Mailinglist Archive: opensuse (2479 mails)

[lists@xxxxxxxxxxxx]

Hi,
I have an Asus R2Hv umpc upon which I have installed 11.2.  All is  
fine, display & intel 915 adapter is detected correctly (11.1 didn't).  
 However, the device has a Panjit touchset device which is not  
configured correctly.  It is detected by X, but tries to load the  
synaptics driver rather than evtouch.  I have installed evtouch but  
don't know how to get it up and running.  The umpc is not a choice in  
sax for tablet (although others do use evtouch).  I have previously  
had this running fine under 11.0.

Here are the lines from xorg.0.log

(II) config/hal: Adding input device PANJIT PANJIT TouchSet Digitizer
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules//input/synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
        compiled for 1.6.5, module version = 1.1.3
        Module class: X.Org XInput Driver
        ABI class: X.Org XInput driver, version 4.0
(II) Synaptics touchpad driver version 1.1.3
(**) Option "Device" "/dev/input/event8"
(**) Option "SHMConfig" "on"
(**) Option "HorizScrollDelta" "0"
(--) PANJIT PANJIT TouchSet Digitizer: no supported touchpad found
(EE) PANJIT PANJIT TouchSet Digitizer Unable to query/initialize  
Synaptics hardware.
(EE) PreInit failed for input device "PANJIT PANJIT TouchSet Digitizer"
(II) UnloadModule: "synaptics"

and the relevant bits from dmesg

[    5.756228] usb 1-7.1: new full speed USB device using ehci_hcd and  
address 9
[    5.848964] usb 1-7.1: New USB device found, idVendor=08ff, idProduct=1600
[    5.848972] usb 1-7.1: New USB device strings: Mfr=0, Product=1,  
SerialNumber=0
[    5.848979] usb 1-7.1: Product: Fingerprint Sensor
[    5.849141] usb 1-7.1: configuration #1 chosen from 1 choice
[    5.936225] usb 1-7.2: new low speed USB device using ehci_hcd and  
address 10
[    6.049089] usb 1-7.2: New USB device found, idVendor=134c, idProduct=0005
[    6.049098] usb 1-7.2: New USB device strings: Mfr=1, Product=2,  
SerialNumber=0
[    6.049105] usb 1-7.2: Product: PANJIT TouchSet Digitizer
[    6.049110] usb 1-7.2: Manufacturer: PANJIT
[    6.049263] usb 1-7.2: configuration #1 chosen from 1 choice

[   10.358809] input: PANJIT PANJIT TouchSet Digitizer as  
/devices/pci0000:00/0000:00:1d.7/usb1/1-7/1-7.2/1-7.2:1.0/input/input8
[   10.359086] generic-usb 0003:134C:0005.0002: input,hiddev0,hidraw1:  
USB HID v1.11 Mouse [PANJIT PANJIT TouchSet Digitizer] on  
usb-0000:00:1d.7-7.2/input0

My question then, with xorg.conf no longer in use, how do I configure  
the tablet parameters, and get it to load the module and set parameters?

Thanks,
Allen


--
To unsubscribe, e-mail: opensuse+unsubscribe@xxxxxxxxxxxx
For additional commands, e-mail: opensuse+help@xxxxxxxxxxxx