Mailinglist Archive: opensuse (626 mails)

< Previous Next >
Re: [opensuse] Login weirdness
  • From: Michael Fischer <michael@xxxxxxxx>
  • Date: Fri, 2 Nov 2018 10:27:03 -0400
  • Message-id: <20181102142703.bxqlcsskdgn7q4vj@blinkenlights>
On Thu, Nov 01, Carlos E. R. wrote:
On 01/11/2018 16.07, Michael Fischer wrote:

smartctl in this case.

Any particular suggestions with this one? Anything which can be run
from the NOT-rescue disk?

smartctl --test=short /dev/sdX

Replace X with the pro

smartctl -a /dev/sdX

and read. Then do

smartctl --test=long /dev/sdX

and wait some hours as told. Then read the results as before.

If on doubt about the meaning, post the output here.

Thanks much.

I append the output of `smartctl -a /dev/sda`. I meant to
run the --test=long last night, but fell asleep without triggering it... (bah)

I note that `smartctl -a` basically said "PASSED" but that there were a few
read errors. I've no idea what (more) to make of them.

FWIW, I realized that /dev/sda is my /home and /tmp on rust, not my
/ on an SSD, so it is perhaps _less_ likely to be the cause of my login
weirdness (I hope), and more amenable to a clean reinstall/upgrade.



smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.14.6-1.g45f120a-default] (SUSE
RPM)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST1000DM003-1SB102
Serial Number: Z9ACC0MX
LU WWN Device Id: 5 000c50 0a28684ad
Firmware Version: CC43
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Nov 1 19:26:17 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 38) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 106) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x1085) SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 074 063 006 Pre-fail Always
- 26493824
3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always
- 46
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000f 077 060 045 Pre-fail Always
- 57728258
9 Power_On_Hours 0x0032 092 092 000 Old_age Always
- 7752
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
- 41
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always
- 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 099 099 000 Old_age Always
- 1 1 1
189 High_Fly_Writes 0x003a 099 099 000 Old_age Always
- 1
190 Airflow_Temperature_Cel 0x0022 060 050 040 Old_age Always
- 40 (Min/Max 30/41)
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always
- 363
194 Temperature_Celsius 0x0022 040 016 000 Old_age Always
- 40 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 008 004 000 Old_age Always
- 26493824
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 16
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline
- 16
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline
- 7716h+03m+29.370s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline
- 6351787553
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline
- 352717284

SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1 occurred at disk power-on lifetime: 7752 hours (323 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown
state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 00 00 00 Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
00 00 00 00 00 00 00 ff 2d+03:57:39.774 NOP [Abort queued commands]
b0 d4 00 81 4f c2 00 00 2d+03:57:18.107 SMART EXECUTE OFF-LINE IMMEDIATE
b0 d0 01 00 4f c2 00 00 2d+03:57:18.000 SMART READ DATA
ec 00 01 00 00 00 00 00 2d+03:57:17.991 IDENTIFY DEVICE
ec 00 01 00 00 00 00 00 2d+03:57:17.990 IDENTIFY DEVICE

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short captive Interrupted (host reset) 60% 7752 -
# 2 Short offline Completed without error 00% 7752 -
# 3 Extended offline Completed: read failure 50% 7136
1001593016
# 4 Extended offline Completed: read failure 50% 6296
1001593016
# 5 Extended offline Completed: read failure 50% 5624
1001593016
# 6 Extended offline Completed: read failure 50% 4784
1001593016
# 7 Extended offline Completed: read failure 50% 4112
1001593016
# 8 Extended offline Completed: read failure 50% 3440
1001593016
# 9 Extended offline Completed: read failure 50% 2600
1001593016
#10 Extended offline Completed: read failure 50% 1929
1001593016
#11 Extended offline Completed: read failure 50% 1257
1021004240
#12 Extended offline Completed: read failure 50% 585
1001593008
#13 Short offline Completed without error 00% 0 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.





Michael
--
Michael Fischer
michael@xxxxxxxx

--
To unsubscribe, e-mail: opensuse+unsubscribe@xxxxxxxxxxxx
To contact the owner, e-mail: opensuse+owner@xxxxxxxxxxxx

< Previous Next >
Follow Ups