Mailinglist Archive: opensuse (4398 mails)

["Raul H. Lapitzondo" <Raul.Lapitzondo@xxxxxxxxxxxxxxxxx>]

Hi Ken !.

In another partition of the disc I have installed XP, with which I can 
connect without problems obtaining the IP of the DHCP, I do not 
understand where it is the problem :(

Regards
Raul

Ken Hough escribió:

> Raul,
>
> 'ifup' and 'ifdown' work for me. I use DHCP via the router.
>
> I'm not an expert wrt wifi (or indeed wrt Linux) and have not set up 
> WEP yet. My only access control is SSID.
>
> Have you tried disabling all access control? Can you then get IP via 
> DHCP. Is the firewall getting in the way?
>
> On screen messages during setup of my wifi card often suggest that 
> DHCP has not been successful, but after a few seconds LEDs on wifi 
> card indicate an active link and 'ifconfig' confirms setup (named as 
> 'ath0' in my case).
>
> My router is a NETGEAR DG834GT and wifi card a WG511T. I'm running 
> SuSE v9.1
>
> Ken Hough
>
> Raul H. Lapitzondo wrote:
>
> > Hi Ken, I already did it but it does not work :)
> >
> > Ken Hough escribió:
> >
> > > Raul,
> > >
> > > I don't know if it is relevant, but I had problems with my laptop PC 
> > > when I had both ethernet and wifi running together.
> > >
> > > I overcame this by arranging for these interfaces to be started 
> > > manually  only as and when required. This is in the advanced 
> > > settings under YAST.
> > >
> > > Then it is necessary only to use the commands 'ifup eth0' and 
> > > 'ifdown eth0', etc
> > >
> > > Ken Hough
> > >
> > >
> > > Raul H. Lapitzondo wrote:
> > >
> > > > I have a wireless card (PCMCIA) Dlink G630 (B1), running in SuSE 
> > > > 9.3. The card is recognizied, but I cannot connect to internet.
> > > > The authentication metod is WEP (128 bits). I configure whith YOU 
> > > > and i try to connect whith Kinternet.
> > > >
> > > > I have not had good results, apparently appears as associate but it 
> > > > does not obtain from router (DHCP) the IP.
> > > >
> > > >
> > > > Also them comment that previously with other router with wep of 64 
> > > > bits I could make work it. I clarify this last one by the 
> > > > compatibility of the wireless card.
> > > >
> > > >
> > > > to continuation the configuration files:
> > > >
> > > > notebook_linux:/etc/sysconfig/network # cat 
> > > > ifcfg-wlan-bus-pci-0000\:03\:00.0
> > > > MTU=''
> > > > NAME='D-Link ACX 111 54Mbps Wireless Interface'
> > > > REMOTE_IPADDR=''
> > > > STARTMODE='auto'
> > > > UNIQUE='svHJ.oRQZSF2LIrD'
> > > > USERCONTROL='yes'
> > > > WIRELESS_AUTH_MODE='open'
> > > > WIRELESS_KEY_1='F99F43EC7040705036161631B1'
> > > > WIRELESS_KEY_2='712B590BD70D32007043618B32'
> > > > WIRELESS_KEY_3='BD2190CB0EB08757B5CF1C0BE4'
> > > > WIRELESS_NICK=''
> > > > WIRELESS_POWER='no'
> > > > WIRELESS_WPA_PSK=''
> > > > _nm_name='bus-pci-0000:03:00.0'
> > > > WIRELESS_ESSID='MiRed'
> > > > WIRELESS_KEY_0='642BAC0F44F357954C0FB54DBC'
> > > > BOOTPROTO='dhcp'
> > > > WIRELESS_NWID=''
> > > > WIRELESS_KEY=''
> > > > WIRELESS_DEFAULT_KEY='0'
> > > > WIRELESS_KEY_LENGTH='128'
> > > > WIRELESS_AP=''
> > > > WIRELESS_BITRATE='auto'
> > > > WIRELESS_CHANNEL=''
> > > > WIRELESS_MODE='Managed'
> > > > WIRELESS_FREQUENCY=''
> > > >
> > > > ---------------------------------------------------------------------------------------------------------- 
> > > >
> > > > This is the out for restart of the network:
> > > > --------------------------------------------------------------------------------------------------------------------- 
> > > >
> > > > notebook_linux:~ # rcnetwork restart
> > > > Shutting down network interfaces:
> > > >   eth0      device: Broadcom Corporation BCM4401 100Base-T (rev 01)
> > > >   eth0      configuration: eth-id-00:0d:56:35:31:9b                 
> > > > done
> > > >   wlan0     device: Texas Instruments ACX 111 54Mbps Wireless 
> > > > Interface
> > > >   wlan0     configuration: wlan-bus-pci-0000:03:00.0                
> > > > done
> > > > Shutting down service network  .  .  .  .  .  .  .  .  .  .  .  .  
