With the rules below, 168.103.176.49 is working, But the second address assigned 168.103.176.52 is not. I know I am very close and I just can not seem to see the problem. ip address show ... 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:15:17:55:80:cd brd ff:ff:ff:ff:ff:ff inet 168.103.176.49/29 brd 168.103.176.55 scope global eth1 inet 168.103.176.52/29 brd 168.103.176.55 scope global secondary eth1:mwiap So they both are shown there. ip route show 168.103.176.48/29 dev eth1 proto kernel scope link src 168.103.176.49 168.103.176.248/29 dev eth1 scope link src 168.103.176.49 198.60.105.0/24 dev eth0 proto kernel scope link src 198.60.105.164 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.165 169.254.0.0/16 dev eth0 scope link 127.0.0.0/8 dev lo scope link default via 198.60.105.2 dev eth0 ip route list table T1 255.255.255.248 dev eth1 scope link 198.60.105.0/24 dev eth0 scope link src 198.60.105.164 127.0.0.0/8 dev lo scope link default via 198.60.105.2 dev eth0 ip route list table T2 255.255.255.0 dev eth0 scope link 168.103.176.248/29 dev eth1 scope link src 168.103.176.49 127.0.0.0/8 dev lo scope link default via 168.103.176.54 dev eth1 On Fri, 31 Aug 2012, Boyd Lynn Gerber wrote:
Here is the cleaned up version
IF1=eth0 IF2=eth1 IP1=198.60.105.164 IP2=168.103.176.49 P0=192.168.0.1 P1=198.60.105.2 P2=168.103.176.54 P0_NET=192.168.0.0/24 P1_NET=198.60.105.0/24 P2_NET=168.103.176.248/29 P0_NET_MASK=255.255.255.0 P1_NET_MASK=255.255.255.0 P2_NET_MASK=255.255.255.248 ip route add $P1_NET dev $IF1 src $IP1 table T1 ip route add default via $P1 table T1 ip route add $P2_NET dev $IF2 src $IP2 table T2 ip route add default via $P2 table T2 ip route add $P1_NET dev $IF1 src $IP1 ip route add $P2_NET dev $IF2 src $IP2 ip route add default via $P1 ip rule add from $IP1 table T1 ip rule add from $IP2 table T2 ip route add $P2_NET_MASK dev $IF2 table T1 ip route add 127.0.0.0/8 dev lo table T1 ip route add $P1_NET_MASK dev $IF1 table T2 ip route add 127.0.0.0/8 dev lo table T2
Thanks for all the assistence so far. I am really close. Thanks for any more suggestiosn. -- Boyd Gerber <gerberb@zenez.com> 801 849-0213 ZENEZ 1042 East Fort Union #135, Midvale Utah 84047 -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org