 4
<4>IOAPIC[2]: apic_id 4, version 17, address 0xfc001000, IRQ 28-31
<6>ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x1] trigger[0x1])
<6>acpi: HPET id: 0x102282a0 base: 0xfed00000
<6>Using ACPI (MADT) for SMP configuration information
<4>Building zonelist for node : 0
<4>Kernel command line: initrd=initrd ramdisk_size=65536 BOOT_IMAGE=linux SuSE=,120320007F,4B1FCFFF., vga=0x0317 expert=2
<4>Initializing CPU#0
<6>time.c: Detected 14.318180 MHz HPET timer.
<6>time.c: Detected 2193.503 MHz TSC timer.
<4>Console: colour dummy device 80x25
<4>Calibrating delay loop... 4377.80 BogoMIPS
<4>Memory: 4031744k/4128192k available (1713k kernel code, 96044k reserved, 1092k data, 156k init)
<6>Dentry cache hash table entries: 131072 (order: 9, 2097152 bytes)
<6>Inode cache hash table entries: 131072 (order: 9, 2097152 bytes)
<4>Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
<4>Buffer-cache hash table entries: 262144 (order: 9, 2097152 bytes)
<4>Page-cache hash table entries: 262144 (order: 9, 2097152 bytes)
<6>CPU: L1 I Cache: 64K (64 bytes/line/2 way), D cache 64K (64 bytes/line/2 way)
<6>CPU: L2 Cache: 1024K (64 bytes/line/8 way)
<6>Machine Check Reporting enabled for CPU#0
<4>POSIX conformance testing by UNIFIX
<6>testing NMI watchdog ... OK.
<4>ENABLING IO-APIC IRQs
<7>init IO_APIC IRQs
<7> IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23, 3-0, 3-1, 3-2, 3-3, 4-0, 4-1, 4-2, 4-3 not connected.
<6>..TIMER: vector=0x31 pin1=2 pin2=0
<7>number of MP IRQ sources: 16.
<7>number of IO-APIC #2 registers: 24.
<7>number of IO-APIC #3 registers: 4.
<7>number of IO-APIC #4 registers: 4.
<6>testing the IO APIC.......................
<4>
<7>IO APIC #2......
<7>.... register #00: 02000000
<7>....... : physical APIC id: 02
<7>.... register #01: 00170011
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 0
<7>....... : IO APIC version: 0011
<7>.... register #02: 02000000
<7>....... : arbitration: 02
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 000 00 1 0 0 0 0 0 0 00
<7> 01 001 01 0 0 0 0 0 1 1 39
<7> 02 001 01 0 0 0 0 0 1 1 31
<7> 03 001 01 0 0 0 0 0 1 1 41
<7> 04 001 01 0 0 0 0 0 1 1 49
<7> 05 001 01 0 0 0 0 0 1 1 51
<7> 06 001 01 0 0 0 0 0 1 1 59
<7> 07 001 01 0 0 0 0 0 1 1 61
<7> 08 001 01 0 0 0 0 0 1 1 69
<7> 09 001 01 0 0 0 0 0 1 1 71
<7> 0a 001 01 0 0 0 0 0 1 1 79
<7> 0b 001 01 0 0 0 0 0 1 1 81
<7> 0c 001 01 0 0 0 0 0 1 1 89
<7> 0d 001 01 0 0 0 0 0 1 1 91
<7> 0e 001 01 0 0 0 0 0 1 1 99
<7> 0f 001 01 0 0 0 0 0 1 1 A1
<7> 10 000 00 1 0 0 0 0 0 0 00
<7> 11 000 00 1 0 0 0 0 0 0 00
<7> 12 000 00 1 0 0 0 0 0 0 00
<7> 13 000 00 1 0 0 0 0 0 0 00
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<4>
<7>IO APIC #3......
<7>.... register #00: 03000000
<7>....... : physical APIC id: 03
<7>.... register #01: 00030011
<7>....... : max redirection entries: 0003
<7>....... : PRQ implemented: 0
<7>....... : IO APIC version: 0011
<7>.... register #02: 00000000
<7>....... : arbitration: 00
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 000 00 1 0 0 0 0 0 0 00
<7> 01 000 00 1 0 0 0 0 0 0 00
<7> 02 000 00 1 0 0 0 0 0 0 00
<7> 03 000 00 1 0 0 0 0 0 0 00
<4>
<7>IO APIC #4......
<7>.... register #00: 04000000
<7>....... : physical APIC id: 04
<7>.... register #01: 00030011
<7>....... : max redirection entries: 0003
<7>....... : PRQ implemented: 0
<7>....... : IO APIC version: 0011
<7>.... register #02: 00000000
<7>....... : arbitration: 00
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 000 00 1 0 0 0 0 0 0 00
<7> 01 000 00 1 0 0 0 0 0 0 00
<7> 02 000 00 1 0 0 0 0 0 0 00
<7> 03 000 00 1 0 0 0 0 0 0 00
<7>IRQ to pin mappings:
<7>IRQ0 -> 0:2
<7>IRQ1 -> 0:1
<7>IRQ3 -> 0:3
<7>IRQ4 -> 0:4
<7>IRQ5 -> 0:5
<7>IRQ6 -> 0:6
<7>IRQ7 -> 0:7
<7>IRQ8 -> 0:8
<7>IRQ9 -> 0:9
<7>IRQ10 -> 0:10
<7>IRQ11 -> 0:11
<7>IRQ12 -> 0:12
<7>IRQ13 -> 0:13
<7>IRQ14 -> 0:14
<7>IRQ15 -> 0:15
<6>.................................... done.
