Mailinglist Archive: opensuse (621 mails)

< Previous Next >
[opensuse] Dead disk
Hi,

My only 3 TB Seagate disk died suddenly, at 19447 hours of use. Smartctl was
perfect one day, thousand of bad sectors the next day. Report attached.

I bought a new disk and tried dd_rhelp to try recover some. It coredumped after
a while. So I switched to ddrescue instead, which did finished - but it
recovered less than 1%.



Telcontar:~/Rescate_sde # time ddrescue --force /dev/sdf /dev/sde mapfile
GNU ddrescue 1.23
Press Ctrl-C to interrupt
ipos: 3000 GB, non-trimmed: 0 B, current rate: 0 B/s
opos: 3000 GB, non-scraped: 0 B, average rate: 270 kB/s
non-tried: 0 B, bad-sector: 2975 GB, error rate: 15374 kB/s
rescued: 24785 MB, bad areas: 6, run time: 1d 1h 29m
pct rescued: 0.82%, read errors:5857531191, remaining time: n/a
time since last successful read: 1d 53m 36s
Finished

real 1529m30.632s
user 135m6.844s
sys 750m55.166s
Telcontar:~/Rescate_sde #


On syslog, tons of errors - I copy the end of it:


<1.4> 2019-06-06 17:47:33 Telcontar udisksd 4343 - - Error performing
housekeeping for drive
/org/freedesktop/UDisks2/drives/ST3000DM001_1CH166_Z1F42M6N: Error updating
SMART data: Error sending ATA command CHECK POWER MODE: Unexpected
sense data returned:#0120000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 ................#0120010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 ................#012 (g-io-error-quark, 0)

<1.4> 2019-06-06 17:57:33 Telcontar udisksd 4343 - - Error performing
housekeeping for drive
/org/freedesktop/UDisks2/drives/ST3000DM001_1CH166_Z1F42M6N: Error updating
SMART data: Error sending ATA command CHECK POWER MODE: Unexpected
sense data returned:#0120000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 ................#0120010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 ................#012 (g-io-error-quark, 0)
<0.6> 2019-06-06 17:57:33 Telcontar kernel - - - [156725.304768] sd 7:0:0:0:
[sdf] tag#17 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
<0.6> 2019-06-06 17:57:33 Telcontar kernel - - - [156725.304772] sd 7:0:0:0:
[sdf] tag#17 CDB: ATA command pass through(16) 85 06 20 00 00 00 00 00 00 00 00
00 00 00 e5 00

<1.4> 2019-06-06 18:07:33 Telcontar udisksd 4343 - - Error performing
housekeeping for drive
/org/freedesktop/UDisks2/drives/ST3000DM001_1CH166_Z1F42M6N: Error updating
SMART data: Error sending ATA command CHECK POWER MODE: Unexpected
sense data returned:#0120000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 ................#0120010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 ................#012 (g-io-error-quark, 0)
<0.6> 2019-06-06 18:07:33 Telcontar kernel - - - [157325.363715] sd 7:0:0:0:
[sdf] tag#19 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
<0.6> 2019-06-06 18:07:33 Telcontar kernel - - - [157325.363719] sd 7:0:0:0:
[sdf] tag#19 CDB: ATA command pass through(16) 85 06 20 00 00 00 00 00 00 00 00
00 00 00 e5 00

<1.4> 2019-06-06 18:17:34 Telcontar udisksd 4343 - - Error performing
housekeeping for drive
/org/freedesktop/UDisks2/drives/ST3000DM001_1CH166_Z1F42M6N: Error updating
SMART data: Error sending ATA command CHECK POWER MODE: Unexpected
sense data returned:#0120000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 ................#0120010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 ................#012 (g-io-error-quark, 0)
<0.6> 2019-06-06 18:17:34 Telcontar kernel - - - [157925.740068] sd 7:0:0:0:
[sdf] tag#21 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
<0.6> 2019-06-06 18:17:34 Telcontar kernel - - - [157925.740072] sd 7:0:0:0:
[sdf] tag#21 CDB: ATA command pass through(16) 85 06 20 00 00 00 00 00 00 00 00
00 00 00 e5 00

