Thanks for the reply, here is the info which you have requested: (I know, the machine has a strange name.....) 1. I installed Suse 8.2, then I updated the kernel from the use site, but now I am using the mantel kernel version: 2.4.21-4-athlon, I tried to compile the 2.5 and 2.6 kernels, but no success so far :-( note, right now the temperature in th cpu is: # cat /proc/acpi/thermal_zone/THRM/temperature temperature: 66 C and the load is (from uptime): 2:10pm up 0:43, 7 users, load average: 1.45, 1.49, 1.34 2. >> cat /proc/acpi/processor/CPU0/info processor id: 0 acpi id: 0 bus mastering control: yes power management: yes throttling control: no performance management: no limit interface: no 3. cat /proc/acpi/processor/CPU0/throttling gives simply: <not supported> 4. # grep -i ACPI /var/log/boot.msg <4> BIOS-e820: 000000000bef0000 - 000000000beff000 (ACPI data) <4> BIOS-e820: 000000000beff000 - 000000000bf00000 (ACPI NVS) <7>ACPI: have wakeup address 0xc0001000 <6>ACPI: RSDP (v000 PTLTD ) @ 0x000f7450 <6>ACPI: RSDT (v001 PTLTD RSDT 01540.00000) @ 0x0bef8bf5 <6>ACPI: FADT (v001 ATI Raptor 01540.00000) @ 0x0befee2b <6>ACPI: BOOT (v001 PTLTD $SBFTBL$ 01540.00000) @ 0x0befee9f <6>ACPI: SSDT (v001 PTLTD POWERNOW 01540.00000) @ 0x0befeec7 <6>ACPI: DSDT (v001 ATI U1_M1535 01540.00000) @ 0x00000000 <5>ACPI: BIOS passes blacklist <6>ACPI: Subsystem revision 20030522 <6>ACPI: Interpreter enabled <6>ACPI: Using PIC for interrupt routing <6>ACPI: System [ACPI] (supports S0 S3 S4 S5) <6>ACPI: PCI Root Bridge [PCI0] (00:00) <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] <4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 *10) <4>ACPI: PCI Interrupt Link [LNKB] (IRQs 7 *11) <4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 10, enabled at IRQ 9) <4>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 10, disabled) <4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 10, disabled) <4>ACPI: PCI Interrupt Link [LNKF] (IRQs 7 *11) <4>ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 6 10) <4>ACPI: PCI Interrupt Link [LNKH] (IRQs *5 7) <4>ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 6 10, enabled at IRQ 9) <6>ACPI: Embedded Controller [EC0] (gpe 24) <4>ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 <4>ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10 <6>PCI: Using ACPI for IRQ routing <6>PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' <notice>/etc/init.d/rc5.d/S14acpid start Loading ACPI modules (ac fan processor battery thermal button ) Starting acpid <notice>startproc: execve (/usr/sbin/acpid) [ /usr/sbin/acpid ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=26 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=118 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin vga=0x317 RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=38 HOME=/ SHLVL=2 splash=silent sscripts=39 _=/sbin/startproc DAEMON=/usr/sbin/acpid ] <notice>'/etc/init.d/rc5.d/S14acpid start' exits with status 0 5. grep -i ACPI /var/log/messages|grep Aug Aug 1 08:02:50 pcgf83-l3 kernel: ACPI: AC Adapter [ACAD] (off-line) Aug 1 08:02:50 pcgf83-l3 kernel: ACPI: Processor [CPU0] (supports C1 C2) Aug 1 08:02:50 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: init_module: No such device Aug 1 08:02:50 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: insmod /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o failed Aug 1 08:02:50 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: insmod toshiba_acpi failed Aug 1 08:02:50 pcgf83-l3 kernel: ACPI: Battery Slot [BAT1] (battery present) Aug 1 08:02:50 pcgf83-l3 kernel: ACPI: Thermal Zone [THRM] (37 C) Aug 1 08:02:50 pcgf83-l3 kernel: ACPI: Power Button (FF) [PWRF] Aug 1 08:02:50 pcgf83-l3 kernel: ACPI: Lid Switch [LID] Aug 1 09:46:54 pcgf83-l3 kernel: ACPI: AC Adapter [ACAD] (on-line) Aug 1 09:46:54 pcgf83-l3 kernel: ACPI: Processor [CPU0] (supports C1 C2) Aug 1 09:46:54 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: init_module: No such device Aug 1 09:46:54 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: insmod /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o failed Aug 1 09:46:54 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: insmod toshiba_acpi failed Aug 1 09:46:54 pcgf83-l3 kernel: ACPI: Battery Slot [BAT1] (battery present) Aug 1 09:46:54 pcgf83-l3 kernel: ACPI: Thermal Zone [THRM] (46 C) Aug 1 09:46:54 pcgf83-l3 kernel: ACPI: Power Button (FF) [PWRF] Aug 1 09:46:54 pcgf83-l3 kernel: ACPI: Lid Switch [LID] Aug 1 09:52:43 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: init_module: No such device Aug 1 09:52:43 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: insmod /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o failed Aug 1 09:52:43 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: insmod toshiba_acpi failed Aug 1 13:26:58 pcgf83-l3 kernel: ACPI: AC Adapter [ACAD] (on-line) Aug 1 13:26:58 pcgf83-l3 kernel: ACPI: Processor [CPU0] (supports C1 C2) Aug 1 13:26:58 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: init_module: No such device Aug 1 13:26:58 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: insmod /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o failed Aug 1 13:26:58 pcgf83-l3 insmod: /lib/modules/2.4.21-4-athlon/kernel/drivers/acpi/toshiba_acpi.o: insmod toshiba_acpi failed Aug 1 13:26:58 pcgf83-l3 kernel: ACPI: Battery Slot [BAT1] (battery present) Aug 1 13:26:58 pcgf83-l3 kernel: ACPI: Thermal Zone [THRM] (52 C) Aug 1 13:26:58 pcgf83-l3 kernel: ACPI: Power Button (FF) [PWRF] Aug 1 13:26:58 pcgf83-l3 kernel: ACPI: Lid Switch [LID] pcgf83-l3:/home/has # 6. finally, the full dmesg is attached. Thank You Very Much! Adam Heiner Kuhlmann wrote:
Am Freitag, 1. August 2003 10:00 schrieb Adham Hashibon:
Danke! aber es geht nichts... I hasve acpid up and running, but, even after doing the two steps you mentiond I gert the following:
# cat /proc/acpi/processor/CPU0/throttling <not supported>
Which SuSE and which kernel you are using?
Does your acpi come up: 1. exists the directory /proc/acpi 2. what is with /proc/acpi/processor/CPU0/info 3. and cat /proc/acpi/processor/CPU0/throttling
4. What is with grep -i ACPI /var/log/boot.msg grep -i ACPI /var/log/messages
Heiner
Linux version 2.4.21-4-athlon (root@Athlon.suse.de) (gcc version 3.3 (SuSE Linux)) #1 Fri Jul 4 11:17:40 UTC 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bef0000 (usable)
BIOS-e820: 000000000bef0000 - 000000000beff000 (ACPI data)
BIOS-e820: 000000000beff000 - 000000000bf00000 (ACPI NVS)
BIOS-e820: 000000000bf00000 - 000000000c000000 (reserved)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
822MB vmalloc/ioremap area available.
0MB HIGHMEM available.
190MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 48880
zone(0): 4096 pages.
zone(1): 44784 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7450
ACPI: RSDT (v001 PTLTD RSDT 01540.00000) @ 0x0bef8bf5
ACPI: FADT (v001 ATI Raptor 01540.00000) @ 0x0befee2b
ACPI: BOOT (v001 PTLTD $SBFTBL$ 01540.00000) @ 0x0befee9f
ACPI: SSDT (v001 PTLTD POWERNOW 01540.00000) @ 0x0befeec7
ACPI: DSDT (v001 ATI U1_M1535 01540.00000) @ 0x00000000
ACPI: BIOS passes blacklist
Building zonelist for node : 0
Kernel command line: root=/dev/hda2 vga=0x317 hdc=ide-scsi hdclun=0 splash=silent splash=silent
ide_setup: hdc=ide-scsi
ide_setup: hdclun=0
bootsplash: silent mode.
bootsplash: silent mode.