<4>Using local APIC timer interrupts.
<4>Detected 12.463 MHz APIC timer.
<6>cpu: 0, clocks: 1994093, slice: 997046
<6>CPU0T0:1994080,T1:997024,D:10,S:997046,C:1994093
<4>mtrr: v2.02 (20020716))
<6>ACPI: Subsystem revision 20020815
<6>PCI: Using configuration type 1
<6>ACPI: Interpreter enabled
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: System [ACPI] (supports S0 S1 S4 S5)
<6>ACPI: PCI Root Bridge [PCI0] (00:00)
<4>PCI: Probing PCI hardware (bus 00)
<3>Unknown bridge resource 2: assuming transparent
<3>Unknown bridge resource 0: assuming transparent
<3>Unknown bridge resource 2: assuming transparent
<3>Unknown bridge resource 0: assuming transparent
<3>Unknown bridge resource 1: assuming transparent
<3>Unknown bridge resource 2: assuming transparent
<4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 5 *10 11)
<4>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11, enabled at IRQ 7)
<4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 11, disabled)
<4>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 10 *11)
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.TP2P._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.G0PA._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.G0PB._PRT]
<6>PCI: Using configuration type 1
<6>PCI: Probing PCI hardware
<4>ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
<7>IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16)
<7>00:01:00[A] -> 2-16 -> vector 0xa9 -> IRQ 16
<7>IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17)
<7>00:01:00[B] -> 2-17 -> vector 0xb1 -> IRQ 17
<7>IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18)
<7>00:01:00[C] -> 2-18 -> vector 0xb9 -> IRQ 18
<7>IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19)
<7>00:01:00[D] -> 2-19 -> vector 0xc1 -> IRQ 19
<7>Pin 2-16 already programmed
<7>Pin 2-17 already programmed
<7>Pin 2-18 already programmed
<7>Pin 2-19 already programmed
<7>Pin 2-16 already programmed
<7>IOAPIC[1]: Set PCI routing entry (3-0 -> 0xc9 -> IRQ 24)
<7>00:02:01[A] -> 3-0 -> vector 0xc9 -> IRQ 24
<7>IOAPIC[1]: Set PCI routing entry (3-1 -> 0xd1 -> IRQ 25)
<7>00:02:01[B] -> 3-1 -> vector 0xd1 -> IRQ 25
<7>IOAPIC[1]: Set PCI routing entry (3-2 -> 0xd9 -> IRQ 26)
<7>00:02:02[A] -> 3-2 -> vector 0xd9 -> IRQ 26
<7>IOAPIC[1]: Set PCI routing entry (3-3 -> 0xe1 -> IRQ 27)
<7>00:02:02[B] -> 3-3 -> vector 0xe1 -> IRQ 27
<7>Pin 3-0 already programmed
<7>Pin 3-1 already programmed
<7>IOAPIC[2]: Set PCI routing entry (4-0 -> 0xe9 -> IRQ 28)
<7>00:03:03[A] -> 4-0 -> vector 0xe9 -> IRQ 28
<7>IOAPIC[2]: Set PCI routing entry (4-1 -> 0x32 -> IRQ 29)
<7>00:03:03[B] -> 4-1 -> vector 0x32 -> IRQ 29
<7>IOAPIC[2]: Set PCI routing entry (4-2 -> 0x3a -> IRQ 30)
<7>00:03:03[C] -> 4-2 -> vector 0x3a -> IRQ 30
<7>IOAPIC[2]: Set PCI routing entry (4-3 -> 0x42 -> IRQ 31)
<7>00:03:03[D] -> 4-3 -> vector 0x42 -> IRQ 31
<7>Pin 4-1 already programmed
<7>Pin 4-2 already programmed
<7>Pin 4-3 already programmed
<7>Pin 4-0 already programmed
<4>PCI: No IRQ known for interrupt pin D of device 00:07.2 - using IRQ 255
<6>Linux agpgart interface v0.99 (c) Jeff Hartmann
<6>agpgart: Maximum main memory to use for agp memory: 3868M
<7>agpgart: no supported devices found.
<6>PCI-DMA: Disabling IOMMU.
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<4>Starting kswapd
<4>bigpage subsystem: allocated 0 bigpages (=0MB).
