Mailinglist Archive: opensuse (924 mails)

< Previous Next >
[opensuse] wifi problems
I'm running 12.2 but haven't tried any previous versions. I have a Linksys-N router, and an Asus USB-N13 wireless adapter in a mini-ATX case with an Intel DH77DF MB. As long as I'm in the same room as the router all works fine. As soon as I install the box in any other room, I can't connect to the access point (router).

My wife is running an HP laptop (Windows-7) and can go anywhere in the house and get 3-4 bars on her signal quality meter. Why can't I? Attached is my dmesg output when not in the same room as the router.

While in the same room as the router:

# iwconfig wlan0
wlan0 IEEE 802.11bgn ESSID:"linksys"
Mode:Managed Frequency:2.432 GHz Access Point: 00:18:F8:FF:72:D5
Bit Rate=18 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr=2347 B Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=68/70 Signal level=-42 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0


# ifconfig wlan0

wlan0 Link encap:Ethernet HWaddr 10:BF:48:FB:C9:D1
inet addr:172.16.10.101 Bcast:172.16.10.255 Mask:255.255.255.0
inet6 addr: fe80::12bf:48ff:fefb:c9d1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:404 errors:0 dropped:0 overruns:0 frame:0
TX packets:362 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:119068 (116.2 Kb) TX bytes:102049 (99.6 Kb)


While out of the same room as the router:

#iwconfig

wlan0 IEEE 802.11bgn ESSID:"linksys"
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm

Retry long limit:7 RTS thr=2347 B Fragment thr:off

Encryption key:off

Power Management:off

#ifconfig wlan0

wlan0 Link encap:Ethernet HWaddr 10:BF:48:FB:C9:D1
inet addr:172.16.10.101 Bcast:172.16.10.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

