May 2019 - openSUSE Support - openSUSE Mailing Lists

[opensuse-support] Tumbleweed - Clementine always crashing
by mh＠mike.franken.de 10 Jun '19

10 Jun '19

Hi *, any idea, why Clementine on my Tumbleweed machine is crashing always? It runs from a few seconds to one or two hours, but then it is crashing in 10 of 10 cases. No crash information is shown and I find no message, that points to the reason of the crash 8-< TIA. Bye. Michael. -- Michael Hirmke -- To unsubscribe, e-mail: opensuse-support+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-support+owner(a)opensuse.org

2 3

[opensuse-support] Tumbleweed: Updating system after 4 weeks of absence - a few new error messages
by mh＠mike.franken.de 30 May '19

30 May '19

Hi *, after 4 weeks of absence I udated my Tumbleweed system today and got the latest snapshots. Since then, I have a few new error and warning messages in my journal. I could resolve some of them in the meantime, but for the following ones I couldn't find enough information. Can anyone shed some light on them? NetworkManager: --------------- <warn> [1559072807.6962] device (p3p2): connectivity: "/proc/sys/net/ipv4/conf/all/rp_filter" is set to "1". This might break connectivity checking for IPv4 on this device <warn> [1559072807.7006] device (wlp2s0): connectivity: "/proc/sys/net/ipv4/conf/all/rp_filter" is set to "1". This might break connectivity checking for IPv4 on this device <warn> [1559072807.7135] dns-sd-resolved[0x5618dc3848b0]: failed to connect to resolved via DBus: Error calling StartServiceByName for org.freedesktop.resolve1: GDBus.Error:org.freedesktop.systemd1.NoSuchUnit: Unit dbus-org.freedesktop.resolve1.service not found. SDDM: ----- sddm-greeter[2229]: file:///usr/share/sddm/themes/breeze-openSUSE/components/UserDelegate.qml:174: ReferenceError: ColorScope is not defined ... sddm-greeter[2229]: Hunspell dictionary is missing for "en_GB" . Search paths ("/usr/share/qt5/qtvirtualkeyboard/hunspell", "/usr/share/hunspell", "/usr/share/myspell/dicts") sddm-helper[2561]: gkr-pam: unable to locate daemon control file Kernel: ------- kernel: ath10k_pci 0000:02:00.0: unsupported HTC service id: 1536 Thx a lot. Bye. Michael. -- Michael Hirmke -- To unsubscribe, e-mail: opensuse-support+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-support+owner(a)opensuse.org

2 2

[opensuse-support] Excessive log entries on the warning log from empathy.
by Carlos E. R. 27 May '19

27 May '19

Hi, I'm getting thousands of these in the *warn* log. To me they look debug entries, should not be there: <1.4> 2019-05-26 18:59:50 Telcontar org.freedesktop.Telepathy.Client.Empathy.Chat 4258 - - Memory pressure relief: Total: res = 46649344/46649344/0, res+swap = 42369024/42369024/0 <1.4> 2019-05-26 19:00:21 Telcontar org.freedesktop.Telepathy.Client.Empathy.Chat 4258 - - Memory pressure relief: Total: res = 48451584/46649344/-1802240, res+swap = 44171264/44171264/0 <1.4> 2019-05-26 19:00:27 Telcontar org.freedesktop.Telepathy.Client.Empathy.Chat 4258 - - Memory pressure relief: Total: res = 46682112/46649344/-32768, res+swap = 42401792/42401792/0 -- Cheers / Saludos, Carlos E. R. (from 15.0 x86_64 at Telcontar)

3 14

[opensuse-support] Leap 15.1 Problem creating new user
by Bob Williams 26 May '19

