Mailinglist Archive: radeonhd (319 mails)
| < Previous | Next > |
[radeonhd] [Bug 16929] Sapphire Radeon HD 3450 doesn't work (black screen)
- From: bugzilla-daemon@xxxxxxxxxxxxxxx
- Date: Sat, 1 Nov 2008 11:54:14 -0700 (PDT)
- Message-id: <20081101185420.113001300E2@xxxxxxxxxxxxxxxxxxxxxxxx>
http://bugs.freedesktop.org/show_bug.cgi?id=16929
Egbert Eich <eich@xxxxxxxxxxxxxxxxxxx> changed:
What |Removed |Added
----------------------------------------------------------------------------
Status|NEW |RESOLVED
Resolution| |DUPLICATE
--- Comment #14 from Egbert Eich <eich@xxxxxxxxxxxxxxxxxxx> 2008-09-01
02:34:37 PST ---
(In reply to comment #13)
Does the picture 'scroll' when you move the mouse to the edges?
OK, what resolution do you get on the TV?
Can you send a verbose log file for this case?
- ie where you first use the 15", then pull it off, then do xrandr again?
There is no load detection on your HDMI connector.
Everything there looks well - except that you get a black screen.
--- Comment #15 from Egbert Eich <eich@xxxxxxxxxxxxxxxxxxx> 2008-11-01
11:54:13 PST ---
*** This bug has been marked as a duplicate of bug 16892 ***
--
Configure bugmail: http://bugs.freedesktop.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the QA contact for the bug.
_______________________________________________
xorg-team mailing list
xorg-team@xxxxxxxxxxx
http://lists.x.org/mailman/listinfo/xorg-team
--
To unsubscribe, e-mail: radeonhd+unsubscribe@xxxxxxxxxxxx
For additional commands, e-mail: radeonhd+help@xxxxxxxxxxxx
Egbert Eich <eich@xxxxxxxxxxxxxxxxxxx> changed:
What |Removed |Added
----------------------------------------------------------------------------
Status|NEW |RESOLVED
Resolution| |DUPLICATE
--- Comment #14 from Egbert Eich <eich@xxxxxxxxxxxxxxxxxxx> 2008-09-01
02:34:37 PST ---
(In reply to comment #13)
Did a git pull this morning. Tried different setups to get a picture using
RandR, no luck.
I used the modes line with NoRandR and that works. I also tried it earlier
with
a virtual line. The effect is the same. I get picture at 1920x1080, but the
image seems slightly too big for the tv. The left, right and bottom edges fall
off screen.
Does the picture 'scroll' when you move the mouse to the edges?
I did notice however that if I connect an 15" (1024x768) lcd to the DVI
interface, the picture is cloned to the tv in RandR mode. But whatever I try
with xrandr, I can't get the right resolution on the tv. If I disconnect the
OK, what resolution do you get on the TV?
15" and use xrandr again, the picture on the tv goes black.
Can you send a verbose log file for this case?
- ie where you first use the 15", then pull it off, then do xrandr again?
So it seems there's some load detection problem on the HDMI connector.
There is no load detection on your HDMI connector.
Everything there looks well - except that you get a black screen.
--- Comment #15 from Egbert Eich <eich@xxxxxxxxxxxxxxxxxxx> 2008-11-01
11:54:13 PST ---
*** This bug has been marked as a duplicate of bug 16892 ***
--
Configure bugmail: http://bugs.freedesktop.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the QA contact for the bug.
_______________________________________________
xorg-team mailing list
xorg-team@xxxxxxxxxxx
http://lists.x.org/mailman/listinfo/xorg-team
--
To unsubscribe, e-mail: radeonhd+unsubscribe@xxxxxxxxxxxx
For additional commands, e-mail: radeonhd+help@xxxxxxxxxxxx
| < Previous | Next > |