Any help appreciated.
Regards
Mark
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.6.2 (root@geexbox) (gcc version 4.7.1 20120723
[gcc-4_7-branch revision 189773] (SUSE Linux) ) #1 SMP PREEMPT Fri Oct 19
01:21:55 EDT 2012
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x0000000040003fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000040004000-0x0000000040004fff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000040005000-0x00000000d9e5ffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d9e60000-0x00000000da25bfff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000da25c000-0x00000000da267fff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000da268000-0x00000000da2f3fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000da2f4000-0x00000000da2f9fff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000da2fa000-0x00000000da37bfff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000da37c000-0x00000000da40dfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000da40e000-0x00000000da6a2fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000da6a3000-0x00000000da6a3fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000da6a4000-0x00000000da6e6fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000da6e7000-0x00000000daffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000db800000-0x00000000df9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021f5fffff] usable
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] DMI 2.7 present.
[ 0.000000] DMI: /DH77DF, BIOS
KCH7710H.86A.0095.2012.0608.1754 06/08/2012
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0xdb000 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask E00000000 write-back
[ 0.000000] 1 base 200000000 mask FE0000000 write-back
[ 0.000000] 2 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 3 base 0DC000000 mask FFC000000 uncachable
[ 0.000000] 4 base 0DB800000 mask FFF800000 uncachable
[ 0.000000] 5 base 21F800000 mask FFF800000 uncachable
[ 0.000000] 6 base 21F600000 mask FFFE00000 uncachable
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: update [mem 0xdb800000-0xffffffff] usable ==> reserved
[ 0.000000] found SMP MP-table at [mem 0x000fd730-0x000fd73f] mapped at
[c00fd730]
[ 0.000000] initial memory mapped: [mem 0x00000000-0x00bfffff]
[ 0.000000] Base memory trampoline at [c0099000] 99000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x377fdfff]
[ 0.000000] [mem 0x00000000-0x003fffff] page 4k
[ 0.000000] [mem 0x00400000-0x373fffff] page 2M
[ 0.000000] [mem 0x37400000-0x377fdfff] page 4k
[ 0.000000] kernel direct mapping tables up to 0x377fdfff @ [mem
0x00bfa000-0x00bfffff]
[ 0.000000] RAMDISK: [mem 0x1e6aa000-0x1ffeffff]
[ 0.000000] ACPI: RSDP 000f0490 00024 (v02 INTEL)
[ 0.000000] ACPI: XSDT da25c070 00064 (v01 INTEL DH77DF 0000005F AMI
00010013)
[ 0.000000] ACPI: FACP da265db8 000F4 (v04 INTEL DH77DF 0000005F AMI
00010013)
[ 0.000000] ACPI: DSDT da25c168 09C49 (v02 INTEL DH77DF 0000005F INTL
20051117)
[ 0.000000] ACPI: FACS da40cf80 00040
[ 0.000000] ACPI: APIC da265eb0 00072 (v03 INTEL DH77DF 0000005F AMI
00010013)
[ 0.000000] ACPI: FPDT da265f28 00044 (v01 INTEL DH77DF 0000005F AMI
00010013)
[ 0.000000] ACPI: MCFG da265f70 0003C (v01 INTEL DH77DF 0000005F MSFT
00000097)
[ 0.000000] ACPI: HPET da265fb0 00038 (v01 INTEL DH77DF 0000005F AMI.
00000005)
[ 0.000000] ACPI: SSDT da265fe8 0036D (v01 INTEL DH77DF 0000005F INTL
20091112)
[ 0.000000] ACPI: SSDT da266358 009AA (v01 INTEL DH77DF 0000005F INTL
20051117)
[ 0.000000] ACPI: SSDT da266d08 00A92 (v01 INTEL DH77DF 0000005F INTL
20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 2616MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00010000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x377fdfff]
[ 0.000000] HighMem [mem 0x377fe000-0xdaffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x0009cfff]
[ 0.000000] node 0: [mem 0x00100000-0x1fffffff]
[ 0.000000] node 0: [mem 0x20200000-0x40003fff]
[ 0.000000] node 0: [mem 0x40005000-0xd9e5ffff]
[ 0.000000] node 0: [mem 0xda2fa000-0xda37bfff]
[ 0.000000] node 0: [mem 0xda6a3000-0xda6a3fff]
[ 0.000000] node 0: [mem 0xda6e7000-0xdaffffff]
[ 0.000000] On node 0 totalpages: 894344
[ 0.000000] free_area_init_node: node 0, pgdat c0894340, node_mem_map
f5c9d200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3949 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 220974 pages, LIFO batch:31
[ 0.000000] HighMem zone: 5233 pages used for memmap
[ 0.000000] HighMem zone: 662412 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000020200000
[ 0.000000] e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4
nr_node_ids:1
[ 0.000000] PERCPU: Embedded 12 pages/cpu @f5c5b000 s26944 r0 d22208 u49152
[ 0.000000] pcpu-alloc: s26944 r0 d22208 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 887335
[ 0.000000] Kernel command line:
root=/dev/disk/by-id/ata-INTEL_SSDSC2CW060A3_CVCV205106EB060AGN-part4
video=1024x768
resume=/dev/disk/by-id/ata-INTEL_SSDSC2CW060A3_CVCV205106EB060AGN-part3
splash=silent quiet vga=0x37e
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Initializing CPU#0
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Initializing HighMem for node 0 (000377fe:000db000)
[ 0.000000] Memory: 3514568k/3588096k available (4577k kernel code, 62808k
reserved, 2220k data, 452k init, 2670580k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc08a4000 - 0xc0915000 ( 452 kB)
[ 0.000000] .data : 0xc0678452 - 0xc08a3800 (2220 kB)
[ 0.000000] .text : 0xc0200000 - 0xc0678452 (4577 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor
mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4,
Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:2304 nr_irqs:712 16
[ 0.000000] CPU 0 irqstacks, hard=f5408000 soft=f540a000
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.003333] tsc: Detected 3392.321 MHz processor
[ 0.000001] Calibrating delay loop (skipped), value calculated using timer
frequency.. 6787.33 BogoMIPS (lpj=11307736)
[ 0.000002] pid_max: default: 32768 minimum: 301
[ 0.000015] Security Framework initialized
[ 0.000023] AppArmor: AppArmor initialized
[ 0.000028] Mount-cache hash table entries: 512