<4>kinoded started
<5>VFS: Diskquotas version dquot_6.5.0 initialized
<5>aio_setup: num_physpages = 258012
<5>aio_setup: sizeof(struct page) = 88
<4>IA32 emulation $Id: sys_ia32.c,v 1.53 2003/03/12 09:45:06 ak Exp $
<6>ACPI: Power Button (FF) [PWRF]
<6>ACPI: Processor [CPU0] (supports C1)
<6>ACPI: Processor [CPU1] (supports C1)
<6>vesafb: framebuffer at 0xfd000000, mapped to 0xffffff0000016000, size 8128k
<6>vesafb: mode is 1024x768x16, linelength=2048, pages=4
<6>vesafb: scrolling: redraw
<6>vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
<4>mtrr: type mismatch for fd000000,400000 old: uncachable new: write-combining
<4>mtrr: type mismatch for fd000000,200000 old: uncachable new: write-combining
<4>mtrr: type mismatch for fd000000,100000 old: uncachable new: write-combining
<4>mtrr: type mismatch for fd000000,80000 old: uncachable new: write-combining
<4>mtrr: type mismatch for fd000000,40000 old: uncachable new: write-combining
<4>mtrr: type mismatch for fd000000,20000 old: uncachable new: write-combining
<4>mtrr: type mismatch for fd000000,10000 old: uncachable new: write-combining
<4>mtrr: type mismatch for fd000000,8000 old: uncachable new: write-combining
<4>mtrr: type mismatch for fd000000,4000 old: uncachable new: write-combining
<4>mtrr: type mismatch for fd000000,2000 old: uncachable new: write-combining
<4>mtrr: type mismatch for fd000000,1000 old: uncachable new: write-combining
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x800 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x400 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x200 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x100 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x80 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x40 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x20 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x10 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x8 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x4 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x2 base: 0xfd000000
<4>mtrr: size and base must be multiples of 4 kiB
<4>mtrr: size: 0x1 base: 0xfd000000
<6>Looking for splash picture..... found (1024x768, 14583 bytes).
<4>Console: switching to colour frame buffer device 127x39
<6>fb0: VESA VGA frame buffer device
<4>initialize_kbd: Keyboard reset failed, no ACK
<4>pty: 256 Unix98 ptys configured
<6>Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>Real Time Clock Driver v1.10e
<6>Uniform Multi-Platform E-IDE driver Revision: 6.31
<4>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<4>AMD_IDE: IDE controller on PCI bus 00 dev 39
<4>AMD_IDE: chipset revision 3
<4>AMD_IDE: not 100% native mode: will probe irqs later
<4>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>AMD74xx: AMD-8111 (rev 03) IDE UDMA100 controller on pci00:07.1
<4> ide0: BM-DMA at 0x1020-0x1027, BIOS settings: hda:pio, hdb:pio
<4> ide1: BM-DMA at 0x1028-0x102f, BIOS settings: hdc:DMA, hdd:pio
<4>hdc: HL-DT-STDVD-ROM GDR8082N, ATAPI CD/DVD-ROM drive
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>hdc: ATAPI 24X DVD-ROM drive, 256kB Cache
<6>Uniform CD-ROM driver Revision: 3.12
<4>ide-floppy driver 0.99.newide
<4>floppy0: no floppy controllers found
<4>RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
<6>loop: loaded (max 16 devices)
<4>ide-floppy driver 0.99.newide
<6>SCSI subsystem driver Revision: 1.00
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<6>IP: routing cache hash table of 32768 buckets, 256Kbytes
<6>TCP: Hash tables configured (established 262144 bind 65536)
<6>Linux IP multicast router 0.06 plus PIM-SM
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<5>RAMDISK: Compressed image found at block 0
<4>VFS: Mounted root (minix filesystem).
<6>Non-volatile memory driver v1.1
<6>usb.c: registered new driver usbdevfs
<6>usb.c: registered new driver hub
<6>usb-ohci.c: USB OHCI at membase 0xffffff0000819000, IRQ 19
<6>usb-ohci.c: usb-01:00.0, PCI device 1022:7464
<6>usb.c: new USB bus registered, assigned bus number 1
<6>hub.c: USB hub found
<6>hub.c: 3 ports detected
<6>usb-ohci.c: USB OHCI at membase 0xffffff000081b000, IRQ 19
<6>usb-ohci.c: usb-01:00.1, PCI device 1022:7464
<6>usb.c: new USB bus registered, assigned bus number 2
<6>hub.c: USB hub found
<6>hub.c: 3 ports detected
<6>hub.c: USB new device connect on bus1/1, assigned device number 2
<4>usb.c: USB device 2 (vend/prod 0x624/0x296) is not claimed by any active driver.
<6>hub.c: USB new device connect on bus2/2, assigned device number 2
<4>usb.c: USB device 2 (vend/prod 0x644/0x0) is not claimed by any active driver.
<6>usb.c: registered new driver hiddev
<6>usb.c: registered new driver hid
<6>input0: USB HID v1.10 Keyboard [Avocent IBM 73P5832] on usb1:2.0
<6>input1: USB HID v1.10 Mouse [Avocent IBM 73P5832] on usb1:2.1
<6>hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik
participants (1)
-
Yogesh Bhanu