Hallo zusammen... ich versuche eine erstmalige Inbetriebnahme einer Eicon SCOM ISA Bus Karte... SUSE 7.3 Ein Teil der Installation scheint schon OK zu sein, jedoch wird die Firmware der Karte nicht geladen. Ich hoffe die Karte ict noch nicht zu alt, um noch Hilfe zu bekommen. Hier noch eine Config und die Boot messages: linux:/etc/init.d # cat /etc/rc.config.d/i4l_hardware.rc.config # # driver-id for card identification # set to "HiSax" # or whatever you defined when loading driver within kernel # I4L_ID_1="eicon0" # # D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) 3=leased 4=NI1 # I4L_PROTOCOL_1="2" # Type ISDN-card # HiSax passiv type 1...7999 (used 37) # AVM active type 8001 # Eicon active type 8010 # IBM active type 8020 # ICN active type 8030 I4L_TYPE_1="8010" # # Subtype of a given type # I4L_SUBTYPE_1="2" # # used IRQ if any # eg. 12 or 15 when loading as module # set to "" when driver is loaded within kernel # I4L_IRQ_1="11" # # Membase if any # I4L_MEMBASE_1="0xd0000" # # IO address if any # I4L_IO_1="" # # IO0 (ISA PnP) # I4L_IO0_1="" # # IO1 (ISA PnP) # I4L_IO1_1="" # # IO2 (ISA PnP) # I4L_IO2_1="" # # for backward compatibility # HiSax-modul: the complete line to load module # e.g Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and # ELSA QuickStep1000 PCI, Euro ISDN: # "type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa" # # is equivalent for follow commandline # modprobe hisax type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa # I4L_MODUL_OPTIONS_1="" # # specials # # Debug Level, 4 (default) # I4L_HISAXDEBUG_1="" # # EAZ mapping set # eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" I4L_EAZMAP_1="" linux:/etc/init.d # linux:/etc/init.d # ./i4l_hardware start Loading ISDN drivers ... Loading EICON driver ... /sbin/insmod /lib/modules/2.4.10-4GB/kernel/drivers/net/slhc.o Using /lib/modules/2.4.10-4GB/kernel/drivers/net/slhc.o Symbol version prefix '' /sbin/insmod /lib/modules/2.4.10-4GB/kernel/drivers/isdn/isdn.o Using /lib/modules/2.4.10-4GB/kernel/drivers/isdn/isdn.o /sbin/insmod /lib/modules/2.4.10-4GB/kernel/drivers/isdn/eicon/eicon.o irq=11 membase=0xd0000 id=eicon0 Using /lib/modules/2.4.10-4GB/kernel/drivers/isdn/eicon/eicon.o Loading EICON firmware ... Loading Startup Code (dnload.bin 1024 bytes)... Adapter-type is Eicon-SCOM Protocol File : /usr/lib/isdn/te_etsi.sy (67406 bytes) Downloading Code (67406 bytes)... Error, possibly updated driver, try re-compile utility ! ioctl LOAD: Input/output error Loading of Firmware etsi failed! Check that the values in '/etc/rc.config.d/*' are correct: and see /usr/share/doc/packages/i4l/README.eicon I4L_ID: eicon0 I4L_IRQ: 11 I4L_MEMBASE: 0xd0000 linux:/etc/init.d # -- Nette Leute zum Flirten, Lachen und Verlieben, fuer Reisen, Sport und Freizeit! http://www.freenet.de/tipp/single