[ 0.000134] Initializing cgroup subsys net_cls
[ 0.000135] Initializing cgroup subsys blkio
[ 0.000152] CPU: Physical Processor ID: 0
[ 0.000153] CPU: Processor Core ID: 0
[ 0.000155] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.000155] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.000685] mce: CPU supports 9 MCE banks
[ 0.000695] CPU0: Thermal monitoring enabled (TM1)
[ 0.000701] process: using mwait in idle threads
[ 0.000705] Last level iTLB entries: 4KB 512, 2MB 0, 4MB 0
[ 0.000705] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
[ 0.000705] tlb_flushall_shift is 0x1
[ 0.001265] ACPI: Core revision 20120711
[ 0.007307] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.007722] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.040630] smpboot: CPU0: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz stepping
09
[ 0.146598] Performance Events: PEBS fmt1+, 16-deep LBR, IvyBridge events,
Intel PMU driver.
[ 0.146602] ... version: 3
[ 0.146603] ... bit width: 48
[ 0.146604] ... generic registers: 8
[ 0.146604] ... value mask: 0000ffffffffffff
[ 0.146605] ... max period: 000000007fffffff
[ 0.146606] ... fixed-purpose events: 3
[ 0.146606] ... event mask: 00000007000000ff
[ 0.193137] CPU 1 irqstacks, hard=f54a0000 soft=f54a2000
[ 0.203364] Initializing CPU#1
[ 0.193139] smpboot: Booting Node 0, Processors #1
[ 0.219726] CPU 2 irqstacks, hard=f54b6000 soft=f54b8000
[ 0.229896] Initializing CPU#2
[ 0.219730] #2
[ 0.246315] CPU 3 irqstacks, hard=f54d0000 soft=f54d2000
[ 0.246319] #3 OK
[ 0.256585] Initializing CPU#3
[ 0.260020] Brought up 4 CPUs
[ 0.260022] smpboot: Total of 4 processors activated (27149.34 BogoMIPS)
[ 0.262485] devtmpfs: initialized
[ 0.262620] PM: Registering ACPI NVS region [mem 0xda37c000-0xda40dfff]
(598016 bytes)
[ 0.262625] PM: Registering ACPI NVS region [mem 0xda6a4000-0xda6e6fff]
(274432 bytes)
[ 0.262678] dummy:
[ 0.262708] RTC time: 5:37:47, date: 10/19/12
[ 0.262731] NET: Registered protocol family 16
[ 0.302916] ACPI: bus type pci registered
[ 0.302960] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem
0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.302962] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.302963] PCI: Using MMCONFIG for extended config space
[ 0.302964] PCI: Using configuration type 1 for base access
[ 0.303401] bio: create slab <bio-0> at 0
[ 0.303437] ACPI: Added _OSI(Module Device)
[ 0.303438] ACPI: Added _OSI(Processor Device)
[ 0.303438] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.303439] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.304769] ACPI: EC: Look up EC in DSDT
[ 0.306286] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.316839] ACPI: SSDT da294018 0083B (v01 PmRef Cpu0Cst 00003001 INTL
20051117)
[ 0.317175] ACPI: Dynamic OEM Table Load:
[ 0.317177] ACPI: SSDT (null) 0083B (v01 PmRef Cpu0Cst 00003001 INTL
20051117)
[ 0.326301] ACPI: SSDT da295a98 00303 (v01 PmRef ApIst 00003000 INTL
20051117)
[ 0.326666] ACPI: Dynamic OEM Table Load:
[ 0.326668] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL
20051117)
[ 0.336457] ACPI: SSDT da29ac18 00119 (v01 PmRef ApCst 00003000 INTL
20051117)
[ 0.336795] ACPI: Dynamic OEM Table Load:
[ 0.336797] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL
20051117)
[ 0.350184] ACPI: Interpreter enabled
[ 0.350189] ACPI: (supports S0 S3 S4 S5)
[ 0.350201] ACPI: Using IOAPIC for interrupt routing
[ 0.354179] ACPI: Power Resource [FN00] (off)
[ 0.354229] ACPI: Power Resource [FN01] (off)
[ 0.354276] ACPI: Power Resource [FN02] (off)
[ 0.354324] ACPI: Power Resource [FN03] (off)
[ 0.354371] ACPI: Power Resource [FN04] (off)
[ 0.354729] ACPI: No dock devices found.
[ 0.354732] PCI: Using host bridge windows from ACPI; if necessary, use
"pci=nocrs" and report a bug
[ 0.354964] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.355294] PCI host bridge to bus 0000:00
[ 0.355296] pci_bus 0000:00: busn_res: [bus 00-3e] is inserted under domain
[bus 00-ff]
[ 0.355297] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.355299] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.355300] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.355301] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.355302] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[ 0.355303] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[ 0.355304] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[ 0.355305] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[ 0.355306] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[ 0.355307] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[ 0.355309] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfeafffff]
[ 0.355314] pci 0000:00:00.0: [8086:0150] type 00 class 0x060000
[ 0.355348] pci 0000:00:02.0: [8086:0162] type 00 class 0x030000
[ 0.355356] pci 0000:00:02.0: reg 10: [mem 0xf7800000-0xf7bfffff 64bit]
[ 0.355360] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.355363] pci 0000:00:02.0: reg 20: [io 0xf000-0xf03f]
[ 0.355406] pci 0000:00:14.0: [8086:1e31] type 00 class 0x0c0330
[ 0.355426] pci 0000:00:14.0: reg 10: [mem 0xf7d20000-0xf7d2ffff 64bit]
[ 0.355490] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.355510] pci 0000:00:16.0: [8086:1e3a] type 00 class 0x078000
[ 0.355531] pci 0000:00:16.0: reg 10: [mem 0xf7d37000-0xf7d3700f 64bit]
[ 0.355602] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.355629] pci 0000:00:19.0: [8086:1503] type 00 class 0x020000
[ 0.355645] pci 0000:00:19.0: reg 10: [mem 0xf7d00000-0xf7d1ffff]
[ 0.355653] pci 0000:00:19.0: reg 14: [mem 0xf7d35000-0xf7d35fff]
[ 0.355661] pci 0000:00:19.0: reg 18: [io 0xf080-0xf09f]
[ 0.355718] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.355740] pci 0000:00:1a.0: [8086:1e2d] type 00 class 0x0c0320
[ 0.355758] pci 0000:00:1a.0: reg 10: [mem 0xf7d34000-0xf7d343ff]
[ 0.355840] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.355866] pci 0000:00:1c.0: [8086:1e10] type 01 class 0x060400
[ 0.355996] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.356033] pci 0000:00:1c.7: [8086:1e1e] type 01 class 0x060400
[ 0.356105] pci 0000:00:1c.7: PME# supported from D0 D3hot D3cold