> > > > .  done
> > > > Hint: you may set mandatory devices in /etc/sysconfig/network/config
> > > > Setting up network interfaces:
> > > >   lo
> > > >   lo        IP address: 127.0.0.1/8                                 
> > > > done
> > > >   eth0      device: Broadcom Corporation BCM4401 100Base-T (rev 01)
> > > >   eth0      configuration: eth-id-00:0d:56:35:31:9b
> > > >   eth0      IP address: 192.168.0.100/24                            
> > > > done
> > > >   wlan0     device: Texas Instruments ACX 111 54Mbps Wireless 
> > > > Interface
> > > >   wlan0     configuration: wlan-bus-pci-0000:03:00.0
> > > >   wlan0     (DHCP) . . . . . no IP address yet... backgrounding.    
> > > > waiting
> > > > Setting up service network  .  .  .  .  .  .  .  .  .  .  .  .  .  
> > > > .  done
> > > > SuSEfirewall2: Warning: ip6tables does not support state matching. 
> > > > Extended IPv6 support disabled.
> > > > SuSEfirewall2: Setting up rules from /etc/sysconfig/SuSEfirewall2 ...
> > > > SuSEfirewall2: Firewall rules successfully set
> > > > --------------------------------------------------------------------------------------------------------------------- 
> > > >
> > > >
> > > > and /var/log/messages:
> > > >
> > > > Sep 24 12:05:51 notebook_linux dhcpcd[15471]: terminating on signal 15
> > > > Sep 24 12:05:51 notebook_linux kernel: FIXME: most likely needs 
> > > > refinement, first implementation version only...
> > > > Sep 24 12:05:51 notebook_linux kernel: acx_set_status: Setting 
> > > > status = 0 (STARTED)
> > > > Sep 24 12:05:51 notebook_linux kernel: module count --
> > > > Sep 24 12:05:51 notebook_linux dhcpcd-hook: Skipping 'ifdown 
> > > > $INTERFACE -o dhcp' call
> > > > Sep 24 12:05:55 notebook_linux kernel: module count ++
> > > > Sep 24 12:05:55 notebook_linux kernel: OPENING DEVICE
> > > > Sep 24 12:05:55 notebook_linux kernel: firmware version >= 1.9.3.e 
> > > > --> using S/W timer
> > > > Sep 24 12:05:55 notebook_linux kernel: CodeEnd:11660
> > > > Sep 24 12:05:55 notebook_linux kernel: Setting WEP key: 0 with 
> > > > size: 13
> > > > Sep 24 12:05:55 notebook_linux kernel: Setting WEP key: 1 with 
> > > > size: 13
> > > > Sep 24 12:05:55 notebook_linux kernel: Setting WEP key: 2 with 
> > > > size: 13
> > > > Sep 24 12:05:55 notebook_linux kernel: Setting WEP key: 3 with 
> > > > size: 13
> > > > Sep 24 12:05:55 notebook_linux kernel: setting active default WEP 
> > > > key number: 0.
> > > > Sep 24 12:05:55 notebook_linux kernel: initial settings update on 
> > > > iface activation.
> > > > Sep 24 12:05:55 notebook_linux kernel: get_mask 0x00000000, 
> > > > set_mask 0x0007cefc
> > > > Sep 24 12:05:55 notebook_linux kernel: important setting has been 
> > > > changed --> need to update packet templates, too
> > > > Sep 24 12:05:55 notebook_linux kernel: acx_set_status: Setting 
> > > > status = 0 (STARTED)
> > > > Sep 24 12:05:55 notebook_linux kernel: Updating WEP key settings
> > > > Sep 24 12:05:55 notebook_linux kernel: Setting WEP key: 0 with 
> > > > size: 13
> > > > Sep 24 12:05:55 notebook_linux kernel: Setting WEP key: 1 with 
> > > > size: 13
> > > > Sep 24 12:05:55 notebook_linux kernel: Setting WEP key: 2 with 
> > > > size: 13
> > > > Sep 24 12:05:55 notebook_linux kernel: Setting WEP key: 3 with 
> > > > size: 13
> > > > Sep 24 12:05:55 notebook_linux kernel: Setting WEP key 0 as default.