26 May '19

This machine was upgraded from Leap 15.0 to 15.1 during the beta testing phase. The upgrade was done by switching all the repos to the 15.1 version, followed by zypper dup. At that time, there were two users on the machine, both of whom continue to be able to login satisfactorily. I have tried to create a third user using the YaST module, and it appears to work, but the new user cannot login. When I enter the password and click Login, the password gets highlighted in blue, and the message 'Login failed' appears. When logged in as a working user, I cannot su to the new user: 09:41 bob@europa:~> su newuser Password: su: Authentication failure Although newuser's home gets created, it is missing some of the default directories, such as ~/Documents, ~/Pictures etc.: bob@europa:~> ls -alh /home/newuser total 40K drwxr-xr-x 7 sysadmin users 251 May 24 17:01 . drwxr-xr-x 5 root root 43 May 24 17:01 .. -rw------- 1 sysadmin users 0 May 18 1996 .bash_history -rw-r--r-- 1 sysadmin users 1.2K Apr 27 20:48 .bashrc drwxr-xr-x 2 sysadmin users 6 Mar 11 16:09 bin drwxr-xr-x 2 sysadmin users 21 Feb 22 18:32 .claws-mail drwx------ 2 sysadmin users 6 Mar 11 16:09 .config -rw-r--r-- 1 sysadmin users 1.6K Apr 9 2018 .emacs drwxr-xr-x 2 sysadmin users 6 Mar 11 16:09 .fonts -rw-r--r-- 1 sysadmin users 73 Jun 7 2018 .i18n -rw-r--r-- 1 sysadmin users 861 Apr 9 2018 .inputrc drwx------ 2 sysadmin users 6 Mar 11 16:09 .local -rw-r--r-- 1 sysadmin users 6.0K Dec 17 22:39 .muttrc -rw-r--r-- 1 sysadmin users 1.1K Apr 27 20:48 .profile -rw-r--r-- 1 sysadmin users 311 Dec 17 14:50 .urlview -rw-r--r-- 1 sysadmin users 2.0K Jun 7 2018 .xim.template -rwxr-xr-x 1 sysadmin users 1.1K Jan 18 08:41 .xinitrc.template Can anyone else confirm this behaviour? -- Bob

5 15

[opensuse-support] Does newmoon crash for everyone trying to use it? on KDE3?
by Felix Miata 12 May '19

12 May '19

# rpm -qa | grep moon newmoon-28.5.0-2.1.x86_64 $ inxi -GxxIS System: Host: myhost Kernel: 4.4.176-96-default x86_64 bits: 64 compiler: gcc v: 4.8.5 Console: tty 4 wm: kwin dm: N/A Distro: openSUSE Leap 42.3 Graphics: Device-1: Intel 4th Generation Core Processor Family Integrated Graphics vendor: Micro-Star MSI driver: i915 v: kernel bus ID: 00:02.0 chip ID: 8086:041e Display: server: X.Org 1.18.3 driver: modesetting unloaded: fbdev,vesa alternate: intel resolution: 1920x1200~60Hz OpenGL: renderer: Mesa DRI Intel Haswell v: 4.3 Mesa 17.0.5 compat-v: 3.0 direct render: Yes Info: Processes: 277 Uptime: 11:59am up 9 days 21:41, 3 users, load average: 0.36, 0.43, 0.41 Memory: 15.54 GiB used: 5.89 GiB (37.9%) Init: systemd v: 228 runlevel: 5 target: multi-user.target Compilers: gcc: 4.8.5 alt: 4.8 Shell: bash v: 4.3.48 running in: konsole inxi: 3.0.34$ newmoon [3455] ###!!! ABORT: X_CreatePixmap: BadAlloc (insufficient resources for operation); 4 requests ago: file /home/abuild/rpmbuild/BUILD/UXP-PM28.5.0_Release/toolkit/xre/nsX11ErrorHandler.cpp, line 134 [3455] ###!!! ABORT: X_CreatePixmap: BadAlloc (insufficient resources for operation); 4 requests ago: file /home/abuild/rpmbuild/BUILD/UXP-PM28.5.0_Release/toolkit/xre/nsX11ErrorHandler.cpp, line 134 Segmentation fault (core dumped) Segfault results from clicking anything on the main menu bar. -- Evolution as taught in public schools is religion, not science. Team OS/2 ** Reg. Linux User #211409 ** a11y rocks! Felix Miata *** http://fm.no-ip.com/ -- To unsubscribe, e-mail: opensuse-support+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-support+owner(a)opensuse.org

2 3

[opensuse-support] [Leap 15] Apache server on localhost - file ownership?
by Bob Williams 12 May '19

