Manfred Hollstein
On Wed, 08 Jun 2011, 19:06:24 +0200, Andreas Meyer wrote:
Jan Krings
schrieb am Wed, 8 Jun 2011 17:29:32 +0200: Schuss ins Blaue: Was sagt die Festplatte denn selber? smartctl -A /dev/sdX
sdX deine Festplatte. Nicht das die einfach nur kaputt ist und versucht irgendwelche Sektoren zu lesen.
Da hätt ich folgendes:
=== START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0007 252 252 025 Pre-fail Always - 2125 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 77 5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000e 252 252 051 Old_age Always - 0 8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0 9 Power_On_Hours 0x0032 252 252 000 Old_age Always - 80 10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 41 191 G-Sense_Error_Rate 0x0032 083 083 000 Old_age Always - 176178 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 4 194 Temperature_Celsius 0x0022 103 097 000 Old_age Always - 45 (Lifetime Min/Max 20/47) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 252 252 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 38 201 Soft_Read_Error_Rate 0x0032 252 252 000 Old_age Always - 0 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 6 225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 2045
Aua, bei nur 80 Stunden Benutzung wurde die Platte bereits 2045 mal aus und wieder eingeschaltet... Das ist ein "Feature", mit dem die Festplattenhersteller meinen, Strom sparen zu helfen. Dass dabei die Platte permanent aus- und wieder angeht, und damit viel frueher sterben wird, lassen sie dabei auf der Verbraucherseite liegen...
Mach' mal ein
hdparm -B 255 /dev/sda
# hdparm -B 255 /dev/sda /dev/sda: setting Advanced Power Management level to disabled APM_level = off Und wie kann ich es wieder einschalten?
Damit ist dieses "Stromsparfeature" zwar aus, aber die Platte sollte damit auch laenger leben.
Was meint G-Sense_Error_Rate?
Wird bei den Platten vornehmlich fuer transportable Rechner genutzt als Indikator, wie oft du den Rechner schon hast fallen lassen... ;-)
Das ist der Nachteil von diesen miniITX-Gehäusen. Die stehen auf dem Schreibtisch und wenn man mal dranrempelt, bekommt auch der Computer den Stoß ab. Ich log beobachte ich auch folgendes: itx:/home/andreas # tail -f /var/log/messages Jun 8 22:23:32 itx kernel: [ 710.000220] ata1: soft resetting link Jun 8 22:23:32 itx kernel: [ 710.194106] ata1.00: NODEV after polling detection Jun 8 22:23:32 itx kernel: [ 710.194122] ata1.00: revalidation failed (errno=-2) Jun 8 22:23:37 itx kernel: [ 715.151052] ata1: soft resetting link Jun 8 22:23:38 itx kernel: [ 715.396094] ata1.00: NODEV after polling detection Jun 8 22:23:38 itx kernel: [ 715.396110] ata1.00: revalidation failed (errno=-2) Jun 8 22:23:42 itx kernel: [ 720.353056] ata1: soft resetting link Jun 8 22:23:43 itx kernel: [ 720.556367] ata1.00: configured for UDMA/33 Jun 8 22:23:43 itx kernel: [ 720.561396] ata1.01: configured for UDMA/133 Jun 8 22:23:43 itx kernel: [ 720.562971] ata1: EH complete Jun 8 22:24:17 itx kernel: [ 755.000100] ata1.00: limiting speed to PIO4 Jun 8 22:24:17 itx kernel: [ 755.000120] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen Jun 8 22:24:17 itx kernel: [ 755.000133] sr 0:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Jun 8 22:24:17 itx kernel: [ 755.000177] ata1.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Jun 8 22:24:17 itx kernel: [ 755.000182] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout) Jun 8 22:24:17 itx kernel: [ 755.000195] ata1.00: status: { DRDY } Jun 8 22:24:17 itx kernel: [ 755.051059] ata1: soft resetting link Jun 8 22:24:17 itx kernel: [ 755.229077] ata1.00: NODEV after polling detection Jun 8 22:24:17 itx kernel: [ 755.229091] ata1.00: revalidation failed (errno=-2) Jun 8 22:24:22 itx kernel: [ 760.205052] ata1: soft resetting link Jun 8 22:24:23 itx kernel: [ 760.408361] ata1.00: configured for PIO4 Jun 8 22:24:23 itx kernel: [ 760.413223] ata1.01: configured for UDMA/133 Jun 8 22:24:23 itx kernel: [ 760.414792] ata1: EH complete Jun 8 22:24:34 itx kernel: [ 771.358218] ata1.00: qc timeout (cmd 0xa0) Jun 8 22:24:34 itx kernel: [ 771.358248] ata1.00: limiting speed to PIO3 Jun 8 22:24:34 itx kernel: [ 771.358265] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen Jun 8 22:24:34 itx kernel: [ 771.358279] sr 0:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Jun 8 22:24:34 itx kernel: [ 771.358323] ata1.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Jun 8 22:24:34 itx kernel: [ 771.358329] res 51/20:03:00:00:00/00:00:00:00:00/a0 Emask 0x5 (timeout) Jun 8 22:24:34 itx kernel: [ 771.358342] ata1.00: status: { DRDY ERR } Jun 8 22:24:34 itx kernel: [ 771.358368] ata1: soft resetting link Jun 8 22:24:34 itx kernel: [ 771.574358] ata1.00: configured for PIO3 Jun 8 22:24:34 itx kernel: [ 771.579206] ata1.01: configured for UDMA/133 Jun 8 22:24:34 itx kernel: [ 771.583096] ata1: EH complete Jun 8 22:24:39 itx kernel: [ 776.588065] ata1.00: qc timeout (cmd 0xa0) Jun 8 22:24:39 itx kernel: [ 776.588097] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen Ich vermute, dass bedeutet nichts gutes ...
HTH, cheers.
l8er manfred
Andreas -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org