Hallo Leute,
ich habe ein kleines Problem mit dem Routing von meinem Linux-Router
zu einem Elsa-Lancom 1100.
Die Routen meiner Meinung nach richtig eingestellt :
Linux :
10.1.1.1 0.0.0.0 255.255.255.255 UH 0 0 0
eth0
10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0
eth0
192.168.5.1 0.0.0.0 255.255.255.255 UH 0 0 0
ippp5
192.168.5.0 0.0.0.0 255.255.255.0 U 0 0 0
ippp5
10.105.0.0 0.0.0.0 255.255.0.0 U 0 0 0
ippp5
oder
...
10.105.0.0 192.168.5.1 255.255.0.0 UG 0 0 0
ippp5
geht beides nicht
LanCom :
BALZER 10.1.0.0 255.255.0.0 (Balzer repräsentiert die
Wähleintragungen)
Das Einwahlprotokoll :
Aug 16 12:33:14 castle ipppd[23027]: rcvd [0][IPCP ConfReq id=0x0 ]
Aug 16 12:33:14 castle kernel: Received CCP frame from peer
Aug 16 12:33:14 castle kernel: [5/3].ccp-rcv[0]: 01 00 00 09 11 05 00 01
03
Aug 16 12:33:14 castle ipppd[23027]: sent [0][IPCP ConfRej id=0x0
]
Aug 16 12:33:14 castle ipppd[23027]: rcvd [0][CCP ConfReq id=0x0 ]
Aug 16 12:33:14 castle ipppd[23027]: sent [0][IPCP ConfReq id=0x2 ]
Aug 16 12:33:14 castle ipppd[23027]: rcvd [0][IPXCP ConfNak id=0x1
]
Aug 16 12:33:14 castle ipppd[23027]: sent [0][IPXCP ConfReq id=0x2
<complete>]
Aug 16 12:33:14 castle ipppd[23027]: rcvd [0][IPXCP ConfReq id=0x2
]
Aug 16 12:33:14 castle ipppd[23027]: sent [0][IPXCP ConfAck id=0x2
]
Aug 16 12:33:14 castle ipppd[23027]: rcvd [0][IPCP ConfReq id=0x2 ]
Aug 16 12:33:14 castle ipppd[23027]: sent [0][IPCP ConfNak id=0x2 ]
Aug 16 12:33:14 castle ipppd[23027]: rcvd [0][IPCP ConfAck id=0x2 ]
Aug 16 12:33:14 castle ipppd[23027]: rcvd [0][IPXCP ConfAck id=0x2
<complete>]
Aug 16 12:33:14 castle ipppd[23027]: rcvd [0][IPCP ConfReq id=0x4 ]
Aug 16 12:33:14 castle ipppd[23027]: sent [0][IPCP ConfAck id=0x4 ]
Aug 16 12:33:14 castle ipppd[23027]: local IP address 192.168.5.1
Aug 16 12:33:14 castle ipppd[23027]: remote IP address 192.168.5.105
Interessanterweise läuft der IPX-Übergang einwandfrei (NWMars)
Ein Ping auf den Lancom (192.168.5.105 und 10.105.1.1) liefert jeweils
die Antwort von der ISDN-Seite des Routers (192.168.5.105)
Die Steuersoftware des Lancom läuft auch über die Verbindung. Nur
nichts IP-basiertes dahinter.
Hat jemand ne Ahnung wo der Fehler zu suchen ist ?
mfg
Ralf Balzer