Initializing CPU#0
Detected 1656.408 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3303.01 BogoMIPS
Memory: 189184k/195520k available (1791k kernel code, 5948k reserved, 595k data, 176k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383f9ff c1cbf9ff 00000000 00000000
CPU: Common caps: 0383f9ff c1cbf9ff 00000000 00000000
CPU: AMD mobile AMD Athlon(tm) XP2000+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030522
PCI: PCI BIOS revision 2.10 entry at 0xfd87b, last bus=3
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs 7 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 10, enabled at IRQ 9)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 10, disabled)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 10, disabled)
ACPI: PCI Interrupt Link [LNKF] (IRQs 7 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 6 10)
ACPI: PCI Interrupt Link [LNKH] (IRQs *5 7)
ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 6 10, enabled at IRQ 9)
ACPI: Embedded Controller [EC0] (gpe 24)
schedule_task(): keventd has not started
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
PCI: No IRQ known for interrupt pin A of device 00:10.0
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd
bigpage subsystem: allocated 0 bigpages (=0MB).
kinoded started
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 12220
aio_setup: sizeof(struct page) = 48
vesafb: framebuffer at 0xe0000000, mapped to 0xcc81b000, size 12288k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:51a9
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture.... silenjpeg size 30311 bytes, found (1024x768, 23130 bytes, v3).
Got silent jpeg.
Got silent jpeg.
Console: switching to colour frame buffer device 118x38
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (10b9,5457,103c,0024)
and the manufacturer and name of serial board or modem board
to serial-pci-info@lists.sourceforge.net.
register_serial(): autoconfig failed
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 16 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Warning: ATI Radeon IGP Northbridge is not yet fully tested.
ALI15X3: IDE controller at PCI slot 00:10.0
PCI: No IRQ known for interrupt pin A of device 00:10.0
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8080-0x8087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x8088-0x808f, BIOS settings: hdc:pio, hdd:pio
hda: HITACHI_DK23EA-20, ATA DISK drive
blk: queue c03f3300, I/O limit 4095Mb (mask 0xffffffff)
hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4240N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 39070080 sectors (20004 MB) w/2048KiB Cache, CHS=2432/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3 hda4
ide-floppy driver 0.99.newide
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 480k freed
VFS: Mounted root (ext2 filesystem).
reiserfs: found format "3.6" with standard journal
reiserfs: enabling write barrier flush mode
reiserfs: using ordered data mode
reiserfs: checking transaction log (device ide0(3,2)) ...
for (ide0(3,2))
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 176k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
reiserfs: enabling write barrier flush mode
LVM version 1.0.5+(mp-v6a)(22/07/2002) module loaded
reiserfs: enabling write barrier flush mode
Adding Swap: 530104k swap-space (priority 42)
reiserfs: enabling write barrier flush mode
reiserfs: enabling write barrier flush mode
MSDOS FS: IO charset iso8859-1
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: RW/DVD GCC-4240N Rev: 0111
Type: CD-ROM ANSI SCSI revision: 02
powernow: AMD K7 CPU detected.
powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
powernow: Found PSB header at c00f17f0
powernow: Table version: 0x12
powernow: Flags: 0x0 (Mobile voltage regulator)
powernow: Settling Time: 100 microseconds.
powernow: Has 14 PST tables. (Only dumping ones relevant to this CPU).
powernow: PST:11 (@c00f18c8)
powernow: cpuid: 0x781 fsb: 133 maxFID: 0x3 startvid: 0xb
powernow: FID: 0x12 (4.0x [532MHz]) VID: 0x13 (1.200V)
powernow: FID: 0x4 (5.0x [665MHz]) VID: 0x13 (1.200V)
powernow: FID: 0x6 (6.0x [798MHz]) VID: 0x13 (1.200V)
powernow: FID: 0xa (8.0x [1064MHz]) VID: 0x11 (1.250V)
powernow: FID: 0xe (10.0x [1330MHz]) VID: 0xd (1.350V)
powernow: FID: 0x3 (12.5x [1662MHz]) VID: 0xb (1.450V)
powernow: Minimum speed 532 MHz. Maximum speed 1662 MHz.
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker