Mailinglist Archive: opensuse (4547 mails)

< Previous Next >
Re: [SLE] CUPS problem -- starting with lpinfo...
  • From: "James D. Ivey" <jim@xxxxxxxxxxx>
  • Date: Thu, 06 May 2004 15:45:34 -0700
  • Message-id: <1083883533.2237.102.camel@xxxxxxxxxxxxxxxxxxx>
On Thu, 2004-05-06 at 15:06, Patrick Shanahan wrote:
> <snip>
> > But, more to the point, the steps outlined in the quoted message didn't
> > help. I have AuthType in cupsd.conf set to "Basic", not "Digest", so
> > the lppasswd command seems irrelevant. I also have the AuthGroupName
> > set to sys and root is a member of group sys.
> >
> > More basically, what would cause the error message on lpinfo? Beyond
> > authentication, it seems there's something more fundamentally wrong with
> > my setup. Knowing what can cause that type of error would help me dig
> > in the right area.
> >
> > To remind people, here's the error again:
> >
> > linux1:/etc/cups # lpinfo -v
> > lpinfo: cups-get-devices failed: server-error-operation-not-supported
> >
> > Any help is greatly appreciated.
> >
> > Regards,
> >
> > Jim
> >
> >
> > On Thu, 2004-05-06 at 14:31, Patrick Shanahan wrote:
> > > * James D. Ivey <jim@xxxxxxxxxxx> [05-06-04 15:17]:
> > > >
> > > > I haven't been able to get into the web interface for cups yet. It
> > > > doesn't access my root id and password. But I'm trying to take it
> > > > step-by-step, starting with lpinfo.
> > >
> > >
> > > Reading this list help a lot. Posted earlier today:
> > >
> > > <quote>
> > > Date: Thu, 06 May 2004 10:06:51 -0400
> > > From: Louis Richards <louis@xxxxxxxxxxxxxxxxxx>
> > > To: suse-linux-e@xxxxxxxx
> > > Subject: Re: [SLE] HP3030: Printer/Scanner clash
> > > Mailing-List: contact suse-linux-e-help@xxxxxxxx; run by ezmlm
> > > Message-ID: <409A467B.5080008@xxxxxxxxxxxxxxxxxx>
> > >
> > > <trim...>
> > > Last but not least, you need to set up your printer. Do not use Yast for
> > > this. Use the CUPS web interface at http://localhost:631/ . If you have
> > > never used this interface before, you will have to add an admin user
> > > first by entering "lppasswd -g sys -a user". I am not sure if you have
> > > to restart cups or not after this, but it couldn't hurt. Type "rccups
> > > restart". Use the web interface to set up as many printers as needed for
> > > different resolutions setting the device to the PTAL device created
> > > above.
> > > </quote>
> > >
> > >
> > > You *do* read the list ??
> > >
>
> Well, if cups says it cannot do the operation (as quoted), I would
> restart cups (/usr/sbin/rccups restart) and try again. If it still
> does not work, I would consider reinstalling cups.
>
> If that does not work, perhaps you need to reconsider the 'Basic'
> authorization.

I was avoiding "Digest" in hopes of keeping things simple, but -- alas
-- that did the trick! Thanks!

Jim
--
James D. Ivey <jim@xxxxxxxxxxx>
Law Offices of James D. Ivey

This e-mail address is heavily spammed and heavily filtered. It's
better to reach me through my web site: http://www.iveylaw.com



< Previous Next >
Follow Ups