Mailinglist Archive: opensuse (3605 mails)
| < Previous | Next > |
Re: [SLE] Install of 10.1 - Not Happy!
- From: Andy Goss <aegoss@xxxxxxxxxxxxx>
- Date: Thu, 22 Jun 2006 18:34:03 +1000
- Message-id: <1150965243.3420.27.camel@xxxxxxxxxxxxxxxxxxxxx>
On Tue, 2006-06-13 at 16:56 +0200, Per Jessen wrote:
> Andy Goss wrote:
>
> > Prior to converting to Linux, I established that the one and only
> > video card is an "Intel 82845G/GL/GE/PE/GV Graphics Controller
> > Revision 003". sax2 -p shows me an Intel i845 (plus some numbers I did
> > not note down, I am currently in FC4 which has not heard of sax2)
> > FC4's hardware browser shows me an "Intel 82845G/GL[Brookdale-G]/GE
> > Chipset Integrated Graphics Device".
>
> lspci will show you exactly what kind of chip you've got installed.
>
> What does "hwinfo --framebuffer" say?
>
> You could also try configuring the card manually using sax2 - just run
> "sax2 -r". I would expect to see some error messages - also
> check /var/log/Sax.log - that might have some clues.
>
> All of this would also be good diags for a bugreport if it turns out
> your graphics card/chip really isn't supported.
>
>
> /Per Jessen, Zürich
>
>
******* Both "live" options do the same - give me a command line login
******* lspci -vv shows:
00:02.0 VGA compatible controller: Intel Corporation
82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device (rev 03)
(prog-if 00 [VGA])
Subsystem: Giga-byte Technology Unknown device 2562
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e8100000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
******* hwinfo --all gives:
bios.4.1: vbe infoBus error
******* sax2 -r said:
"
SaX: initializing please wait...
SaX: your current configuration will not be read in
[?25h[?0cSaX: no X-Server is running
SaX: will start own server if needed
"
and then:
"died at /usr/share/sax/init.pl line 619"
which, if the KWrite line number is appropriate, is the "die $result"
line as below:
#==========================================
# sysp -s xstuff
#------------------------------------------
$querystr = "xstuff";
$subject = "Sysp: XStuff detection data";
$result = qx ($spec{Sysp} -s $querystr);
chomp $result;
Logger ( $subject."\n".$result,$logHandle );
my $xstuffLines = split("\n",$result);
if ($xstuffLines < 3) {
die $result;
}
Debug ( $result );
******* /var/log/Xorg.0.log says:
X Window System Version 6.9.0
Release Date: 21 December 2005
X Protocol Version 11, Revision 0, Release 6.9
Build Operating System: SuSE Linux [ELF] SuSE
Current Operating System: Linux linux-9t89 2.6.16.13-4-default #1 Wed
May 3 04:53:23 UTC 2006 i686
Build Date: 02 May 2006
Before reporting problems, check http://wiki.X.Org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Jun 22 17:21:31 2006
(==) Using config file: "/etc/X11/xorg.conf"
Data incomplete in file /etc/X11/xorg.conf
At least one Device section is required.
(EE) Problem parsing the config file
(EE) Error parsing the config file
Fatal server error:
no screens found
Please consult the The X.Org Foundation support
at http://wiki.X.Org
for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional
information.
(WW) xf86CloseConsole: VT_GETSTATE failed: Bad file descriptor
(WW) xf86CloseConsole: KDSETMODE failed: Bad file descriptor
(WW) xf86CloseConsole: VT_GETMODE failed: Bad file descriptor
******* /var/log/SaX.log contains:
/*************
SaX2 log : SaX2 version 7.1 - SVN Release: 1.49 2003/03/17
**************
SVN RELEASE : 1094
:
DESCRIPTION : X11 configuration log file to collect information
: about detection, startup and configuration.
: There are three parts of logging:
: ---
: 1) INIT ( detection, 3D )
: 2) STARTUP ( xorg.conf, X11 log, glxinfo )
: 3) CONFIG ( config actions )
: ---
:
VERSION : SaX2 compiled for: [SUSE LINUX 10.1 (i586)]
PARAMETER : -r -r
:
LOG DATE : Thu Jun 15 18:46:14 EST 2006
*************/
============================
Framebuffer Info:
----------------------------
Framebuffer is active
15-Jun 18:46:17 <I> Initializing...