12 May '19

I want to make a copy of my Joomla website to run on my local machine here, so that I can experiment with new modules and settings in a safe environment before committing them to the active site. I have set up a LAMP server - It works! I have copied all the files from the remote server to /srv/www/htdocs/mydomain using wget. I have exported the mysql database with phpMyAdmin and imported it into the local mysql(mariadb) database server. I have edited the configuration files to suit the new environment (I don't rule out some errors here) When I try to visit http://localhost/mydomain in Firefox, I just get a white page (Object not found). Initially, I had root:root owning all the files, but when that didn't work I tried changing it to wwwrun:wwwrun. But that didn't help either. ISTR reading that in this situation, the Apache webserver should own the files, but I don't know what (s)he's called on Leap 15. Any suggestions? I've already googled and searched the Joomla forums. Many thanks Bob -- Bob Williams System: Linux 4.12.14-lp150.12.58-default Desktop: KDE Frameworks: 5.45.0, Qt: 5.9.4 and Plasma: 5.12.5

3 11

[opensuse-support] Sorting BCM20702 Bluetooth dongles
by Robert T Hardy 04 May '19

04 May '19

In /lib/firmware/brcm/ I currently have: -rw-r--r-- 1 root root 34700 Oct 24 2018 BCM20702A0-0a5c-21e8.hcd~ -rw-r--r-- 1 root root 34997 Dec 23 23:07 BCM20702A1-05ac-21e1.hcd -rw-r--r-- 1 root root 35042 Dec 23 23:07 BCM20702A1-0a5c-21e6.hcd -rw-r--r-- 1 root root 35934 Oct 24 2018 BCM20702A1-0a5c-21e8.hcd~ -rw-r--r-- 1 root root 35000 Dec 23 23:07 BCM20702A1-0b05-17cb.hcd -rw-r--r-- 1 root root 35127 Dec 23 23:07 BCM20702A1-0b05-17cf.hcd where the ones without the tilde are from package bcm20702a1-firmware . I use one of them, BCM20702A1-0b05-17cb.hcd, with an ASUSTek Computer, Inc. Broadcom BCM20702A0 Bluetooth dongle, and it works fine, excepting occasional weird interactions with an Android phone. I may want to get into that later. The other two are an attempt to provide firmware to a Broadcom Corp. BCM20702A0 Bluetooth 4.0 dongle. The A0 version is old; I don't remember where I got it; it may have come out of the box, but no matter, because there is no attempt made to load it, even when untilded. The A1 version comes from https://github.com/winterheart/broadcom-bt-firmware/ blob/master/brcm/BCM20702A1-0a5c-21e8.hcd . That one loads just fine, and disables the Bluetooth dongle as shown by: sgt:/lib/firmware/brcm # hciconfig -a hci0: Type: Primary Bus: USB BD Address: 00:02:72:DA:29:9C ACL MTU: 1021:8 SCO MTU: 64:1 DOWN RX bytes:3380 acl:0 sco:0 events:410 errors:0 TX bytes:36343 acl:0 sco:0 commands:409 errors:0 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT hci1: Type: Primary Bus: USB BD Address: 5C:F3:70:80:A0:29 ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING PSCAN RX bytes:263513266 acl:907311 sco:1675 events:233331 errors:0 TX bytes:50912616 acl:465265 sco:1671 commands:254 errors:0 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'sgt.decathlon.org' Class: 0x1c010c Service Classes: Rendering, Capturing, Object Transfer Device Class: Computer, Laptop HCI Version: 4.0 (0x6) Revision: 0x15bb LMP Version: 4.0 (0x6) Subversion: 0x220e Manufacturer: Broadcom Corporation (15) and sgt:/lib/firmware/brcm # hciconfig hci0 up Can't init device hci0: Invalid request code (56) However, if I disable the firmware (with the tilde), then the dongle appears to work: sgt:/lib/firmware/brcm # hciconfig -a hci1: Type: Primary Bus: USB BD Address: 00:02:72:DA:29:9C ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING PSCAN ISCAN RX bytes:4018971 acl:17398 sco:0 events:6779 errors:0 TX bytes:1500425 acl:13379 sco:1 commands:55 errors:0 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'sgt.decathlon.org' Class: 0x1c010c Service Classes: Rendering, Capturing, Object Transfer Device Class: Computer, Laptop HCI Version: 4.0 (0x6) Revision: 0x1000 LMP Version: 4.0 (0x6) Subversion: 0x220e Manufacturer: Broadcom Corporation (15) hci0: Type: Primary Bus: USB BD Address: 5C:F3:70:80:A0:29 ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING PSCAN ISCAN RX bytes:4750 acl:54 sco:0 events:305 errors:0 TX bytes:37328 acl:60 sco:0 commands:238 errors:0 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'sgt.decathlon.org #1' Class: 0x1c010c Service Classes: Rendering, Capturing, Object Transfer Device Class: Computer, Laptop HCI Version: 4.0 (0x6) Revision: 0x15bb LMP Version: 4.0 (0x6) Subversion: 0x220e Manufacturer: Broadcom Corporation (15) This is despite the message from the log: May 04 17:36:54 sgt.decathlon.org kernel: bluetooth hci1: Direct firmware load for brcm/BCM20702A1-0a5c-21e8.hcd failed with error -2 So I guess my first burning question is, is firmware loading necessary to the operation of my bluetooth dongle, or is it only necessary if you want up-to- date firmware. :-) Some other questions revolve around whether the bluetooth stack (and KDE, which I typically use) are up to handling two dongles, since the unplugging of the Broadcom dongle seems to disrupt the operation of the ASUSTek dongle. But that's enough for now. -- To unsubscribe, e-mail: opensuse-support+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-support+owner(a)opensuse.org

