Hola, alguien que sepa manejar smart... el short test me da el siguiente log: ?Alguien sabe qu� quiere decir y si tiene arreglo? smartctl 5.39 2008-10-24 22:33 [i686-suse-linux-gnu] (openSUSE RPM) Copyright (C) 2002-8 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 family Device Model: ST3500630A Serial Number: 9QG06MEN Firmware Version: 3.AAC User Capacity: 500,107,862,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sat Jan 24 21:45:43 2009 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 163) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 110 092 006 Pre-fail Always - 29099634 3 Spin_Up_Time 0x0003 095 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 452 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 084 061 030 Pre-fail Always - 296688016 9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2930 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 456 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 060 048 045 Old_age Always - 40 (Lifetime Min/Max 28/40) 194 Temperature_Celsius 0x0022 040 052 000 Old_age Always - 40 (0 16 0 0) 195 Hardware_ECC_Recovered 0x001a 065 052 000 Old_age Always - 1844796 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 2 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 01 00 00 00 e0 00 00:04:39.592 READ DMA EXT b0 d9 00 00 4f c2 e0 00 00:04:39.559 SMART DISABLE OPERATIONS b0 d2 f1 00 4f c2 e0 00 00:04:39.559 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE b0 d8 00 00 4f c2 e0 00 00:04:38.864 SMART ENABLE OPERATIONS 91 00 3f 00 00 00 ef 00 00:04:35.101 INITIALIZE DEVICE PARAMETERS [OBS-6] Error 1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 01 00 00 00 e0 00 00:00:51.341 READ DMA EXT b0 d9 00 00 4f c2 e0 00 00:00:51.341 SMART DISABLE OPERATIONS b0 d2 f1 00 4f c2 e0 00 00:00:50.641 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE b0 d8 00 00 4f c2 e0 00 00:00:46.867 SMART ENABLE OPERATIONS 91 00 3f 00 00 00 ef 00 00:00:39.156 INITIALIZE DEVICE PARAMETERS [OBS-6] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 2930 - # 2 Short offline Completed without error 00% 2929 - # 3 Short offline Completed without error 00% 2929 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. -- Saludos. C�sar Enfr�ntate a los malos; enfr�ntate a los crueles; enfr�ntate a todos, menos a los tontos. Son demasiados y siempre ser�s derrotado. (Proverbio hind�) -- Para dar de baja la suscripción, mande un mensaje a: opensuse-es+unsubscribe@opensuse.org Para obtener el resto de direcciones-comando, mande un mensaje a: opensuse-es+help@opensuse.org