Mailinglist Archive: opensuse (2255 mails)

[mukul <mukul.singh@xxxxxxxxxxxxxxxxxx>]

Rajko M. wrote:
> On Friday 13 March 2009 08:32:54 am mukul wrote:
> > Mukul Singh wrote:
> > > Rajko M. wrote:
> > > > On Thursday 12 March 2009 08:36:47 pm Mukul Singh wrote:
> > > > ...
> > > >
> > > > > That has not been my experience. I removed pulse except that library
> > > > > and the sound won't work on my laptop unless I do rcalsasound restart.
> > > > > BTW, I have tried VLC as suggested by another person and that too did
> > > > > not work.
> > > > >
> > > > > Regards
> > > > Mukul,
> > > >
> > > > 1) Check is PulseAudio enabled. Use Yast sound module:
> > > >    YaST > Sound > button Other > PulseAudio configuration
> > > > It should say that PulseAudio is not installed.
> > > I did the check and it does say that PulseAudio is not installed.
> > >
> > > > 2) Remove you sound card from YaST sound, close YaST sound, then open
> > > > again. This should find and reconfigure your card for current sound
> > > > system.
> > Hi,
> >
> > I have done this and the sound works (for mplayer, vlc etc., no sound
> > for videos on youtube through Firefox or Opera) until I reboot the
> > machine. Once I reboot, the things go back to what they were before I
> > did step 2.
> >
> > Regards
>
> So a word or two about your hardware could be next step.
>
>  lspci
>  uname -a 
>
> But it would be also good to open new thread, with question, and subject like 
> above. General discussion about operating system will not solve your audio 
> problem, and it is hard to find your answers in the pile of junk that such 
> discussions generate.  

Hi,

I followed instructions given on :

http://en.opensuse.org/SDB:AudioTroubleshooting#Symptom

and

http://en.opensuse.org/SDB:Intel-HDA_sound_problems

and the current status is that I get sound in mplayer, even after I log
back in. The current problem is that the sound is very low, even though
in KMix I have selected the appropriate channel and set the volume to 100%.

HW info is as follows:

lspci :

00:00.0 Host bridge: nVidia Corporation MCP79 Host Bridge (rev b1)
00:00.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.0 ISA bridge: nVidia Corporation MCP79 LPC Bridge (rev b2)
00:03.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.2 SMBus: nVidia Corporation MCP79 SMBus (rev b1)
00:03.3 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.4 RAM memory: nVidia Corporation Device 0a98 (rev b1)
00:03.5 Co-processor: nVidia Corporation MCP79 Co-processor (rev b1)
00:04.0 USB Controller: nVidia Corporation MCP79 OHCI USB 1.1 Controller
(rev b1)
00:04.1 USB Controller: nVidia Corporation MCP79 EHCI USB 2.0 Controller
(rev b1)
00:08.0 Audio device: nVidia Corporation MCP79 High Definition Audio
(rev b1)
00:09.0 PCI bridge: nVidia Corporation MCP79 PCI Bridge (rev b1)
00:0a.0 Ethernet controller: nVidia Corporation MCP79 Ethernet (rev b1)
00:0b.0 SATA controller: nVidia Corporation MCP79 AHCI Controller (rev b1)
00:10.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:15.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:16.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:17.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
00:18.0 PCI bridge: nVidia Corporation MCP79 PCI Express Bridge (rev b1)
02:00.0 VGA compatible controller: nVidia Corporation GeForce 9200M G
(rev b1)
06:00.0 Network controller: Atheros Communications Inc. AR928X Wireless
Network Adapter (PCI-Express) (rev 01)

uname -a :

Linux linux-95f9 2.6.27.19-3.2-default #1 SMP 2009-02-25 15:40:44 +0100
i686 i686 i386 GNU/Linux

Regards
-- 
To unsubscribe, e-mail: opensuse+unsubscribe@xxxxxxxxxxxx
For additional commands, e-mail: opensuse+help@xxxxxxxxxxxx