Hallo David Ich hab jetzt mal die Ausgaben von -A und -a angesehen und ich finde das sieht für mich als Laien nicht so gut aus, korrigiere mich bitte. Anbei der Schluss von -a. Wäre nett, wenn Du mich erhellen könntest. Ein -t offline läuft gerade Danke und Gruss Bodo Am Freitag 24 September 2010, 04:37:06 schrieb David Haller:
Oha. Das ist viel. Allerdings kommt's auch darauf an, welche Fehler. Wenn's nur Fehler bzgl. APM z.B. sind (weil die Platte fest eingestellt ist), dann ist das irrelevant, z.B. sowas:
04 51 fe 6c be e8 f0 Error: ABRT
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 05 fe 6c be e8 f0 00 06:48:09.063 SET FEATURES [Enable APM] ec 00 01 00 00 00 f0 00 06:48:09.000 IDENTIFY DEVICE
Bitte hier in der ML nicht die ganze 'smartctl -a' Ausgabe mailen, nur die von '-A' und ggfs. ein beispielhaftes aus -a wie von mir oben.
Error 377 occurred at disk power-on lifetime: 204 hours (8 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 3f 00 00 e0 Error: UNC 8 sectors at LBA = 0x0000003f = 63 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 3f 00 00 e0 0a 00:00:02.666 READ DMA 27 00 00 00 00 00 e0 0a 00:00:02.666 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 0a 00:00:02.666 IDENTIFY DEVICE ef 03 46 00 00 00 a0 0a 00:00:02.666 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 0a 00:00:02.666 READ NATIVE MAX ADDRESS EXT Error 376 occurred at disk power-on lifetime: 204 hours (8 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 3f 00 00 e0 Error: UNC 8 sectors at LBA = 0x0000003f = 63 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 3f 00 00 e0 0a 00:00:02.665 READ DMA 27 00 00 00 00 00 e0 0a 00:00:02.665 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 0a 00:00:02.665 IDENTIFY DEVICE ef 03 46 00 00 00 a0 0a 00:00:02.665 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 0a 00:00:02.665 READ NATIVE MAX ADDRESS EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 205 56 SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1 SMART Selective self-test log data structure revision number 0 Warning: ATA Specification requires selective self-test log data structure revision number = 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed_read_failure [90% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org