15-Jun 18:46:19 <I> [ Sysp: Mouse detection data
Mouse0 => Protocol : explorerps/2
Mouse0 => Device : /dev/input/mice
Mouse0 => Buttons : 5
Mouse0 => Wheel : 1
Mouse0 => Emulate : 0
Mouse0 => Name : ImPS/2 Generic Wheel Mouse
Mouse0 => VendorID : 0x0210
Mouse0 => DeviceID : 0x0013
Mouse0 => Profile : <undefined>
Mouse0 => RealDevice : /dev/input/event1
Mouse0 => NutShell : 0
]
15-Jun 18:46:19 <I> [ Sysp: Keyboard detection data
Keyboard0 => XkbModel : pc105
Keyboard0 => XkbLayout : gb
Keyboard0 => Name : AT Translated Set 2 keyboard
Keyboard0 => RealDevice : /dev/input/event0
]
15-Jun 18:46:20 <I> [ Sysp: Server detection data
Card0 => DomainId : 0x0
Card0 => BusId : 0x0
Card0 => SlotId : 0x02
Card0 => FuncId : 0x0
Card0 => Vendor : Intel
Card0 => Device : i845
Card0 => VID : 0x8086
Card0 => DID : 0x2562
Card0 => Module : i810
Card0 => BusType : PCI
Card0 => Detected : 1
Card0 => Flag : DEFAULT
Card0 => SUB-VID : 0x1458
Card0 => SUB-DID : 0x2562
Card0 => DrvProfile : Depth24,NoDDC
]
15-Jun 18:46:23 <I> Sysp: XStuff detection data
******* and that's all
Is it worth trying any of the other install options?
******* In the y2log I find the line:
2006-06-12 14:50:21 <2> linux(3782) [qt-ui]
YQUI_x11.cc(loadPredefinedQtTranslations):421 Can't load translations
for predefined Qt dialogs from /usr/lib/qt3/translations/qt_en.qm
and
2006-06-12 18:14:56 <3> linux-9t89(3782) [YCP]
clients/inst_proposal.ycp:396 Write() failed for submodule x11_proposal
******* What conclusions can be drawn from this lot?
--
Andy Goss
--
Check the headers for your unsubscription address
For additional commands send e-mail to suse-linux-e-help@xxxxxxxx
Also check the archives at http://lists.suse.com
Please read the FAQs: suse-linux-e-faq@xxxxxxxx
> Andy Goss wrote:
>
> > Prior to converting to Linux, I established that the one and only
> > video card is an "Intel 82845G/GL/GE/PE/GV Graphics Controller
> > Revision 003". sax2 -p shows me an Intel i845 (plus some numbers I did
> > not note down, I am currently in FC4 which has not heard of sax2)
> > FC4's hardware browser shows me an "Intel 82845G/GL[Brookdale-G]/GE
> > Chipset Integrated Graphics Device".
>
> lspci will show you exactly what kind of chip you've got installed.
>
> What does "hwinfo --framebuffer" say?
>
> You could also try configuring the card manually using sax2 - just run
> "sax2 -r". I would expect to see some error messages - also
> check /var/log/Sax.log - that might have some clues.
>
> All of this would also be good diags for a bugreport if it turns out
> your graphics card/chip really isn't supported.
>
>
> /Per Jessen, Zürich
>
>
******* Both "live" options do the same - give me a command line login
******* lspci -vv shows:
00:02.0 VGA compatible controller: Intel Corporation
82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device (rev 03)
(prog-if 00 [VGA])
Subsystem: Giga-byte Technology Unknown device 2562
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e8100000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
******* hwinfo --all gives:
bios.4.1: vbe infoBus error
******* sax2 -r said:
"
SaX: initializing please wait...