1 0

Fwd: Re: [opensuse-support] maven
by Christian Boltz 04 May '19

04 May '19

Hello, Fridrich answered to me and the mailinglist, but it looks like his mail didn't make it to the mailinglist. Therefore I'm forwarding it. My understanding of his mail is that the best solution is zypper rm apache-commons-parent because the package is now only needed at build time. ---------- Forwarded message ---------- Betreff: Re: [opensuse-support] maven Datum: Freitag, 3. Mai 2019, 22:49:33 CEST Von: Fridrich Strba <fridrich.strba AT suse DOT com> An: Christian Boltz <...>, opensuse-support(a)opensuse.org, Fridrich Strba <fstrba AT suse DOT com> Hello, TLDR; version: It was needed only for satisfying formal dependencies, and now it is not needed any more for any java package as runtime dependency. This changes that just landed last week are meant to make that package useful for maven build. On 03/05/2019 19:01, Christian Boltz wrote: > I also noticed this - maven etc. (a total of 123 additional packages [1]) > get dragged in by the latest apache-commons-parent package. > > Therefore a temporary workaround is > zypper al apache-commons-parent > to keep the old package version with less dependencies or > zypper rm apache-commons-parent > to uninstall it. Now, the parent pom files are only useful for maven builds. They provide information about needed plug-ins and build variables for their children projects. They are completely useless on runtime. Nevertheless, when we package a maven artifact using the dependency free %add_maven_depmap macro, the resulting metadata is not standalone and when using such a package, maven must resolve its pom file with all its dependencies and parent pom structure. When integrating maven into openSUSE, I came with better way of handling such packages. I simply remove from the pom file the parent information and leave the runtime dependencies only. There is even a macro for that in javapackages-local (%pom_remove_parent) This allows us to have a proper dependency information in the parent poms since they will not be used for anything else then for building using maven. Before, I had to patch out their dependency information, since they normally require maven plug-ins that were not packaged. > https://build.opensuse.org/package/revisions/openSUSE:Factory/apache-common… > looks like https://build.opensuse.org/request/show/691849 introduced the > additional dependencies. > > Fridrich, are these additional dependencies intentional? Yes, they are intentional because they allow us to use this particular parent package in maven builds. Nonetheless, the parent package should not be needed at runtime by anything. If it is not so, I should be punched and kicked to fixing that ASAP. > I also wonder why I have apache-commons-parent installed. > /var/log/zypp/history says it was installed as part of a zypper dup on > 2019-03-11, but rpm -q --whatrequires and --whatrecommends don't show > anything. At a certain moment of time, this package was needed by a majority of apache-commons-* packages. All the maven plugin dependencies were patched out of it and it was only used to satisfy formal dependency. Now, it is not needed by those packages. So, I stop patching out the dependencies and this package is useful for maven builds of apache-commons-* packages that we build with maven. Cheers Fridrich ------------------------------------------------------------- Regards, Christian Boltz -- <jjohansen> this change is inconsistent with what we do now <jjohansen> however what we do now is broken [from #apparmor] -- To unsubscribe, e-mail: opensuse-support+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-support+owner(a)opensuse.org

