Mailinglist Archive: opensuse (3031 mails)

["umesh b" <umesh.kollam@xxxxxxxxx>]

On Feb 5, 2008 10:29 PM, Constant Brouerius van Nidek
<constant@xxxxxxxxxxx> wrote:
> For your info, I am using Kinternet.
> My info is as follows:
>
> # hwinfo --usb
>
>
> 06: USB 00.0: 10200 Modem
>   [Created at usb.122]
>
> UDI: 
> /org/freedesktop/Hal/devices/usb_device_1b7d_70a_noserial_if0_serial_unknown_0
>   Unique ID: lfzD.gQKXOFrp8H8
>   Parent ID: ADDn.hKbQSFhpkw6
>   SysFS ID: /devices/pci0000:00/0000:00:07.2/usb1/1-1/1-1.1/1-1.1:1.0
>   SysFS BusID: 1-1.1:1.0
>   Hardware Class: modem
>   Model: "Qualcomm CDMA Technologies MSM"
>   Hotplug: USB
>   Vendor: usb 0x1b7d "Qualcomm, Incorporated"
>   Device: usb 0x070a "Qualcomm CDMA Technologies MSM"
>   Driver: "cdc_acm"
>   Driver Modules: "cdc_acm"
>   Device File: /dev/ttyACM0
>   Speed: 12 Mbps
>   Module Alias: "usb:v1B7Dp070Ad0000dc02dsc00dp00ic02isc02ip01"
>   Driver Info #0:
>     Driver Status: cdc_acm is active
>     Driver Activation Cmd: "modprobe cdc_acm"
>   Config Status: cfg=no, avail=yes, need=no, active=unknown
>   Attached to: #4 (Hub)
>
> 07: USB 00.1: 0000 Unclassified device
>   [Created at usb.122]
>   UDI: /org/freedesktop/Hal/devices/usb_device_1b7d_70a_noserial_if1
>   Unique ID: DrDI.VRkArQ0viUB
>   Parent ID: ADDn.hKbQSFhpkw6
>   SysFS ID: /devices/pci0000:00/0000:00:07.2/usb1/1-1/1-1.1/1-1.1:1.1
>   SysFS BusID: 1-1.1:1.1
>   Hardware Class: unknown
>   Model: "Qualcomm CDMA Technologies MSM"
>   Hotplug: USB
>   Vendor: usb 0x1b7d "Qualcomm, Incorporated"
>   Device: usb 0x070a "Qualcomm CDMA Technologies MSM"
>   Driver: "cdc_acm"
>   Driver Modules: "cdc_acm"
>   Speed: 12 Mbps
>   Module Alias: "usb:v1B7Dp070Ad0000dc02dsc00dp00ic0Aisc00ip00"
>   Config Status: cfg=new, avail=yes, need=no, active=unknown
>   Attached to: #4 (Hub)

Hi Nidek,

I can see 2 USB Qualcomm CDMA device in the hwinfo, which one are u
using as the modem here? My hwinfo is given below :
=======================
12: USB 00.0: 0000 Unclassified device
  [Created at usb.122]
  UDI: /org/freedesktop/Hal/devices/usb_device_5c6_6000_noserial_if0
  Unique ID: mZxt.PmV7noyU267
  Parent ID: uIhY.o51ScQgU3Z5
  SysFS ID: /devices/pci0000:00/0000:00:1d.0/usb3/3-2/3-2:1.0
  SysFS BusID: 3-2:1.0
  Hardware Class: unknown
  Model: "Qualcomm ZTE CDMA Tech"
  Hotplug: USB
  Vendor: usb 0x05c6 "Qualcomm, Inc."
  Device: usb 0x6000 "ZTE CDMA Tech"
  Speed: 12 Mbps
  Module Alias: "usb:v05C6p6000d0000dc00dsc00dp00icFFiscFFipFF"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #5 (Hub)
=====================

I was also using kinternet, but the same problem was happening with
kinternet. I can connect the first time, and then disconnect. But the
second time the modem doest respond. So i tried using wvdial. Below
are the steps i use to bring up the module

modprobe -v usbserial vendor=0x05c6 product=0x6000
smpppd

Then use kinternet or wvdial to dial out

My device is /dev/ttyUSB0

Regards
-- 
umesh3034
-- 
To unsubscribe, e-mail: opensuse+unsubscribe@xxxxxxxxxxxx
For additional commands, e-mail: opensuse+help@xxxxxxxxxxxx