Hier ist die AVM 2 mal eingetragen, loesche mal den 2. Eintrag.
Was steht denn in /etc/rc.config.d/i4l_hardware.rc.config ?
Hier steht folgendes: # # driver-id for card identification # set to "HiSax" # or whatever you defined when loading driver within kernel # I4L_ID_1="avm"
# # D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) 3=leased 4=NI1 # I4L_PROTOCOL_1="2"
# Type ISDN-card # HiSax passiv type 1...7999 (used 37) # AVM active type 8001 # Eicon active type 8010 # IBM active type 8020 # ICN active type 8030 I4L_TYPE_1="8001"
# # Subtype of a given type # I4L_SUBTYPE_1="1"
# # used IRQ if any # eg. 12 or 15 when loading as module # set to "" when driver is loaded within kernel # I4L_IRQ_1=""
# # Membase if any # I4L_MEMBASE_1=""
# # IO address if any # I4L_IO_1=""
# # IO0 (ISA PnP) # I4L_IO0_1=""
# # IO1 (ISA PnP) # I4L_IO1_1=""
# # IO2 (ISA PnP) # I4L_IO2_1=""
# # for backward compatibility # HiSax-modul: the complete line to load module # e.g Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and # ELSA QuickStep1000 PCI, Euro ISDN: # "type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa" # # is equivalent for follow commandline # modprobe hisax type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa # I4L_MODUL_OPTIONS_1=""
# # specials # # Debug Level, 4 (default) # I4L_HISAXDEBUG_1=""
# # EAZ mapping set # eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" # I4L_EAZMAP_1=""
Ab hier loeschen:
I4L_ID_2="avm2" I4L_PROTOCOL_2="2" I4L_TYPE_2="8001" I4L_SUBTYPE_2="1" I4L_IRQ_2="" I4L_MEMBASE_2="0x0" I4L_IO_2="0x0" I4L_IO0_2="0x0" I4L_IO1_2="0x0" I4L_IO2_2="0x0" I4L_MODUL_OPTIONS_2="" I4L_HISAXDEBUG_2="" I4L_EAZMAP_2=""
Erstmal nur eine B1 configurieren und die Fritz weglassen (kann im Rechner bleiben). System neustarten. Sicherstellen, das die B1 auch am S0 haengt.
Neben der B1 habe ich noch eine FritzCard PCI im Rechner. Diese funktioniert problemlos. Die B1 wird von Yast1 und Yast2 erkannt. Unter Yast1 krieg ich auch keine Fehlermeldung beim konfigurieren/ starten. Die B1 müsste also funktionieren. Mit lsmod stellte ich fest, das auch die Module für capi und für die b1 geladen wurden. S0 -Was ist das? Es funktioniert leider immer noch nicht. Bei einem erneuten Versuch, krieg ich folgende Meldungen in der /var/log/messages:
Jul 4 20:12:00 linux last message repeated 6 times Jul 4 20:12:02 linux kernel: ippp0: dialing 1 0192071... Jul 4 20:12:09 linux kernel: isdn: HiSax,ch0 cause: E001B Jul 4 20:12:11 linux kernel: isdn_net: local hangup ippp0 Jul 4 20:12:11 linux kernel: ippp0: Chargesum is 0 Jul 4 20:12:18 linux kernel: ippp2: dialing 1 07118949099... Jul 4 20:12:25 linux kernel: isdn: HiSax,ch0 cause: E001B Jul 4 20:12:26 linux kernel: isdn_net: local hangup ippp2 Jul 4 20:12:26 linux kernel: ippp2: Chargesum is 0 Jul 4 20:12:29 linux kernel: NETDEV WATCHDOG: ippp0: transmit timed out Jul 4 20:12:29 linux kernel: isdn_tx_timeout dev ippp0 dialstate 0 Jul 4 20:12:29 linux kernel: isdn_net: ippp0: dial rejected: interface not in dialmode `auto', signalling dst_link_failure Hier ist mal ein Auszug aus der /var/log/boot: <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <5>ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 <6>dss1_divert module successfully installed <6>HiSax: Linux Driver for passive ISDN cards <6>HiSax: Version 3.5 (kernel) <6>HiSax: Layer1 Revision 1.1.4.1 <6>HiSax: Layer2 Revision 1.1.4.1 <6>HiSax: TeiMgr Revision 1.1.4.1 <6>HiSax: Layer3 Revision 1.1.4.1 <6>HiSax: LinkLayer Revision 1.1.4.1 <6>HiSax: Approval certification valid <6>HiSax: Approved with ELSA Microlink PCI cards <6>HiSax: Approved with Eicon Technology Diva 2.01 PCI cards <6>HiSax: Approved with Sedlbauer Speedfax + cards <6>HiSax: Approved with HFC-S PCI A based cards <7>HiSax: Total 1 card defined <6>HiSax: Card 1 Protocol EDSS1 Id=HiSax (0) <6>HiSax: AVM PCI driver Rev. 1.1.4.1 <6>AVM PCI: stat 0x3020a <6>AVM PCI: Class A Rev 2 <6>HiSax: AVM Fritz!PCI config irq:10 base:0xCC00 <6>AVM PCI: ISAC version (0): 2086/2186 V1.1 <6>AVM Fritz PnP/PCI: IRQ 10 count 0 <6>AVM Fritz PnP/PCI: IRQ 10 count 3 <6>HiSax: DSS1 Rev. 1.1.4.1 <6>HiSax: 2 channels added <6>HiSax: MAX_WAITING_CALLS added <5>isdnloop-ISDN-driver Rev 1.1.4.1 <6>NET4: Linux TCP/IP 1.0 for NET4.0 <6>IP Protocols: ICMP, UDP, TCP, IGMP <6>IP: routing cache hash table of 2048 buckets, 16Kbytes <6>TCP: Hash tables configured (established 16384 bind 16384) <6>Linux IP multicast router 0.06 plus PIM-SM <6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. <5>RAMDISK: Compressed image found at block 0 <6>Freeing initrd memory: 666k freed Mir ist gerade noch etwas aufgefallen. Bei ippp0 habe ich die B1 als Hardware angegeben (mit yast1). Wenn ich aber einfach das Kabel von der B1 in die FritzCard umstecke, dann komme ich sofort ins Internet! Also muss da irgendwo schon der Fehler legen. Hoffentlich kannst Du damit etwas anfangen. Gruß, Jürgen