I had the same problem and four days ago I finally can resolved. You have to desactived the SuSEplugger before you want to burn cd's, and if you use k3b you have to select DAO write mode not auto. I wish this works for you, Diana P. P.D. Sorry for my English, but I'm still learning. El jue, 01-04-2004 a las 04:01, Pagan escribió:
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
I am still unable to burn cd's at all. I have replaced the burner and can successfully burn dvd-/+ formats. However, cds will NOT burn.
I've compiled latest cdrtools from sources, tried suse's binaries, even the cdrecord-ProDVD binaries.
The burner is an LG 4081b connected to the secondary IDE cable as master using scsi emu (/dev/sr0) This same system burned cd's succesfully prior to update to 9.0 Anyone have any suggestions? Log file follows: System - ----------------------- K3b Version: 0.11.6 KDE Version: 3.2.1 QT Version: 3.3.1
cdrecord - ----------------------- scsidev: '1,0,0' scsibus: 1 target: 0 lun: 0 Linux sg driver version: 3.1.25 SCSI buffer size: 64512 /opt/schily/bin/cdrecord: This version of cdrecord does not include DVD-R/DVD-RW support code. /opt/schily/bin/cdrecord: If you need DVD-R/DVD-RW support, ask the Author for cdrecord-ProDVD. /opt/schily/bin/cdrecord: Free test versions and free keys for personal use are at ftp://ftp.berlios.de/pub/cdrecord/ProDVD/ Cdrecord-Clone 2.01a27 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling TOC Type: 0 = CD-DA Using libscg version 'schily-0.8'. Driveropts: 'burnfree' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'HL-DT-ST' Identifikation : 'DVDRAM GSA-4081B' Revision : 'A100' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: 0x000A Profile: 0x0012 Profile: 0x0011 Profile: 0x0014 Profile: 0x0013 Profile: 0x001A Profile: 0x001B Profile: 0x0010 Profile: 0x0009 Profile: 0x000A (current) Profile: 0x0008 Profile: 0x0002 Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1204224 = 1176 KB FIFO size : 4194304 = 4096 KB pregap1: -1 Track 01: audio 36 MB (03:39.00) no preemp copy Track 02: audio 40 MB (04:01.36) no preemp copy Track 03: audio 33 MB (03:19.93) no preemp copy Track 04: audio 45 MB (04:28.32) no preemp copy Track 05: audio 32 MB (03:10.74) no preemp copy Track 06: audio 47 MB (04:42.14) no preemp copy Track 07: audio 44 MB (04:21.58) no preemp copy Track 08: audio 39 MB (03:54.05) no preemp copy Track 09: audio 37 MB (03:44.44) no preemp copy Track 10: audio 42 MB (04:11.40) no preemp copy Track 11: audio 55 MB (05:27.13) no preemp copy Total size: 454 MB (45:00.12) = 202509 sectors Lout start: 454 MB (45:02/09) = 202509 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Reference speed: 2 Is not unrestricted Is erasable ATIP start of lead in: -11635 (97:26/65) ATIP start of lead out: 337350 (75:00/00) 1T speed low: 0 (reserved val 0) 1T speed high: 4 2T speed low: 8 2T speed high: 0 (reserved val 10) power mult factor: 4 6 recommended erase/write power: 3 A1 values: 02 4C B0 A2 values: 4A C8 06 Disk type: Phase change Manuf. index: 3 Manufacturer: CMC Magnetics Corporation Blocks total: 337350 Blocks current: 337350 Blocks remaining: 134841 Starting to write CD/DVD at speed 4 in real SAO mode for single session. Last chance to quit, starting real write in 2 seconds. 1 seconds. 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. BURN-Free is OFF. Turning BURN-Free on Performing OPC... /opt/schily/bin/cdrecord: WARNING: Drive returns wrong startsec (0) using -150 Sending CUE sheet... /opt/schily/bin/cdrecord: Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 FF FF FF 6A 00 00 1B 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 05 00 00 00 00 10 2A 00 00 90 30 05 00 00 Sense Key: 0x5 Illegal Request, Segment 0 Sense Code: 0x30 Qual 0x05 (cannot write medium - incompatible format) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 0.002s timeout 200s /opt/schily/bin/cdrecord: Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 00 00 00 00 00 00 1B 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 05 00 00 00 00 10 2A 00 00 90 30 05 00 00 Sense Key: 0x5 Illegal Request, Segment 0 Sense Code: 0x30 Qual 0x05 (cannot write medium - incompatible format) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 0.002s timeout 200s /opt/schily/bin/cdrecord: A write error occured. /opt/schily/bin/cdrecord: Please properly read the error message above. Writing pregap for track 1 at -150 write track pad data: error after 0 bytes BFree: 1176 K BSize: 1176 K Starting new track at sector: 0 Track 01: 0 of 36 MB written. write track data: error after 0 bytes Writing time: 71.262s Average write speed 37.9x. Fixating... Fixating time: 0.016s /opt/schily/bin/cdrecord: fifo had 64 puts and 1 gets. /opt/schily/bin/cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
cdrecord comand: - ----------------------- /opt/schily/bin/cdrecord -v gracetime=2 dev=1,0,0 speed=4 -dao driveropts=burnfree -eject fs=4m -overburn -useinfo -pad -shorttrack - -audio /tmp/kde-root/k3b_audio_0_01.wav /tmp/kde-root/k3b_audio_0_02.wav /tmp/kde-root/k3b_audio_0_03.wav /tmp/kde-root/k3b_audio_0_04.wav /tmp/kde-root/k3b_audio_0_05.wav /tmp/kde-root/k3b_audio_0_06.wav /tmp/kde-root/k3b_audio_0_07.wav /tmp/kde-root/k3b_audio_0_08.wav /tmp/kde-root/k3b_audio_0_09.wav /tmp/kde-root/k3b_audio_0_10.wav /tmp/kde-root/k3b_audio_0_11.wav
-----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.2 (GNU/Linux)
iD8DBQFAa9qH9EKgVX3zIJ4RAqblAJsG2FDB0d5PSpVARi/NFUooVxeSSwCfXHeK Px1VWhNxAmFcMexeNHdKxrs= =Xstl -----END PGP SIGNATURE-----