Mailinglist Archive: opensuse (2773 mails)

[rshakin@xxxxxxxxxxxxxxxxxxx (Roman Shakin)]

Ok ppl this is what i have 

NetForce:~ # isapnp /etc/isapnp.config 
Board 1 has Identity 81 ff ff ff ff 20 00 a8 65:  YMH0020 Serial No -1
[checksum 81]
Board 2 has Identity 3e 46 46 46 46 06 20 68 04:  ACH2006 Serial No
1179010630 [checksum 3e]
ACH2006/1179010630[0]{5634BTV 56K FDSP Voice Modem                 }: Port
0x2E8; IRQ3 --- Enabled OK
NetForce:~ #
 
-------------->This is my PNP ISA config or atleast what it says when i
run it 

this is my serial port config
NetForce:~ # setserial /dev/ttyS1
/dev/ttyS1, UART: 16550A, Port: 0x02f8, IRQ: 3
NetForce:~ # setserial /dev/ttyS2
/dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4
NetForce:~ # setserial /dev/ttyS3
/dev/ttyS3, UART: 16550A, Port: 0x02e8, IRQ: 3
NetForce:~ # setserial /dev/ttyS4
/dev/ttyS4, UART: unknown, Port: 0x01a0, IRQ: 2, Flags: Fourport
NetForce:~ # setserial /dev/ttyS5
/dev/ttyS5, UART: unknown, Port: 0x01a8, IRQ: 2, Flags: Fourport
NetForce:~ # setserial /dev/ttyS6
/dev/ttyS6, UART: unknown, Port: 0x01b0, IRQ: 2, Flags: Fourport
NetForce:~ # setserial /dev/ttyS7
/dev/ttyS7, UART: unknown, Port: 0x01b8, IRQ: 2, Flags: Fourport
NetForce:~ # setserial /dev/ttyS8
/dev/ttyS8, UART: unknown, Port: 0x02a0, IRQ: 5, Flags: Fourport
NetForce:~ # setserial /dev/ttyS9
/dev/ttyS9, UART: unknown, Port: 0x02a8, IRQ: 5, Flags: Fourport
NetForce:~ # setserial /dev/ttyS10
/dev/ttyS10, UART: unknown, Port: 0x02b0, IRQ: 5, Flags: Fourport
NetForce:~ #

------------->and this is my isapnp.config file 

# $Id: pnpdump.c,v 1.18 1999/02/14 22:47:18 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0203
# Board 1 has serial identifier 81 ff ff ff ff 20 00 a8 65
# Board 2 has serial identifier 3e 46 46 46 46 06 20 68 04

# (DEBUG)
(READPORT 0x0203)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING

# Card 1: (serial identifier 81 ff ff ff ff 20 00 a8 65)
# Vendor Id YMH0020, No Serial Number (-1), checksum 0x81.
# Version 1.0, Vendor version 0.0
# ANSI string -->OPL3-SAX Sound Board<--
#
# Logical device id YMH0021
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE YMH0020/-1 (LD 0

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0220
#             IO base alignment 16 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0530
#             Maximum IO base address 0x0530
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0530))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0330
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 3 (SIZE 2) (BASE 0x0330))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0370
#             Maximum IO base address 0x0370
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 4 (SIZE 2) (BASE 0x0370))
#       IRQ 5.
#             High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 1.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 1 (CHANNEL 1))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0240
#             Maximum IO base address 0x0240
#             IO base alignment 16 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0240))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0e80
#             Maximum IO base address 0x0e80
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0e80))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 8 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0300
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 3 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x0ffe
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 4 (SIZE 2) (BASE 0x0100))
#       IRQ 5, 7, 9, 10 or 11.
#             High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 1 (CHANNEL 0))

#       Start dependent functions: priority functional
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 16 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0530
#             Maximum IO base address 0x0f48
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0530))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0334
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 3 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x0ffe
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 4 (SIZE 2) (BASE 0x0100))
#       IRQ 3, 5, 7, 9, 10 or 11.
#             High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 1 (CHANNEL 0))

#     End dependent functions
 (NAME "YMH0020/-1[0]{OPL3-SAX Sound Board}")
# (ACT Y)
))
#
# Logical device id YMH0022
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE YMH0020/-1 (LD 1
#     Compatible device id PNPb02f

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0201
#             Maximum IO base address 0x0201
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0201))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0202
#             Maximum IO base address 0x0202
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0202))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0203
#             Maximum IO base address 0x0203
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0203))

#       Start dependent functions: priority functional
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0204
#             Maximum IO base address 0x020f
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0204))

#     End dependent functions
 (NAME "YMH0020/-1[1]{OPL3-SAX Sound Board}")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Card 2: (serial identifier 3e 46 46 46 46 06 20 68 04)
# Vendor Id ACH2006, Serial Number 1179010630, checksum 0x3E.
#     Version 1.0, Vendor version 0.0
#     ANSI string -->5634BTV 56K FDSP Voice Modem                 <--
#
# Logical device id ACH5600
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE ACH2006/1179010630 (LD 0

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Fixed IO base address 0x02f8
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02f8))
#       IRQ 3.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Fixed IO base address 0x03f8
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03f8))
#       IRQ 4.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 4 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Fixed IO base address 0x03e8
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03e8))
#       IRQ 3, 4, 5 or 7.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Fixed IO base address 0x02e8
#             Number of IO addresses required: 8
 (IO 0 (SIZE 8) (BASE 0x02e8))
#       IRQ 3, 4, 5 or 7.
#             High true, edge sensitive interrupt (by default)
 (INT 0 (IRQ 3 (MODE +E)))

#     End dependent functions
 (NAME "ACH2006/1179010630[0]{5634BTV 56K FDSP Voice Modem
}")
 (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
 
--------->and this is what wvdial says when i try to dial

NetForce:~ # wvdial
--> WvDial: Internet dialer version 1.20
--> Initializing modem.
--> Sending: ATZ
--> Modem not responding.
NetForce:~ #

---------->and this is my /etc/wvdial.conf

[Dialer Defaults]
Username = rshakin@xxxxxxxxxxxx
Modem = /dev/modem
Password = ******
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 S11=55 +FCLASS=0
Compuserve = 0
Tonline = 0
Dial Command = ATDT
Phone = 00000
Baud = 57600
Auto DNS = 1
Stupid Mode = 1
New PPPD = 1

So if any one has any bright ideas i want to hear them 


-- 
To unsubscribe send e-mail to suse-linux-e-unsubscribe@xxxxxxxx
For additional commands send e-mail to suse-linux-e-help@xxxxxxxx             
Also check the FAQ at http://www.suse.com/Support/Doku/FAQ/