> > > > Sep 24 12:05:55 notebook_linux kernel: Updating transmit power: 15 dBm
> > > > Sep 24 12:05:56 notebook_linux kernel: Updating antenna value: 0x4A
> > > > Sep 24 12:05:56 notebook_linux kernel: Configure Command 0x100B not 
> > > > supported under acx111 (yet)
> > > > Sep 24 12:05:56 notebook_linux kernel: Updating Energy Detect (ED) 
> > > > threshold: 0
> > > > Sep 24 12:05:56 notebook_linux kernel: Configure Command 0x100F not 
> > > > supported under acx111 (yet)
> > > > Sep 24 12:05:56 notebook_linux kernel: Updating Channel Clear 
> > > > Assessment (CCA) value: 0x00
> > > > Sep 24 12:05:56 notebook_linux kernel: Configure Command 0x100E not 
> > > > supported under acx111 (yet)
> > > > Sep 24 12:05:56 notebook_linux kernel: Updating: enable Tx
> > > > Sep 24 12:05:56 notebook_linux kernel: Updating: enable Rx on 
> > > > channel: 11
> > > > Sep 24 12:05:56 notebook_linux kernel: Updating regulatory domain: 
> > > > 0x30
> > > > Sep 24 12:05:56 notebook_linux kernel: setting RXconfig to 2050:0fdd
> > > > Sep 24 12:05:56 notebook_linux kernel: Starting radio scan
> > > > Sep 24 12:05:56 notebook_linux kernel: acx_set_status: Setting 
> > > > status = 1 (SCANNING)
> > > > Sep 24 12:05:56 notebook_linux kernel: <acx_set_timer> Elapse = 
> > > > 2500000
> > > > Sep 24 12:05:56 notebook_linux kernel: attempt to set the timer 
> > > > when the card interface is not up!
> > > > Sep 24 12:05:57 notebook_linux kernel: Updating channel: 11
> > > > Sep 24 12:05:57 notebook_linux kernel: get_mask 0x00000000, 
> > > > set_mask 0x00000000 - after update
> > > > Sep 24 12:05:57 notebook_linux kernel: FIXME: most likely needs 
> > > > refinement, first implementation version only...
> > > > Sep 24 12:05:57 notebook_linux kernel: FIXME: most likely needs 
> > > > refinement, first implementation version only...
> > > > Sep 24 12:05:57 notebook_linux kernel: FIXME: most likely needs 
> > > > refinement, first implementation version only...
> > > > Sep 24 12:05:57 notebook_linux kernel: FIXME: most likely needs 
> > > > refinement, first implementation version only...
> > > > Sep 24 12:05:57 notebook_linux kernel: FIXME: most likely needs 
> > > > refinement, first implementation version only...
> > > > Sep 24 12:05:57 notebook_linux kernel: get_mask 0x00000000, 
> > > > set_mask 0x00000040
> > > > Sep 24 12:05:57 notebook_linux kernel: setting RXconfig to 2050:0fdd
> > > > Sep 24 12:05:57 notebook_linux kernel: get_mask 0x00000000, 
> > > > set_mask 0x00000000 - after update
> > > > Sep 24 12:05:57 notebook_linux kernel: FIXME: most likely needs 
> > > > refinement, first implementation version only...
> > > > Sep 24 12:05:57 notebook_linux kernel: get_mask 0x00000000, 
> > > > set_mask 0x00000040
> > > > Sep 24 12:05:57 notebook_linux kernel: setting RXconfig to 2050:0fdd
> > > > Sep 24 12:05:57 notebook_linux kernel: get_mask 0x00000000, 
> > > > set_mask 0x00000000 - after update
> > > > Sep 24 12:05:57 notebook_linux kernel: FIXME: most likely needs 
> > > > refinement, first implementation version only...
> > > > Sep 24 12:05:57 notebook_linux kernel: get_mask 0x00000000, 
> > > > set_mask 0x00000040
> > > > Sep 24 12:05:58 notebook_linux kernel: setting RXconfig to 2050:0fdd
> > > > Sep 24 12:05:58 notebook_linux kernel: get_mask 0x00000000, 
> > > > set_mask 0x00000000 - after update
> > > > Sep 24 12:05:58 notebook_linux kernel: acx_process_probe_response: 
> > > > found and registered station 0: ESSID "MiRed" on channel 11, BSSID 
> > > > 00:13:10:24:68:1A, Access Point/54Mbps, Caps 0x0031, SIR 13, SNR 0.