<1.4> 2019-06-06 18:27:34 Telcontar udisksd 4343 - - Error performing
housekeeping for drive
/org/freedesktop/UDisks2/drives/ST3000DM001_1CH166_Z1F42M6N: Error updating
SMART data: Error sending ATA command CHECK POWER MODE: Unexpected sense data
returned:#0120000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................#0120010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................#012 (g-io-error-quark, 0)
<0.6> 2019-06-06 18:27:34 Telcontar kernel - - - [158526.004939] sd 7:0:0:0:
[sdf] tag#23 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
<0.6> 2019-06-06 18:27:34 Telcontar kernel - - - [158526.004944] sd 7:0:0:0:
[sdf] tag#23 CDB: ATA command pass through(16) 85 06 20 00 00 00 00 00 00 00 00
00 00 00 e5 00

<1.4> 2019-06-06 18:37:33 Telcontar udisksd 4343 - - Error performing
housekeeping for drive
/org/freedesktop/UDisks2/drives/ST3000DM001_1CH166_Z1F42M6N: Error updating
SMART data: Error sending ATA command CHECK POWER MODE: Unexpected sense data
returned:#0120000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................#0120010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................#012 (g-io-error-quark, 0)
<0.6> 2019-06-06 18:37:33 Telcontar kernel - - - [159125.573187] sd 7:0:0:0:
[sdf] tag#25 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
<0.6> 2019-06-06 18:37:33 Telcontar kernel - - - [159125.573191] sd 7:0:0:0:
[sdf] tag#25 CDB: ATA command pass through(16) 85 06 20 00 00 00 00 00 00 00 00
00 00 00 e5 00


I attach what I think is the start section of the log when I connected the disk.


How can a disk get that amount of bad data? The surface can not go bad entirely
except for a few megabytes at the start of the disk, it has to be the
electronics.

Any ideas?

I want to know if it is possible to power cycle the disk, then use ddrescue
again in some form so that it ignores previously read sectors and goes for the
bad areas directly.

The data is just multimedia, no big deal - I hope - so I'm mostly playing with
the disk. Apparently I don't have any other 3TB unit (I know they were bad, but
hey, this unit is years old) to switch the board. I do have a 2TB unit with
true surface defects.

--
Cheers / Saludos,

Carlos E. R.
(from 15.0 x86_64 at Telcontar)
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.12.14-lp151.27-default] (SUSE RPM)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST3000DM001-1CH166
Serial Number: Z1F42M6N
LU WWN Device Id: 5 000c50 065297c3e
Firmware Version: CC27
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sun Jun 2 11:15:31 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 332) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 115 099 006 Pre-fail Always
- 87743464
3 Spin_Up_Time 0x0003 095 093 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always
- 2401
5 Reallocated_Sector_Ct 0x0033 089 089 010 Pre-fail Always
- 13904
7 Seek_Error_Rate 0x000f 058 058 030 Pre-fail Always
- 124577919351
9 Power_On_Hours 0x0032 078 078 000 Old_age Always
- 19447
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always
- 2324
183 Runtime_Bad_Block 0x0032 098 098 000 Old_age Always
- 2
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 071 071 000 Old_age Always
- 28 30 30
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 066 056 045 Old_age Always
- 34 (Min/Max 34/36)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 93
193 Load_Cycle_Count 0x0032 007 007 000 Old_age Always
- 186842
194 Temperature_Celsius 0x0022 034 044 000 Old_age Always
- 34 (0 13 0 0 0)
197 Current_Pending_Sector 0x0012 001 001 000 Old_age Always
- 21344
198 Offline_Uncorrectable 0x0010 001 001 000 Old_age Offline
- 21344
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 4
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline
- 5309h+12m+33.571s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline
- 90692687964
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline
- 20862873710

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Extended offline Interrupted (host reset) 00% 19442 -
# 2 Short offline Completed without error 00% 19415 -
# 3 Short offline Completed without error 00% 19396 -
# 4 Short offline Completed without error 00% 19372 -
# 5 Short offline Completed without error 00% 19352 -
# 6 Short offline Completed without error 00% 19336 -
# 7 Short offline Completed without error 00% 19320 -
# 8 Short offline Completed without error 00% 19307 -
# 9 Short offline Completed without error 00% 19291 -
#10 Short offline Completed without error 00% 19276 -
#11 Short offline Completed without error 00% 19259 -
#12 Short offline Completed without error 00% 19240 -
#13 Short offline Completed without error 00% 19229 -
#14 Short offline Completed without error 00% 19213 -
#15 Short offline Completed without error 00% 19199 -
#16 Short offline Completed without error 00% 19183 -
#17 Short offline Completed without error 00% 19169 -
#18 Short offline Completed without error 00% 19168 -
#19 Short offline Completed without error 00% 19154 -
#20 Extended offline Interrupted (host reset) 90% 19141 -
#21 Short offline Completed without error 00% 19136 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

< Previous Next >