Ok, I have the driver for the card loaded: lsmod | grep e1000e e1000e 252782 0 ./netdriverinfo.sh : 01:00.0 Make/Model = Intel Corporation Gigabit CT Desktop Adapter Ethernet controller = Intel Corporation 82574L Gigabit Network Connection VenID:DevID = 8086:10d3 Driver name = No driver loaded Driver version = No driver loaded Modinfo e1000e as version: 2.1.4-k alias: pci:v00008086d000010D3sv*sd*bc*sc*i* And the Id string seems to be present This worked under 3.7.9 modprobe -r e1000e rr-iii:~ # dmesg [ 3993.357312] e1000e 0000:01:00.0: Disabling ASPM L0s L1 [ 3993.357507] e1000e 0000:01:00.0: irq 59 for MSI/MSI-X [ 3993.357512] e1000e 0000:01:00.0: irq 60 for MSI/MSI-X [ 3993.357519] e1000e 0000:01:00.0: irq 61 for MSI/MSI-X [ 3993.360114] e1000e 0000:01:00.0 eth1: MAC Wakeup cause - Link Status Change [ 3993.430154] device eth1 left promiscuous mode dmesg -C dmesg modprobe e1000e debug=10 rr-iii:~ # dmesg [ 4040.770118] e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k [ 4040.770120] e1000e: Copyright(c) 1999 - 2012 Intel Corporation. [ 4040.770137] e1000e 0000:01:00.0: Disabling ASPM L0s L1 [ 4040.770236] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 4040.770301] e1000e 0000:01:00.0: irq 59 for MSI/MSI-X [ 4040.770305] e1000e 0000:01:00.0: irq 60 for MSI/MSI-X [ 4040.770308] e1000e 0000:01:00.0: irq 61 for MSI/MSI-X [ 4040.867432] e1000e 0000:01:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 68:05:ca:12:90:dd [ 4040.867435] e1000e 0000:01:00.0 eth1: Intel(R) PRO/1000 Network Connection [ 4040.867446] e1000e 0000:01:00.0 eth1: MAC: 3, PHY: 8, PBA No: E46981-008 [ 4041.002738] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 4041.002741] device eth1 entered promiscuous mode modprobe -r e1000e rr-iii:~ # dmesg [ 4040.770118] e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k [ 4040.770120] e1000e: Copyright(c) 1999 - 2012 Intel Corporation. [ 4040.770137] e1000e 0000:01:00.0: Disabling ASPM L0s L1 [ 4040.770236] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 4040.770301] e1000e 0000:01:00.0: irq 59 for MSI/MSI-X [ 4040.770305] e1000e 0000:01:00.0: irq 60 for MSI/MSI-X [ 4040.770308] e1000e 0000:01:00.0: irq 61 for MSI/MSI-X [ 4040.867432] e1000e 0000:01:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 68:05:ca:12:90:dd [ 4040.867435] e1000e 0000:01:00.0 eth1: Intel(R) PRO/1000 Network Connection [ 4040.867446] e1000e 0000:01:00.0 eth1: MAC: 3, PHY: 8, PBA No: E46981-008 [ 4041.002738] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 4041.002741] device eth1 entered promiscuous mode [ 4067.818496] e1000e 0000:01:00.0: Disabling ASPM L0s L1 [ 4067.818693] e1000e 0000:01:00.0: irq 59 for MSI/MSI-X [ 4067.818697] e1000e 0000:01:00.0: irq 60 for MSI/MSI-X [ 4067.818700] e1000e 0000:01:00.0: irq 61 for MSI/MSI-X [ 4067.821318] e1000e 0000:01:00.0 eth1: MAC Wakeup cause - Link Status Change [ 4067.891790] device eth1 left promiscuous mode [ 4067.962423] vboxnetflt: dropped 0 out of 0 packets modprobe e1000e ethtool eth1 Settings for eth1: Cannot get device settings: No such device Cannot get wake-on-lan settings: No such device Cannot get message level: No such device Cannot get link status: No such device No data available Suggestions anyone? I can roll back if needed, but I'd really rather not -- To unsubscribe, e-mail: opensuse-factory+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-factory+owner@opensuse.org