Hallo zusammen, ich möchte meine Sony DSC-F828 (BTW: geiles Teil) mit usb-storage als Quasi-Festplatte ansprechen. Leider funktioniert das nicht so ganz. Wenn die Kamera angeschlossen ist, liefert sie folgende Daten: $ cat /proc/bus/usb/devices T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#= 15 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=054c ProdID=0010 Rev= 5.00 S: Manufacturer=Sony S: Product=Sony DSC C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA I: If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=ff Prot=01 Driver=usb-storage E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=255ms $ hwinfo --usb [...] 11: USB 210.0: 10680 Storage Device [Created at usb.100] Unique ID: B3Fu.UiL1CJEqQp4 Hardware Class: unknown Model: "Sony DSC" Hotplug: USB Vendor: usb 0x054c "Sony Corp." Device: usb 0x0010 "DSC-S30/S70/S75/F505V/F505/FD92 Cybershot/Mavica Digital Camera" SubVendor: "Sony" SubDevice: "Sony DSC" Revision: "5.00" USB GUID: 054c00100000000000000000 USB Device status: driver active ("usb-storage") Speed: 1.5 Mbps Config Status: cfg=new, avail=yes, need=no Attached to: #6 (Hub) /var/log/messages: Feb 8 17:28:00 linux kernel: hub.c: new USB device 00:04.2-1.4, assigned address 15 Feb 8 17:28:00 linux kernel: WARNING: USB Mass Storage data integrity not assured Feb 8 17:28:00 linux kernel: USB Mass Storage device found at 15 Feb 8 17:28:03 linux /etc/hotplug/usb.agent[3497]: Can't ignore signal CHLD, forcing to default. Was mir hier fehlt, sind Zeilen wie scsix : SCSI emulation for USB Mass Storage devices Vendor: SONY Model: SONY DSC xxxx Rev: 5.00 Type: Direct-Access ANSI SCSI revision: xx USB Mass Storage support registered. Unter /dev/sd{a|b|c...}1 ist folglich auch nichts zu finden. Damit das Gerät überhaupt als "USB Mass Storage device" erkannt wird, war ein Patch in der Kernel-Source /usr/src/linux/drivers/usb/storage/unusual_devs.h nötig (wohl wg. der Revision-Nr.): /* This entry is needed because the device reports Sub=ff */ UNUSUAL_DEV( 0x054c, 0x0010, 0x0106, 0x0500, "Sony", "DSC-S30/S70/S75/505V/F505/F707/F717/P8", US_SC_SCSI, US_PR_DEVICE, NULL, US_FL_SINGLE_LUN | US_FL_MODE_XLATE ), M.E. kann kein allgemeiner Fehler mit meiner USB-Installation vorliegen: ein anderes Gerät (eine iRiver-Jukebox mit Festplatte) läßt sich einwandfrei einbinden. Die einschlägigen HOWTOs, insb. das für USB-Kameras habe ich gelesen. Irgendwie bin ich jetzt ratlos... Frage: wie kann ich meinem Rechner beibiegen, er möchte doch bitteschön die Kamera als SCSI-Device betrachten? Gruß Rudi -- How much do you want to pay tomorrow?!