[ 0.356130] pci 0000:00:1d.0: [8086:1e26] type 00 class 0x0c0320
[ 0.356149] pci 0000:00:1d.0: reg 10: [mem 0xf7d33000-0xf7d333ff]
[ 0.356233] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.356255] pci 0000:00:1f.0: [8086:1e4a] type 00 class 0x060100
[ 0.356369] pci 0000:00:1f.2: [8086:1e02] type 00 class 0x010601
[ 0.356387] pci 0000:00:1f.2: reg 10: [io 0xf0d0-0xf0d7]
[ 0.356394] pci 0000:00:1f.2: reg 14: [io 0xf0c0-0xf0c3]
[ 0.356400] pci 0000:00:1f.2: reg 18: [io 0xf0b0-0xf0b7]
[ 0.356407] pci 0000:00:1f.2: reg 1c: [io 0xf0a0-0xf0a3]
[ 0.356414] pci 0000:00:1f.2: reg 20: [io 0xf060-0xf07f]
[ 0.356421] pci 0000:00:1f.2: reg 24: [mem 0xf7d32000-0xf7d327ff]
[ 0.356461] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.356477] pci 0000:00:1f.3: [8086:1e22] type 00 class 0x0c0500
[ 0.356491] pci 0000:00:1f.3: reg 10: [mem 0xf7d31000-0xf7d310ff 64bit]
[ 0.356510] pci 0000:00:1f.3: reg 20: [io 0xf040-0xf05f]
[ 0.356602] pci_bus 0000:01: busn_res: [bus 01] is inserted under [bus 00-3e]
[ 0.356605] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.356657] pci_bus 0000:02: busn_res: [bus 02] is inserted under [bus 00-3e]
[ 0.356660] pci 0000:00:1c.7: PCI bridge to [bus 02]
[ 0.356663] pci 0000:00:1c.7: bridge window [io 0xe000-0xefff]
[ 0.356666] pci 0000:00:1c.7: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 0.356683] pci_bus 0000:00: on NUMA node 0
[ 0.356684] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.356772] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.356800] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP08._PRT]
[ 0.356895] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.357033] pci0000:00: ACPI _OSC control (0x18) granted
[ 0.359632] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.359671] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15)
*0, disabled.
[ 0.359706] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 10 11 12 14 15)
[ 0.359742] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.359776] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 10 11 12 14 15)
[ 0.359813] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15)
*0, disabled.
[ 0.359850] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15)
*0, disabled.
[ 0.359884] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 10 11 12 14 15)
[ 0.359926] vgaarb: device added:
PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.359929] vgaarb: loaded
[ 0.359930] vgaarb: bridge control possible 0000:00:02.0
[ 0.359988] SCSI subsystem initialized
[ 0.359990] ACPI: bus type scsi registered
[ 0.360007] libata version 3.00 loaded.
[ 0.360016] ACPI: bus type usb registered
[ 0.360025] usbcore: registered new interface driver usbfs
[ 0.360030] usbcore: registered new interface driver hub
[ 0.360040] usbcore: registered new device driver usb
[ 0.360067] PCI: Using ACPI for IRQ routing
[ 0.361479] PCI: pci_cache_line_size set to 64 bytes
[ 0.361518] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.361519] e820: reserve RAM buffer [mem 0x40004000-0x43ffffff]
[ 0.361520] e820: reserve RAM buffer [mem 0xd9e60000-0xdbffffff]
[ 0.361521] e820: reserve RAM buffer [mem 0xda37c000-0xdbffffff]
[ 0.361523] e820: reserve RAM buffer [mem 0xda6a4000-0xdbffffff]
[ 0.361524] e820: reserve RAM buffer [mem 0xdb000000-0xdbffffff]
[ 0.361571] NetLabel: Initializing
[ 0.361572] NetLabel: domain hash size = 128
[ 0.361573] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.361579] NetLabel: unlabeled traffic allowed by default
[ 0.361612] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.361616] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.363623] Switching to clocksource hpet
[ 0.363664] AppArmor: AppArmor Filesystem Enabled
[ 0.363671] pnp: PnP ACPI init
[ 0.363676] ACPI: bus type pnp registered
[ 0.363859] pnp 00:00: [bus 00-3e]
[ 0.363861] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.363862] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.363863] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.363864] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.363865] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.363866] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.363867] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.363868] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.363869] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.363870] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.363872] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.363873] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.363874] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.363875] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.363876] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.363877] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.363878] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.363879] pnp 00:00: [mem 0xdfa00000-0xfeafffff window]
[ 0.363880] pnp 00:00: [mem 0x00010000-0x0001ffff window]
[ 0.363912] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03
(active)
[ 0.363927] pnp 00:01: [mem 0xfed40000-0xfed44fff]
[ 0.363944] system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.363945] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.363952] pnp 00:02: [io 0x0000-0x001f]
[ 0.363953] pnp 00:02: [io 0x0081-0x0091]
[ 0.363954] pnp 00:02: [io 0x0093-0x009f]
[ 0.363955] pnp 00:02: [io 0x00c0-0x00df]
[ 0.363957] pnp 00:02: [dma 4]
[ 0.363967] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.363972] pnp 00:03: [mem 0xff000000-0xffffffff]
[ 0.363983] pnp 00:03: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.364035] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[ 0.364047] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.364054] pnp 00:05: [io 0x002e-0x002f]
[ 0.364055] pnp 00:05: [io 0x004e-0x004f]
[ 0.364056] pnp 00:05: [io 0x0061]
[ 0.364057] pnp 00:05: [io 0x0063]
[ 0.364058] pnp 00:05: [io 0x0065]
[ 0.364059] pnp 00:05: [io 0x0067]
[ 0.364060] pnp 00:05: [io 0x0070]
[ 0.364061] pnp 00:05: [io 0x0080]
[ 0.364062] pnp 00:05: [io 0x0092]
[ 0.364063] pnp 00:05: [io 0x00b2-0x00b3]
[ 0.364064] pnp 00:05: [io 0x0680-0x069f]
[ 0.364065] pnp 00:05: [io 0x1000-0x100f]
