Mailinglist Archive: opensuse-factory (689 mails)

< Previous Next >
Re: [opensuse-factory] Intel 82574L Gig E Adapter not recognized by kernel 3.8.0-28-desktop
On Sun, Mar 03, 2013 at 09:45:40AM -0800, Bruce Ferrell wrote:
On 03/03/2013 09:08 AM, Roman Bysh wrote:
On 03/03/2013 12:03 PM, Romanator wrote:

<<< snippage >>>

Roman

Please have a look at this link below:

http://www.mjmwired.net/kernel/Documentation/networking/e1000e.txt

That website recommends downloading and updating this driver should
Intel have posted a newer one.

Follow Up

Here's the latest driver update for e1000e posted in Jan/2013.
You'll have to compile it into the kernel.

http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=15817&keyword=e1000e&lang=eng


Cheers!

Roman


Thanks. That won't build against the OpenSUSE 3.8.0-28/29 kernels.
Interestingly enough, I've nor rolled back to 3.4.28-2.20-desktop and ethtool
still says the card's not there:


Did your network card work before? Which distro and kernel version did you use?

modprobe e1000e debug=16

dmesg
[ 2360.580696] e1000e: Intel(R) PRO/1000 Network Driver - 2.2.14-NAPI
[ 2360.580698] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
[ 2360.580721] e1000e 0000:07:00.0: Disabling ASPM L0s L1
[ 2360.580882] e1000e 0000:07:00.0: Interrupt Throttling Rate (ints/sec) set
to dynamic conservative mode
[ 2360.581467] e1000e 0000:07:00.0: irq 59 for MSI/MSI-X
[ 2360.581470] e1000e 0000:07:00.0: irq 60 for MSI/MSI-X
[ 2360.581473] e1000e 0000:07:00.0: irq 61 for MSI/MSI-X
[ 2360.682071] e1000e 0000:07:00.0: eth1: (PCI Express:2.5GT/s:Width x1)
68:05:ca:12:90:dd
[ 2360.682073] e1000e 0000:07:00.0: eth1: Intel(R) PRO/1000 Network Connection
[ 2360.682097] e1000e 0000:07:00.0: eth1: MAC: 4, PHY: 8, PBA No: E46981-008
[ 2360.843419] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 2360.843423] device eth1 entered promiscuous mode


Can you please try another port on target device?



lspci -vv | grep 82574L -A50
07:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network
Connection
Subsystem: Intel Corporation Gigabit CT Desktop Adapter
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7ac0000 (32-bit, non-prefetchable) [disabled]
[size=128K]
Region 1: Memory at f7a00000 (32-bit, non-prefetchable) [disabled]
[size=512K]
Region 2: I/O ports at d000 [disabled] [size=32]
Region 3: Memory at f7ae0000 (32-bit, non-prefetchable) [disabled]
[size=16K]
Expansion ROM at f7a80000 [disabled] [size=256K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 00000000feeff00c Data: 4164
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable- Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap-
ChkEn-
Capabilities: [140 v1] Device Serial Number 68-05-ca-ff-ff-12-90-dd
Kernel driver in use: e1000e

eth1 Link encap:Ethernet HWaddr 68:05:CA:12:90:DD
inet addr:xxx.xxx.xxx.xxx Bcast:xxx.xxx.xxx.xxx
Mask:255.255.255.240
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:16 Memory:f7ac0000-f7ae0000


There is no any packet transfer/receive, did you config ip address manually?

Can you please post your kernel parameter? "cat /proc/cmdline"

Thanks,
David


ethtool eth1
Settings for eth1:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available

--
To unsubscribe, e-mail: opensuse-factory+unsubscribe@xxxxxxxxxxxx
To contact the owner, e-mail: opensuse-factory+owner@xxxxxxxxxxxx

--
To unsubscribe, e-mail: opensuse-factory+unsubscribe@xxxxxxxxxxxx
To contact the owner, e-mail: opensuse-factory+owner@xxxxxxxxxxxx

< Previous Next >