Bueno aqui os pego el resultado del test, ya me direis si hay algo raro linux-4s66:~ # smartctl -a /dev/hda smartctl version 5.37 [x86_64-suse-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family Device Model: ST380011A Serial Number: 4JV215KV Firmware Version: 8.01 User Capacity: 80,026,361,856 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2 Local Time is: Wed Jan 17 13:00:43 2007 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 58) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 057 053 006 Pre-fail Always - 132883784 3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 4 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 14 7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 125560119 9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5884 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 472 194 Temperature_Celsius 0x0022 038 056 000 Old_age Always - 38 195 Hardware_ECC_Recovered 0x001a 057 053 000 Old_age Always - 132883784 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 40 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 40 occurred at disk power-on lifetime: 5669 hours (236 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 96 39 40 e0 Error: UNC 8 sectors at LBA = 0x00403996 = 4209046 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 96 39 40 e0 00 1d+00:08:33.171 READ DMA EXT e7 00 00 00 00 00 00 00 1d+00:08:33.161 FLUSH CACHE 35 00 08 ee 94 5f e0 00 1d+00:08:33.158 WRITE DMA EXT 25 00 68 71 16 d1 e0 00 1d+00:08:33.158 READ DMA EXT 35 00 10 5e 4b ac e0 00 1d+00:08:33.155 WRITE DMA EXT Error 39 occurred at disk power-on lifetime: 5669 hours (236 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 96 39 40 e0 Error: UNC 8 sectors at LBA = 0x00403996 = 4209046 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 96 39 40 e0 00 1d+00:08:28.750 READ DMA EXT 35 00 08 7e 3a 7c e0 00 1d+00:08:28.747 WRITE DMA EXT 35 00 10 4e 3a 7c e0 00 1d+00:08:28.742 WRITE DMA EXT 35 00 08 2e 3a 7c e0 00 1d+00:08:28.739 WRITE DMA EXT 35 00 08 1e 3a 7c e0 00 1d+00:08:28.727 WRITE DMA EXT Error 38 occurred at disk power-on lifetime: 5646 hours (235 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 96 39 40 e0 Error: UNC 8 sectors at LBA = 0x00403996 = 4209046 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 96 39 40 e0 00 1d+00:32:39.834 READ DMA EXT 25 00 68 c1 f4 db e0 00 1d+00:32:39.824 READ DMA EXT e7 00 00 00 00 00 00 00 1d+00:32:39.815 FLUSH CACHE 35 00 08 36 c7 40 e0 00 1d+00:32:39.800 WRITE DMA EXT e7 00 00 00 00 00 00 00 1d+00:32:39.799 FLUSH CACHE Error 37 occurred at disk power-on lifetime: 5646 hours (235 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 96 39 40 e0 Error: UNC 8 sectors at LBA = 0x00403996 = 4209046 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 96 39 40 e0 00 1d+00:32:39.834 READ DMA EXT 35 00 e8 36 04 df e0 00 1d+00:32:39.824 WRITE DMA EXT 35 00 00 36 00 df e0 00 1d+00:32:39.815 WRITE DMA EXT 35 00 00 36 fc de e0 00 1d+00:32:39.800 WRITE DMA EXT 35 00 00 36 f8 de e0 00 1d+00:32:39.799 WRITE DMA EXT Error 36 occurred at disk power-on lifetime: 5646 hours (235 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 96 39 40 e0 Error: UNC 8 sectors at LBA = 0x00403996 = 4209046 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 96 39 40 e0 00 1d+00:32:34.719 READ DMA EXT 35 00 00 56 b6 de e0 00 1d+00:32:34.710 WRITE DMA EXT 35 00 00 56 b2 de e0 00 1d+00:32:34.699 WRITE DMA EXT 35 00 00 56 ae de e0 00 1d+00:32:34.689 WRITE DMA EXT 35 00 00 56 aa de e0 00 1d+00:32:34.680 WRITE DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 5882 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Gracias por vuestro tiempo Linux 2.6.18.2-34-default x86_64 Usuario actual: nacho@linux-4s66 Sistema: openSUSE 10.2 (X86-64) KDE: 3.5.5 "release 45.2" AMD Athlon 64 Processor 3000+, 1800,11 MHz RAM 1003,00 MB --------------------------------------------------------------------- Para dar de baja la suscripción, mande un mensaje a: opensuse-es+unsubscribe@opensuse.org Para obtener el resto de direcciones-comando, mande un mensaje a: opensuse-es+help@opensuse.org