[ 0.364066] pnp 00:05: [io 0xffff]
[ 0.364067] pnp 00:05: [io 0xffff]
[ 0.364068] pnp 00:05: [io 0x0400-0x0453]
[ 0.364069] pnp 00:05: [io 0x0458-0x047f]
[ 0.364070] pnp 00:05: [io 0x0500-0x057f]
[ 0.364071] pnp 00:05: [io 0x164e-0x164f]
[ 0.364089] system 00:05: [io 0x0680-0x069f] has been reserved
[ 0.364091] system 00:05: [io 0x1000-0x100f] has been reserved
[ 0.364092] system 00:05: [io 0xffff] has been reserved
[ 0.364093] system 00:05: [io 0xffff] has been reserved
[ 0.364094] system 00:05: [io 0x0400-0x0453] has been reserved
[ 0.364096] system 00:05: [io 0x0458-0x047f] has been reserved
[ 0.364097] system 00:05: [io 0x0500-0x057f] has been reserved
[ 0.364098] system 00:05: [io 0x164e-0x164f] has been reserved
[ 0.364099] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.364104] pnp 00:06: [io 0x0070-0x0077]
[ 0.364112] pnp 00:06: [irq 8]
[ 0.364123] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.364139] pnp 00:07: [io 0x0454-0x0457]
[ 0.364155] system 00:07: [io 0x0454-0x0457] has been reserved
[ 0.364157] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02
(active)
[ 0.364211] pnp 00:08: [io 0x0000-0xffffffff disabled]
[ 0.364212] pnp 00:08: [io 0x0a30-0x0a3f]
[ 0.364213] pnp 00:08: [io 0x0000-0xffffffff disabled]
[ 0.364214] pnp 00:08: [io 0x0250-0x025f]
[ 0.364231] system 00:08: [io 0x0a30-0x0a3f] has been reserved
[ 0.364232] system 00:08: [io 0x0250-0x025f] has been reserved
[ 0.364234] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.364269] pnp 00:09: [io 0x0010-0x001f]
[ 0.364270] pnp 00:09: [io 0x0022-0x003f]
[ 0.364271] pnp 00:09: [io 0x0044-0x005f]
[ 0.364272] pnp 00:09: [io 0x0062-0x0063]
[ 0.364273] pnp 00:09: [io 0x0065-0x006f]
[ 0.364274] pnp 00:09: [io 0x0072-0x007f]
[ 0.364275] pnp 00:09: [io 0x0080]
[ 0.364276] pnp 00:09: [io 0x0084-0x0086]
[ 0.364277] pnp 00:09: [io 0x0088]
[ 0.364278] pnp 00:09: [io 0x008c-0x008e]
[ 0.364279] pnp 00:09: [io 0x0090-0x009f]
[ 0.364280] pnp 00:09: [io 0x00a2-0x00bf]
[ 0.364281] pnp 00:09: [io 0x00e0-0x00ef]
[ 0.364282] pnp 00:09: [io 0x04d0-0x04d1]
[ 0.364300] system 00:09: [io 0x04d0-0x04d1] has been reserved
[ 0.364301] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.364306] pnp 00:0a: [io 0x00f0-0x00ff]
[ 0.364312] pnp 00:0a: [irq 13]
[ 0.364325] pnp 00:0a: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.364501] pnp 00:0b: [mem 0xfed1c000-0xfed1ffff]
[ 0.364503] pnp 00:0b: [mem 0xfed10000-0xfed17fff]
[ 0.364504] pnp 00:0b: [mem 0xfed18000-0xfed18fff]
[ 0.364505] pnp 00:0b: [mem 0xfed19000-0xfed19fff]
[ 0.364506] pnp 00:0b: [mem 0xf8000000-0xfbffffff]
[ 0.364507] pnp 00:0b: [mem 0xfed20000-0xfed3ffff]
[ 0.364508] pnp 00:0b: [mem 0xfed90000-0xfed93fff]
[ 0.364509] pnp 00:0b: [mem 0xfed45000-0xfed8ffff]
[ 0.364510] pnp 00:0b: [mem 0xff000000-0xffffffff]
[ 0.364511] pnp 00:0b: [mem 0xfee00000-0xfeefffff]
[ 0.364512] pnp 00:0b: [mem 0xdfa00000-0xdfa00fff]
[ 0.364543] system 00:0b: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.364544] system 00:0b: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.364545] system 00:0b: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.364548] system 00:0b: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.364549] system 00:0b: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.364550] system 00:0b: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.364551] system 00:0b: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.364553] system 00:0b: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.364554] system 00:0b: [mem 0xff000000-0xffffffff] has been reserved
[ 0.364555] system 00:0b: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.364557] system 00:0b: [mem 0xdfa00000-0xdfa00fff] has been reserved
[ 0.364558] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.364667] pnp 00:0c: [mem 0x20000000-0x201fffff]
[ 0.364668] pnp 00:0c: [mem 0x40004000-0x40004fff]
[ 0.364698] system 00:0c: [mem 0x20000000-0x201fffff] has been reserved
[ 0.364700] system 00:0c: [mem 0x40004000-0x40004fff] has been reserved
[ 0.364701] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.364716] pnp: PnP ACPI: found 13 devices
[ 0.364717] ACPI: ACPI bus type pnp unregistered
[ 0.400017] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.400034] pci 0000:00:1c.7: PCI bridge to [bus 02]
[ 0.400037] pci 0000:00:1c.7: bridge window [io 0xe000-0xefff]
[ 0.400042] pci 0000:00:1c.7: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 0.400065] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.400066] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.400067] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.400069] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
[ 0.400070] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
[ 0.400071] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
[ 0.400072] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
[ 0.400073] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff]
[ 0.400074] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff]
[ 0.400075] pci_bus 0000:00: resource 13 [mem 0xdfa00000-0xfeafffff]
[ 0.400077] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.400078] pci_bus 0000:02: resource 1 [mem 0xf7c00000-0xf7cfffff]
[ 0.400093] NET: Registered protocol family 2
[ 0.400162] TCP established hash table entries: 131072 (order: 8, 1048576
bytes)
[ 0.400296] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.400349] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.400354] TCP: reno registered
[ 0.400356] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.400358] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.400387] NET: Registered protocol family 1
[ 0.400392] pci 0000:00:02.0: Boot video device
[ 0.433487] PCI: CLS 64 bytes, default 64
[ 0.433529] Unpacking initramfs...
[ 0.733900] Freeing initrd memory: 25880k freed
[ 0.736353] audit: initializing netlink socket (disabled)
[ 0.736362] type=2000 audit(1350625067.636:1): initialized
[ 0.747078] bounce pool size: 64 pages
[ 0.747081] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.747896] VFS: Disk quotas dquot_6.5.2
[ 0.747921] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.748057] msgmni has been set to 1698
