Hi, ich möchte meine Digitalkamera Minolta Dimage S404 mit Linux auslesen. Ich habe schon die HOWTO gelesen und die mailing-Liste durchsucht. Zwar haben einige wohl das gleiche Problem, jedoch finde ich keine Lösung. Was dort steht, funktioniert einfach nicht. Ich verwende SuSE 8.0. Die Meldung, die ich erhalte, hängt hinten dran. Beim mounten bekomme ich folgende Fehlermeldung: # mount -t vfat /dev/sda1 /media/kamera/ mount: /dev/sda1 ist kein gültiges blockorientiertes Gerät In der /etc/fstab existieren die Zeilen: /dev/sda1 /media/kamera vfat rw,auto,user,exec 0 0 usbdevfs /proc/bus/usb usbdevfs noauto 0 0 Vielen Dank für die Hilfe Gruß Heiko Meldung aus dmesg: hub.c: USB new device connect on bus1/1, assigned device number 6 usb-uhci.c: interrupt, status 3, frame# 598 WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 6 VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sd(8,0) usb.c: USB disconnect on device 6 sda : READ CAPACITY failed. sda : status = 1, message = 00, host = 0, driver = 08 Info fld=0xa00 (nonstd), Current sd00:00: sns = 70 2 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 sda : block size assumed to be 512 bytes, disk size 1GB. sda: test WP failed, assume Write Enabled sda: I/O error: dev 08:00, sector 0 I/O error: dev 08:00, sector 0 unable to read partition table Device not ready. Make sure there is a disc in the drive. I/O error: dev 08:00, sector 0 Device not ready. Make sure there is a disc in the drive. VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,1) Device not ready. Make sure there is a disc in the drive. VFS: Disk change detected on device sd(8,0) sda : READ CAPACITY failed. sda : status = 1, message = 00, host = 0, driver = 08 Info fld=0xa00 (nonstd), Current sd00:00: sns = 70 2 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 sda : block size assumed to be 512 bytes, disk size 1GB. sda: I/O error: dev 08:00, sector 0 I/O error: dev 08:00, sector 0 unable to read partition table Device not ready. Make sure there is a disc in the drive. I/O error: dev 08:00, sector 0 Device not ready. Make sure there is a disc in the drive. hub.c: USB new device connect on bus1/1, assigned device number 7 usb-uhci.c: interrupt, status 3, frame# 1587 WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 7 VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,1) usb.c: USB disconnect on device 7 VFS: Disk change detected on device sd(8,0) sda : READ CAPACITY failed. sda : status = 1, message = 00, host = 0, driver = 08 Info fld=0xa00 (nonstd), Current sd00:00: sns = 70 2 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 sda : block size assumed to be 512 bytes, disk size 1GB. sda: test WP failed, assume Write Enabled sda: I/O error: dev 08:00, sector 0 I/O error: dev 08:00, sector 0 unable to read partition table Device not ready. Make sure there is a disc in the drive. I/O error: dev 08:00, sector 0 Device not ready. Make sure there is a disc in the drive. VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,0) VFS: Disk change detected on device sr(11,1) VFS: Disk change detected on device sr(11,1) Device not ready. Make sure there is a disc in the drive. VFS: Disk change detected on device sd(8,0) sda : READ CAPACITY failed. sda : status = 1, message = 00, host = 0, driver = 08 Info fld=0xa00 (nonstd), Current sd00:00: sns = 70 2 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 sda : block size assumed to be 512 bytes, disk size 1GB. sda: I/O error: dev 08:00, sector 0 I/O error: dev 08:00, sector 0 unable to read partition table Device not ready. Make sure there is a disc in the drive. I/O error: dev 08:00, sector 0 Device not ready. Make sure there is a disc in the drive.