SaX: your current configuration will not be read in
[?25h[?0cSaX: no X-Server is running
SaX: will start own server if needed
"
and then:
"died at /usr/share/sax/init.pl line 619"
which, if the KWrite line number is appropriate, is the "die $result"
line as below:
#==========================================
# sysp -s xstuff
#------------------------------------------
$querystr = "xstuff";
$subject = "Sysp: XStuff detection data";
$result = qx ($spec{Sysp} -s $querystr);
chomp $result;
Logger ( $subject."\n".$result,$logHandle );
my $xstuffLines = split("\n",$result);
if ($xstuffLines < 3) {
die $result;
}
Debug ( $result );
******* /var/log/Xorg.0.log says:
X Window System Version 6.9.0
Release Date: 21 December 2005
X Protocol Version 11, Revision 0, Release 6.9
Build Operating System: SuSE Linux [ELF] SuSE
Current Operating System: Linux linux-9t89 2.6.16.13-4-default #1 Wed
May 3 04:53:23 UTC 2006 i686
Build Date: 02 May 2006
Before reporting problems, check http://wiki.X.Org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Jun 22 17:21:31 2006
(==) Using config file: "/etc/X11/xorg.conf"
Data incomplete in file /etc/X11/xorg.conf
At least one Device section is required.
(EE) Problem parsing the config file
(EE) Error parsing the config file
Fatal server error:
no screens found
Please consult the The X.Org Foundation support
at http://wiki.X.Org
for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional
information.
(WW) xf86CloseConsole: VT_GETSTATE failed: Bad file descriptor
(WW) xf86CloseConsole: KDSETMODE failed: Bad file descriptor
(WW) xf86CloseConsole: VT_GETMODE failed: Bad file descriptor
******* /var/log/SaX.log contains:
/*************
SaX2 log : SaX2 version 7.1 - SVN Release: 1.49 2003/03/17
**************
SVN RELEASE : 1094
:
DESCRIPTION : X11 configuration log file to collect information
: about detection, startup and configuration.
: There are three parts of logging:
: ---
: 1) INIT ( detection, 3D )
: 2) STARTUP ( xorg.conf, X11 log, glxinfo )
: 3) CONFIG ( config actions )
: ---
:
VERSION : SaX2 compiled for: [SUSE LINUX 10.1 (i586)]
PARAMETER : -r -r
:
LOG DATE : Thu Jun 15 18:46:14 EST 2006
*************/
============================
Framebuffer Info:
----------------------------
Framebuffer is active
15-Jun 18:46:17 <I> Initializing...
15-Jun 18:46:19 <I> [ Sysp: Mouse detection data
Mouse0 => Protocol : explorerps/2
Mouse0 => Device : /dev/input/mice
Mouse0 => Buttons : 5
Mouse0 => Wheel : 1
Mouse0 => Emulate : 0
Mouse0 => Name : ImPS/2 Generic Wheel Mouse
Mouse0 => VendorID : 0x0210
Mouse0 => DeviceID : 0x0013
Mouse0 => Profile : <undefined>
Mouse0 => RealDevice : /dev/input/event1
Mouse0 => NutShell : 0
]
15-Jun 18:46:19 <I> [ Sysp: Keyboard detection data
Keyboard0 => XkbModel : pc105
Keyboard0 => XkbLayout : gb
Keyboard0 => Name : AT Translated Set 2 keyboard
Keyboard0 => RealDevice : /dev/input/event0
]
15-Jun 18:46:20 <I> [ Sysp: Server detection data
Card0 => DomainId : 0x0
Card0 => BusId : 0x0
Card0 => SlotId : 0x02
Card0 => FuncId : 0x0
Card0 => Vendor : Intel
Card0 => Device : i845
Card0 => VID : 0x8086
Card0 => DID : 0x2562
Card0 => Module : i810
Card0 => BusType : PCI
Card0 => Detected : 1
Card0 => Flag : DEFAULT
Card0 => SUB-VID : 0x1458
Card0 => SUB-DID : 0x2562
Card0 => DrvProfile : Depth24,NoDDC
]
15-Jun 18:46:23 <I> Sysp: XStuff detection data
******* and that's all
Is it worth trying any of the other install options?
******* In the y2log I find the line:
2006-06-12 14:50:21 <2> linux(3782) [qt-ui]
YQUI_x11.cc(loadPredefinedQtTranslations):421 Can't load translations
for predefined Qt dialogs from /usr/lib/qt3/translations/qt_en.qm
and
2006-06-12 18:14:56 <3> linux-9t89(3782) [YCP]
clients/inst_proposal.ycp:396 Write() failed for submodule x11_proposal
******* What conclusions can be drawn from this lot?
--
Andy Goss
--
Check the headers for your unsubscription address
For additional commands send e-mail to suse-linux-e-help@xxxxxxxx
Also check the archives at http://lists.suse.com
Please read the FAQs: suse-linux-e-faq@xxxxxxxx
| < Previous | Next > |