[ 0.748184] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
253)
[ 0.748200] io scheduler noop registered
[ 0.748201] io scheduler deadline registered
[ 0.748205] io scheduler cfq registered (default)
[ 0.748387] vesafb: mode is 1024x768x16, linelength=2048, pages=41
[ 0.748388] vesafb: scrolling: redraw
[ 0.748389] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.748520] vesafb: framebuffer at 0xe0000000, mapped to 0xf8080000, using
3072k, total 65472k
[ 0.769505] Console: switching to colour frame buffer device 128x48
[ 0.790444] fb0: VESA VGA frame buffer device
[ 0.790456] intel_idle: MWAIT substates: 0x1120
[ 0.790457] intel_idle: v0.4 model 0x3A
[ 0.790458] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.793195] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.793563] Non-volatile memory driver v1.3
[ 0.793564] Linux agpgart interface v0.103
[ 0.793634] ahci 0000:00:1f.2: version 3.0
[ 0.793677] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X
[ 0.793699] ahci: SSS flag set, parallel bus scan disabled
[ 0.805757] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x23
impl SATA mode
[ 0.805761] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum
part ems sxs apst
[ 0.805770] ahci 0000:00:1f.2: setting latency timer to 64
[ 0.819274] scsi0 : ahci
[ 0.819312] scsi1 : ahci
[ 0.819341] scsi2 : ahci
[ 0.819369] scsi3 : ahci
[ 0.819397] scsi4 : ahci
[ 0.819425] scsi5 : ahci
[ 0.819447] ata1: SATA max UDMA/133 abar m2048@0xf7d32000 port 0xf7d32100
irq 40
[ 0.819449] ata2: SATA max UDMA/133 abar m2048@0xf7d32000 port 0xf7d32180
irq 40
[ 0.819450] ata3: DUMMY
[ 0.819451] ata4: DUMMY
[ 0.819451] ata5: DUMMY
[ 0.819454] ata6: SATA max UDMA/133 abar m2048@0xf7d32000 port 0xf7d32380
irq 40
[ 0.819490] libphy: Fixed MDIO Bus: probed
[ 0.819491] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.819509] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 0.819512] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 0.819515] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus
number 1
[ 0.823415] ehci_hcd 0000:00:1a.0: debug port 2
[ 0.823421] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 0.823432] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf7d34000
[ 0.832327] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 0.832346] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.832349] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 0.832351] usb usb1: Product: EHCI Host Controller
[ 0.832354] usb usb1: Manufacturer: Linux 3.6.2 ehci_hcd
[ 0.832356] usb usb1: SerialNumber: 0000:00:1a.0
[ 0.832431] hub 1-0:1.0: USB hub found
[ 0.832433] hub 1-0:1.0: 2 ports detected
[ 0.832479] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.832481] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 0.832484] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
number 2
[ 0.836378] ehci_hcd 0000:00:1d.0: debug port 2
[ 0.836384] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 0.836393] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf7d33000
[ 0.845623] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.845639] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.845641] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 0.845643] usb usb2: Product: EHCI Host Controller
[ 0.845645] usb usb2: Manufacturer: Linux 3.6.2 ehci_hcd
[ 0.845647] usb usb2: SerialNumber: 0000:00:1d.0
[ 0.845718] hub 2-0:1.0: USB hub found
[ 0.845719] hub 2-0:1.0: 2 ports detected
[ 0.845752] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.845760] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.845767] Initializing USB Mass Storage driver...
[ 0.845776] usbcore: registered new interface driver usb-storage
[ 0.845776] USB Mass Storage support registered.
[ 0.845779] usbcore: registered new interface driver ums-alauda
[ 0.845782] usbcore: registered new interface driver ums-cypress
[ 0.845785] usbcore: registered new interface driver ums-datafab
[ 0.845788] usbcore: registered new interface driver ums-freecom
[ 0.845791] usbcore: registered new interface driver ums-isd200
[ 0.845794] usbcore: registered new interface driver ums-jumpshot
[ 0.845798] usbcore: registered new interface driver ums-karma
[ 0.845801] usbcore: registered new interface driver ums-onetouch
[ 0.845803] usbcore: registered new interface driver ums-sddr09
[ 0.845806] usbcore: registered new interface driver ums-sddr55
[ 0.845809] usbcore: registered new interface driver ums-usbat
[ 0.845832] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 0.848314] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.848320] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.848363] mousedev: PS/2 mouse device common for all mice
[ 0.848410] rtc_cmos 00:06: RTC can wake from S4
[ 0.848504] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 0.848532] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.848568] cpuidle: using governor ladder
[ 0.848648] usbcore: registered new interface driver usbhid
[ 0.848649] usbhid: USB HID core driver
[ 0.848725] ashmem: initialized
[ 0.848799] TCP: cubic registered
[ 0.848847] NET: Registered protocol family 10
[ 0.848955] lib80211: common routines for IEEE802.11 drivers
[ 0.848956] lib80211_crypt: registered algorithm 'NULL'
[ 0.848961] Key type dns_resolver registered
[ 0.848963] Key type ceph registered
[ 0.848966] libceph: loaded (mon/osd proto 15/24, osdmap 5/6 5/6)
[ 0.849080] Using IPI No-Shortcut mode
[ 0.849185] PM: Checking hibernation image partition
/dev/disk/by-id/ata-INTEL_SSDSC2CW060A3_CVCV205106EB060AGN-part3
[ 1.138146] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[ 1.138155] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.147391] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 1.147396] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK)
filtered out
[ 1.147399] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION
OVERLAY) filtered out
[ 1.150155] ata1.00: ATAPI: HL-DT-ST BDDVDRW UH12LS29, 1.00, max UDMA/133
[ 1.155196] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 1.155201] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK)
filtered out
[ 1.155205] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION
OVERLAY) filtered out
[ 1.157949] ata1.00: configured for UDMA/133
[ 1.176774] scsi 0:0:0:0: CD-ROM HL-DT-ST BDDVDRW UH12LS29 1.00
PQ: 0 ANSI: 5
[ 1.261471] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.261475] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.261747] hub 1-1:1.0: USB hub found
[ 1.261843] hub 1-1:1.0: 6 ports detected
[ 1.367470] usb 2-1: new high-speed USB device number 2 using ehci_hcd
[ 1.490837] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.490842] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.491094] hub 2-1:1.0: USB hub found
[ 1.491184] hub 2-1:1.0: 8 ports detected
[ 1.493787] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.495201] ata2.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 1.495205] ata2.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK)
filtered out
[ 1.495208] ata2.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION
OVERLAY) filtered out
[ 1.505564] ata2.00: ATA-9: INTEL SSDSC2CW060A3, 400i, max UDMA/133
[ 1.505569] ata2.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.515105] ata2.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 1.515110] ata2.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK)
filtered out
[ 1.515113] ata2.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION
OVERLAY) filtered out
[ 1.525523] ata2.00: configured for UDMA/133
[ 1.525627] scsi 1:0:0:0: Direct-Access ATA INTEL SSDSC2CW06 400i
PQ: 0 ANSI: 5
[ 1.176993] ACPI: Invalid Power Resource to register!
[ 1.525797] sd 1:0:0:0: [sda] 117231408 512-byte logical blocks: (60.0
GB/55.8 GiB)
[ 1.525912] sd 1:0:0:0: [sda] Write Protect is off
[ 1.525915] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.525989] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.526667] sda: sda1 sda2 sda3 sda4
[ 1.527024] sd 1:0:0:0: [sda] Attached SCSI disk
[ 1.557024] usb 1-1.1: new full-speed USB device number 3 using ehci_hcd
[ 1.643271] usb 1-1.1: New USB device found, idVendor=19ff, idProduct=0231
[ 1.643276] usb 1-1.1: New USB device strings: Mfr=0, Product=2,
SerialNumber=0
[ 1.643278] usb 1-1.1: Product: Dynex wireless combo
[ 1.736431] tsc: Refined TSC clocksource calibration: 3392.304 MHz
[ 1.736437] Switching to clocksource tsc
[ 1.756460] usb 2-1.7: new high-speed USB device number 3 using ehci_hcd
[ 1.841599] usb 2-1.7: New USB device found, idVendor=0b05, idProduct=17ab
[ 1.841603] usb 2-1.7: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 1.841606] usb 2-1.7: Product: 802.11n WLAN Adapter
[ 1.841608] usb 2-1.7: Manufacturer: Realtek
[ 1.841610] usb 2-1.7: SerialNumber: 00e04c000001
[ 1.842788] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.842851] PM: Hibernation image not present or could not be loaded.
[ 1.842859] registered taskstats version 1
[ 1.843204] Magic number: 0:561:618
[ 1.843284] rtc_cmos 00:06: setting system clock to 2012-10-19 05:37:49 UTC
(1350625069)
[ 1.843418] Freeing unused kernel memory: 452k freed
[ 1.865280] emc: device handler registered
[ 1.866193] rdac: device handler registered
[ 1.867223] alua: device handler registered
[ 1.868111] hp_sw: device handler registered
[ 1.870776] udevd[109]: starting version 182
[ 1.876319] ACPI: Fan [FAN0] (off)
[ 1.876344] ACPI: Fan [FAN1] (off)
[ 1.876362] ACPI: Fan [FAN2] (off)
[ 1.876380] ACPI: Fan [FAN3] (off)
[ 1.876396] ACPI: Fan [FAN4] (off)
[ 1.876481] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 1.877373] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 1.877376] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.877380] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus
number 3
[ 1.877463] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 1.877469] xhci_hcd 0000:00:14.0: irq 16, io mem 0xf7d20000
[ 1.877509] xhci_hcd 0000:00:14.0: irq 41 for MSI/MSI-X
[ 1.877553] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.877555] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.877556] usb usb3: Product: xHCI Host Controller
[ 1.877557] usb usb3: Manufacturer: Linux 3.6.2 xhci_hcd
[ 1.877558] usb usb3: SerialNumber: 0000:00:14.0
[ 1.877617] ACPI: Power Button [PWRB]
[ 1.877635] xHCI xhci_add_endpoint called for root hub
[ 1.877636] xHCI xhci_check_bandwidth called for root hub
[ 1.877655] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 1.877655] hub 3-0:1.0: USB hub found
[ 1.877669] hub 3-0:1.0: 4 ports detected
[ 1.877676] ACPI: Power Button [PWRF]
[ 1.877715] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.877717] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus
number 4
[ 1.877735] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.877736] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.877737] usb usb4: Product: xHCI Host Controller
[ 1.877738] usb usb4: Manufacturer: Linux 3.6.2 xhci_hcd
[ 1.877739] usb usb4: SerialNumber: 0000:00:14.0
[ 1.877782] xHCI xhci_add_endpoint called for root hub
[ 1.877783] xHCI xhci_check_bandwidth called for root hub
[ 1.877798] hub 4-0:1.0: USB hub found
[ 1.877807] hub 4-0:1.0: 4 ports detected
[ 1.886043] input: Dynex wireless combo as
/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/input/input2
[ 1.886100] hid-generic 0003:19FF:0231.0001: input,hidraw0: USB HID v1.11
Keyboard [Dynex wireless combo] on usb-0000:00:1a.0-1.1/input0
[ 1.886212] input: Dynex wireless combo as
/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.1/input/input3
[ 1.886281] hid-generic 0003:19FF:0231.0002: input,hidraw1: USB HID v1.11
Mouse [Dynex wireless combo] on usb-0000:00:1a.0-1.1/input1
[ 1.895242] [drm] Initialized drm 1.1.0 20060810
[ 1.899503] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.899506] ACPI: Thermal Zone [TZ00] (28 C)
[ 1.899630] thermal LNXTHERM:01: registered as thermal_zone1
[ 1.899631] ACPI: Thermal Zone [TZ01] (30 C)
[ 1.900217] pci 0000:00:00.0: Intel Ivybridge Chipset
[ 1.900245] pci 0000:00:00.0: detected gtt size: 2097152K total, 262144K
mappable
[ 1.900802] pci 0000:00:00.0: detected 65536K stolen memory
[ 1.900890] checking generic (e0000000 3ff0000) vs hw (e0000000 10000000)
[ 1.900891] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing
generic driver
[ 1.525836] ACPI: Invalid Power Resource to register!
