Hallo, auch den vierten Abend halte ich wacker durch, irgendwie will ich´s jetzt auch wissen. Ich habe gestern einen Call bei AVM aufgemacht, die haben mir geraten erst mal drdsl auszuführen. drdsl gibt folgendes aus: linux:~ # drdsl DSL Assistant version 1.0.3 copyright AVM 2002 The DSL Assistant is examining your DSL configuration... The DSL-Controller has the number 1. Searching for remote vendor ID... (This could take over a minute) Segmentation fault Was kann ich mir unter Segmentation fault vorstellen ? Ist das ein Arbeitsspeicher Segment ?` Dann sagt AVM weiter, ich sollte an einer Konsole pppd call t-dsl eingeben, das sagt folgendes: Plugin userpass.so loaded. userpass: $Revision: 1.5 $ Plugin capiplugin.so loaded. capiplugin: $Revision: 1.35 $ capiconn: 1.9 capiplugin: phase serialconn. loading adsl parameters from /etc/drdsl/adsl.conf ... capiplugin: contr=1 controller 1: listen_change_state 0 -> 1 contr 1: listenconf Info=0x0000 (No additional information) infomask=0x144 cipmask=0x0 capimask2=0x0 controller 1: listen_change_state 1 -> 0 plci_change_state:0x0 0 -> 1 event=1 capiplugin: leased line (adslpppoe) plci_change_state:0x101 1 -> 2 event=3 plci_change_state:0x101 2 -> 3 event=6 ncci_change_state:0x101 0 -> 1 event=1 ncci_change_state:0x10101 1 -> 3 event=3 ncci_change_state:0x10101 3 -> 7 event=10 ncci_change_state:0x10101 7 -> 0 event=13 plci_change_state:0x101 3 -> 7 event=8 plci_change_state:0x101 7 -> 8 event=9 plci_change_state:0x101 8 -> 0 event=11 capiplugin: disconnect(remote): "" -> "" outgoing (pcli=0x101/ncci=0x10101) 0x0000 (0x3312) - No additional information plci_change_state:0x0 0 -> 1 event=1 capiplugin: leased line (adslpppoe) plci_change_state:0x101 1 -> 2 event=3 plci_change_state:0x101 2 -> 3 event=6 ncci_change_state:0x101 0 -> 1 event=1 ncci_change_state:0x10101 1 -> 3 event=3 ncci_change_state:0x10101 3 -> 7 event=10 ncci_change_state:0x10101 7 -> 0 event=13 plci_change_state:0x101 3 -> 7 event=8 plci_change_state:0x101 7 -> 8 event=9 plci_change_state:0x101 8 -> 0 event=11 capiplugin: disconnect(remote): "" -> "" outgoing (pcli=0x101/ncci=0x10101) 0x0000 (0x3312) - No additional information plci_change_state:0x0 0 -> 1 event=1 capiplugin: leased line (adslpppoe) plci_change_state:0x101 1 -> 2 event=3 plci_change_state:0x101 2 -> 3 event=6 ncci_change_state:0x101 0 -> 1 event=1 ncci_change_state:0x10101 1 -> 3 event=3 ncci_change_state:0x10101 3 -> 7 event=10 ncci_change_state:0x10101 7 -> 0 event=13 plci_change_state:0x101 3 -> 7 event=8 plci_change_state:0x101 7 -> 8 event=9 plci_change_state:0x101 8 -> 0 event=11 capiplugin: disconnect(remote): "" -> "" outgoing (pcli=0x101/ncci=0x10101) 0x0000 (0x3312) - No additional information plci_change_state:0x0 0 -> 1 event=1 capiplugin: leased line (adslpppoe) plci_change_state:0x101 1 -> 2 event=3 plci_change_state:0x101 2 -> 3 event=6 ncci_change_state:0x101 0 -> 1 event=1 ncci_change_state:0x10101 1 -> 3 event=3 ncci_change_state:0x10101 3 -> 7 event=10 ncci_change_state:0x10101 7 -> 0 event=13 plci_change_state:0x101 3 -> 7 event=8 plci_change_state:0x101 7 -> 8 event=9 plci_change_state:0x101 8 -> 0 event=11 capiplugin: disconnect(remote): "" -> "" outgoing (pcli=0x101/ncci=0x10101) 0x0000 (0x3312) - No additional information capiplugin: couldn't make connection controller 1: listen_change_state 0 -> 1 contr 1: listenconf Info=0x0000 (No additional information) infomask=0x144 cipmask=0x0 capimask2=0x0 controller 1: listen_change_state 1 -> 0 capiplugin: exit
1. boot option pci=noacpi 2. boot option noacpi 3. boot option apic
Alle Bootoptionen habe ich auch schon durch. Kann vielleicht jemand was entdecken ?