Mailinglist Archive: opensuse (888 mails)
| < Previous | Next > |
Re: [opensuse] thicking hard disk problem
- From: Dave Howorth <dhoworth@xxxxxxxxxxxxxxxxx>
- Date: Mon, 17 Jan 2011 10:16:09 +0000
- Message-id: <4D3416E9.1090908@mrc-lmb.cam.ac.uk>
Peter Nikolic wrote:
Has the system ever worked perfectly or has it always shown these
symptoms in this configuration?
There's an explanation of the error messages at
https://ata.wiki.kernel.org/index.php/Libata_error_messages that might help.
But I have to say that I'm pretty much still as mystified as I was even
after reading that page. Does anybody know of a better ( == more idiot
proof) explanation?
Almost certainly.
I don't know whether it is a disk or a problem with the controller or
your system setup (e.g. power supply). I have a system where the disks
are shown as healthy by smart and pass all manufacturers' tests but show
similar symptoms when attached to that particular system.
What does smart say about your disks?
Run smart -t long <device>
And then after it has finished run smart -a <device> to see what the
result was.
These comments sound like good advice!
Cheers, Dave
--
To unsubscribe, e-mail: opensuse+unsubscribe@xxxxxxxxxxxx
For additional commands, e-mail: opensuse+help@xxxxxxxxxxxx
On Saturday 15 January 2011 00:23:47 John Andersen wrote:
On 1/14/2011 3:25 PM, Istvan Gabor wrote:
I have opensuse 11.2 with kernel 2.6.31.14-0.4-desktop.
The system has two 160 GB Maxtor hard disks which are linked to a
Silicon Image 3114 PCI SATA (soft) raid controller. They are configured
as RAID1 (mirror) devices and dmraid is set up and works well except
from the symptom below.
The problem is that occasionally one of the disks gives a ticking sound
and this sound becomes frequent when the activity of the disks increase
(eg. when copying from cd to disk).
Has the system ever worked perfectly or has it always shown these
symptoms in this configuration?
In /var/log/messages file there are several lines like these:
Jan 14 23:43:17 linux kernel: [ 4468.814798] ata5.00: exception Emask
0x10 SAct 0x0 SErr 0x10000 action 0xe frozen Jan 14 23:43:17 linux
kernel: [ 4468.814840] ata5: SError: { PHYRdyChg } Jan 14 23:43:17 linux
kernel: [ 4468.814858] ata5.00: cmd c8/00:08:67:05:f4/00:00:00:00:00/e0
tag 0 dma 4096 in Jan 14 23:43:17 linux kernel: [ 4468.814860]
res d0/d0:d0:d0:d0:d0/ff:ff:ff:ff:ff/c0 Emask 0x12 (ATA bus error) Jan
14 23:43:17 linux kernel: [ 4468.814878] ata5.00: status: { Busy } Jan
14 23:43:17 linux kernel: [ 4468.814887] ata5.00: error: { ICRC UNC IDNF
} Jan 14 23:43:17 linux kernel: [ 4468.814904] ata5: hard resetting link
There's an explanation of the error messages at
https://ata.wiki.kernel.org/index.php/Libata_error_messages that might help.
But I have to say that I'm pretty much still as mystified as I was even
after reading that page. Does anybody know of a better ( == more idiot
proof) explanation?
These messages occur several times in the file.
I guess they have to do something with the ticks.
Almost certainly.
I don't know whether it is a disk or a problem with the controller or
your system setup (e.g. power supply). I have a system where the disks
are shown as healthy by smart and pass all manufacturers' tests but show
similar symptoms when attached to that particular system.
What does smart say about your disks?
Run smart -t long <device>
And then after it has finished run smart -a <device> to see what the
result was.
I had one of these a year or two ago on software raid.
Not good. Make sure you have a hot spare in your raid definition.
That sounds very much like a dying drive to me back it up
These comments sound like good advice!
Cheers, Dave
--
To unsubscribe, e-mail: opensuse+unsubscribe@xxxxxxxxxxxx
For additional commands, e-mail: opensuse+help@xxxxxxxxxxxx
| < Previous | Next > |