[ 1.900902] Console: switching to colour dummy device 80x25
[ 1.900963] i915 0000:00:02.0: setting latency timer to 64
[ 1.901579] i915 0000:00:02.0: irq 42 for MSI/MSI-X
[ 1.901584] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 1.901584] [drm] Driver supports precise vblank timestamp query.
[ 1.901641] vgaarb: device changed decodes:
PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 1.981233] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 2.317211] fbcon: inteldrmfb (fb0) is primary device
[ 2.477547] Console: switching to colour frame buffer device 128x48
[ 2.479153] fb0: inteldrmfb frame buffer device
[ 2.479154] drm: registered panic notifier
[ 2.491222] acpi device:4b: registered as cooling_device9
[ 2.491319] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 2.491349] input: Video Bus as
/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 2.491427] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 3.348442] PM: Marking nosave pages: [mem 0x0009d000-0x000fffff]
[ 3.348445] PM: Marking nosave pages: [mem 0x20000000-0x201fffff]
[ 3.348454] PM: Basic memory bitmaps created
[ 3.357595] PM: Basic memory bitmaps freed
[ 3.357598] video LNXVIDEO:00: Restoring backlight state
[ 3.363579] PM: Starting manual resume from disk
[ 3.363582] PM: Hibernation image partition 8:3 present
[ 3.363582] PM: Looking for hibernation image.
[ 3.363684] PM: Image not found (code -22)
[ 3.363686] PM: Hibernation image not present or could not be loaded.
[ 3.381634] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts:
acl,user_xattr
[ 3.395784] EXT4-fs (sda4): re-mounted. Opts: acl,user_xattr
[ 3.686503] systemd-readahead-replay[290]: Bumped block_nr parameter of 8:0
to 16384. This is a temporary hack and should be removed one day.
[ 4.102227] udevd[322]: starting version 182
[ 4.181001] microcode: CPU0 sig=0x306a9, pf=0x2, revision=0x12
[ 4.181819] microcode: CPU1 sig=0x306a9, pf=0x2, revision=0x12
[ 4.182137] microcode: CPU2 sig=0x306a9, pf=0x2, revision=0x12
[ 4.182396] microcode: CPU3 sig=0x306a9, pf=0x2, revision=0x12
[ 4.182656] microcode: Microcode Update Driver: v2.00
<tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
[ 4.265479] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
[ 4.302072] EXT4-fs (sda4): re-mounted. Opts: acl,user_xattr
[ 4.573758] e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k
[ 4.573760] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
[ 4.573786] e1000e 0000:00:19.0: setting latency timer to 64
[ 4.574085] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to
dynamic conservative mode
[ 4.574113] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 4.579297] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 4.580807] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 4.580827] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 4.588989] cfg80211: Calling CRDA to update world regulatory domain
[ 4.593249] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda
tray
[ 4.593251] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 4.593551] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 4.602026] kvm: disabled by bios
[ 4.607341] cfg80211: World regulatory domain updated:
[ 4.607344] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 4.607345] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 4.607346] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 4.607347] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 4.607348] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 4.607349] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 4.622090] kvm: disabled by bios
[ 4.645144] rtl8192cu: Chip version 0x11
[ 4.731330] Adding 4193276k swap on /dev/sda3. Priority:-1 extents:1
across:4193276k SS
[ 4.732519] rtl8192cu: MAC address: 10:bf:48:fb:c9:d1
[ 4.732525] rtl8192cu: Board Type 0
[ 4.732766] rtlwifi: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 4.732800] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw.bin
[ 4.732847] usbcore: registered new interface driver rtl8192cu
[ 4.734823] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 4.735132] rtlwifi: wireless switch is on
[ 4.835794] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1)
e8:40:f2:05:f1:85
[ 4.835796] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 4.835846] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: FFFFFF-0FF
[ 4.835910] ACPI Warning: 0x0000f040-0x0000f05f SystemIO conflicts with
Region \_SB_.PCI0.SBUS.SMBI 1 (20120711/utaddress-251)
[ 4.835914] ACPI: If an ACPI driver is available for this device, you should
use it instead of the native driver
[ 4.835989] ACPI Warning: 0x00000428-0x0000042f SystemIO conflicts with
Region \PMIO 1 (20120711/utaddress-251)
[ 4.835993] ACPI: If an ACPI driver is available for this device, you should
use it instead of the native driver
[ 4.835997] ACPI Warning: 0x00000500-0x0000053f SystemIO conflicts with
Region \GPIO 1 (20120711/utaddress-251)
[ 4.835999] ACPI: If an ACPI driver is available for this device, you should
use it instead of the native driver
[ 4.836000] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 4.845936] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts:
acl,user_xattr
[ 5.810691] rtl8192cu: MAC auto ON okay!
[ 5.843330] rtl8192cu: Tx queue select: 0x05
[ 6.214843] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6.474945] RPC: Registered named UNIX socket transport module.
[ 6.474947] RPC: Registered udp transport module.
[ 6.474948] RPC: Registered tcp transport module.
[ 6.474948] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 6.477114] FS-Cache: Loaded
[ 6.479765] FS-Cache: Netfs 'nfs' registered for caching
[ 6.984772] wlan0: authenticate with 00:18:f8:ff:72:d5
[ 7.009152] wlan0: send auth to 00:18:f8:ff:72:d5 (try 1/3)
[ 7.210781] wlan0: send auth to 00:18:f8:ff:72:d5 (try 2/3)
[ 7.413520] wlan0: send auth to 00:18:f8:ff:72:d5 (try 3/3)
[ 7.616274] wlan0: authentication with 00:18:f8:ff:72:d5 timed out
[ 8.369759] EXT4-fs (sda4): re-mounted. Opts: acl,user_xattr,commit=0
[ 8.372320] EXT4-fs (sda2): re-mounted. Opts: acl,user_xattr,commit=0
[ 10.166799] fuse init (API version 7.20)
< Previous Next >