> > > > Sep 24 12:05:58 notebook_linux kernel: Got Info IRQ: status 0x1001, 
> > > > type 0x0001: scan complete
> > > > Sep 24 12:05:58 notebook_linux kernel: Radio scan found 1 stations 
> > > > in this area.
> > > > Sep 24 12:05:58 notebook_linux kernel: <Scan Table> 0: 
> > > > SSID="MiRed",CH=11,SIR=13,SNR=0
> > > > Sep 24 12:05:58 notebook_linux kernel: peer_cap 0x0031, needed_cap 
> > > > 0x0001
> > > > Sep 24 12:05:58 notebook_linux kernel: Found station with matching 
> > > > ESSID!! ("MiRed" station, "MiRed" config)
> > > > Sep 24 12:05:58 notebook_linux kernel: acx_complete_dot11_scan: 
> > > > matching station FOUND (idx 0), JOINING (00 13 10 24 68 1A).
> > > > Sep 24 12:05:58 notebook_linux kernel: acx_join_bssid rates_basic 
> > > > 0x0027, rates_supported 0x1fff
> > > > Sep 24 12:05:58 notebook_linux kernel: <acx_join_bssid> BSS_Type = 2
> > > > Sep 24 12:05:58 notebook_linux kernel: <acx_join_bssid> JoinBSSID 
> > > > MAC:00 13 10 24 68 1A
> > > > Sep 24 12:05:58 notebook_linux kernel: Sending authentication1 
> > > > request, awaiting response!
> > > > Sep 24 12:05:58 notebook_linux kernel: acx_set_status: Setting 
> > > > status = 2 (WAIT_AUTH)
> > > > Sep 24 12:05:58 notebook_linux kernel: <acx_set_timer> Elapse = 
> > > > 1500000
> > > > Sep 24 12:05:58 notebook_linux kernel: acx_process_authen: UNVERIFIED.
> > > > Sep 24 12:05:59 notebook_linux kernel: 00:0F:3D:52:7D:AE 
> > > > <4>00:0F:3D:52:7D:AE <4>00:13:10:24:68:1A <4>00:13:10:24:68:1A 
> > > > <4>00:13:10:24:68:1A
> > > > Sep 24 12:05:59 notebook_linux kernel: Algorithm is ok
> > > > Sep 24 12:05:59 notebook_linux kernel: Got current client for sta 
> > > > hash tab
> > > > Sep 24 12:05:59 notebook_linux kernel: Found acceptable client
> > > > Sep 24 12:05:59 notebook_linux kernel: <acx_sta_list_add> sta = 
> > > > 00:13:10:24:68:1A
> > > > Sep 24 12:05:59 notebook_linux kernel: acx_process_authen auth seq 
> > > > step 2.
> > > > Sep 24 12:05:59 notebook_linux kernel: acx_set_status: Setting 
> > > > status = 3 (AUTHENTICATED)
> > > > Sep 24 12:05:59 notebook_linux kernel: <acx_set_timer> Elapse = 
> > > > 1500000
> > > > Sep 24 12:05:59 notebook_linux kernel: Sending association request, 
> > > > awaiting response! NOT ASSOCIATED YET.
> > > > Sep 24 12:05:59 notebook_linux kernel: association: requesting 
> > > > capabilities 0x0021
> > > > Sep 24 12:05:59 notebook_linux kernel: acx_set_status: Setting 
> > > > status = 4 (ASSOCIATED)
> > > > Sep 24 12:05:59 notebook_linux kernel: ASSOCIATED!
> > > > Sep 24 12:05:59 notebook_linux kernel: acx_timer: status = 4
> > > > Sep 24 12:06:00 notebook_linux SuSEfirewall2: Warning: ip6tables 
> > > > does not support state matching. Extended IPv6 support disabled.
> > > > Sep 24 12:06:00 notebook_linux SuSEfirewall2: Setting up rules from 
> > > > /etc/sysconfig/SuSEfirewall2 ...
> > > > Sep 24 12:06:01 notebook_linux SuSEfirewall2: Firewall rules 
> > > > successfully set
> > > > Sep 24 12:06:02 notebook_linux kernel: eth0: no IPv6 routers present
> > > > Sep 24 12:06:05 notebook_linux kernel: wlan0: no IPv6 routers present
> > > >
> > > > --------------------------------------------------------------------------------------------------------------------- 
> > > >
> > > >
> > > > Best Regards
> > > > Raul