1 0

[opensuse-support] maven
by mike 04 May '19

04 May '19

Hi, Just curious, what are all these maven files showing for a tumbleweed zypper dup?? I am not a programmer and do not see any ANT on my system. Iam using a 500GB ssd and do not want to fill it with things I will not use. If I don't need them how would I prevent them from showing on my "zypper dup" ? Thanks........mike -- To unsubscribe, e-mail: opensuse-support+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-support+owner(a)opensuse.org

3 3

[opensuse-support] tw update leaves smb failing
by Patrick Shanahan 01 May '19

01 May '19

20190428 tumbleweed update and subsequent reboot leaves me w/o samba access to windows machines (primarily for backup purposes) and no cifs systemctl start smb Crash systemd[1]: Starting Samba SMB Daemon... May 01 08:22:10 Crash smbd[23147]: [2019/05/01 08:22:10.228654, 0] ../../source3/auth/auth_util.c:1386(make_new_session_info_guest) May 01 08:22:10 Crash smbd[23147]: create_local_token failed: NT_STATUS_NO_MEMORY May 01 08:22:10 Crash smbd[23147]: [2019/05/01 08:22:10.228791, 0] ../../source3/smbd/server.c:2041(main) May 01 08:22:10 Crash smbd[23147]: ERROR: failed to setup guest info. May 01 08:22:10 Crash systemd[1]: smb.service: Main process exited, code=exited, status=255/EXCEPTION May 01 08:22:10 Crash systemd[1]: smb.service: Failed with result 'exit-code'. May 01 08:22:10 Crash systemd[1]: Failed to start Samba SMB Daemon. # smb.conf is the main Samba configuration file. You find a full commented # version at /usr/share/doc/packages/samba/examples/smb.conf.SUSE if the # samba-doc package is installed. /etc/samba/smb.conf: [global] passdb backend = tdbsam printing = cups printcap name = cups printcap cache time = 750 cups options = raw map to guest = Bad User logon path = \\%L\profiles\.msprofile logon home = \\%L\%U\.9xprofile logon drive = P: usershare allow guests = No security = domain usershare max shares = 100 wins support = No wins server = [homes] comment = Home Directories valid users = %S, %D%w%S browseable = No read only = No inherit acls = Yes [profiles] comment = Network Profiles Service path = %H read only = No store dos attributes = Yes create mask = 0600 directory mask = 0700 [users] comment = All users path = /home read only = No inherit acls = Yes veto files = /aquota.user/groups/shares/ [groups] comment = All groups path = /home/groups read only = No inherit acls = Yes [printers] comment = All Printers path = /var/tmp printable = Yes create mask = 0600 browseable = No [print$] comment = Printer Drivers path = /var/lib/samba/drivers write list = @ntadmin root force group = ntadmin create mask = 0664 directory mask = 0775 I have found recent (~1 year) mention of NT_STATUS_NO_MEMORY, but none appear to apply to my status and until yesterdays update, my system worked fine. my local server on 42.2 appears to have developed the same or similar problem yesterday, no cifs access but samba is running, so may be something changed on windows 10. unadvertised as usual. the reverse is not true. the windows machine has directory access to my 42.2 server. tks, -- (paka)Patrick Shanahan Plainfield, Indiana, USA @ptilopteri http://en.opensuse.org openSUSE Community Member facebook/ptilopteri Registered Linux User #207535 @ http://linuxcounter.net Photos: http://wahoo.no-ip.org/piwigo paka @ IRCnet freenode -- To unsubscribe, e-mail: opensuse-support+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse-support+owner(a)opensuse.org

1 2