ich verwende ein devolo/elsa mircrolink 56k i mit angehängter config - die von Dir angegebenen Einstellungen würden also passen. Vielleicht fällt Dir da noch was auf? rpeipp@gmx.de schrieb:
peter grotz writes:
das Problem kenn ich auch (ohne Lösung) Prozess läuft, das Modem läutet, aber nimmt nicht ab; was nun??
Ist das Modem auch richtig konfiguriert? Wie sieht denn die Datei /var/spool/fax/etc/config.modem aus? Stichwort "ModemType", "ModemFlowControl". Speziell "ModemFlowControl" mußte ich erst immer händisch auf "RTSCTS" stellen. Mit der Standardeinstellung "xonxoff" lief der Empfang bei mir nicht stabil. Der "ModemType" ist aber auch wesentlich. Für ein Elsa MicroLink 33.6TQV habe ich ihn auf "Class2.0" stehen.
Gruß Rainer
gruß -Peter # # HylaFAX Facsimile Software # # Configuration for using the Class 2.0 command interface with # a Elsa MicroLink 56k basic # # CONFIG: CLASS2.0: *ELSA*MicroLink*56k*basic*-RTSCTS # CONFIG: CLASS2.0: *ELSA*MicroLink*56k*basic*-DEFAULT # # BEGIN-SERVER # END-SERVER # # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP # AreaCode: 821 FAXNumber: xxxxxxxxx InternationalPrefix: 0 DialStringRules: etc/dialrules RecvFileMode: 644 LogFileMode: 600 DeviceMode: 666 SpeakerVolume: off GettyArgs: "-r -b -s %s %l" LocalIdentifier: "xxxxxxxxxxx" TagLineFont: etc/lutRS18.pcf TagLineFormat: "_ %%l|%c|Seite %%P von %%T" # ModemType: Class2.0 # use this to supply a hint ModemRate: 115200 # max rate for DCE-DTE communication ModemFlowControl: rtscts # XON/XOFF flow control assumed ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) # # ModemDialCmd: ATDT%s # # ModemResetCmds: ATX3 # stuff to do when modem is reset ModemAnswerCmd: ATA # use this to answer phone ModemNoFlowCmd: AT&K ModemHardFlowCmd: AT&K3 ModemSoftFlowCmd: AT&K1 ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer # # ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" ModemEchoOffCmd: ATE0 # disable command echo ModemVerboseResultsCmd: ATV1 # enable verbose command results ModemResultCodesCmd: ATQ0 # enable result codes ModemOnHookCmd: ATH # place phone on hook (hangup) ModemSoftResetCmd: ATZ # do soft reset of modem ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds ModemRecvFillOrder: LSB2MSB # bit order of received facsimile ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # # Configuration parameters for Class 2.0 modems. # Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0 Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct) Class2CQCmd: "" # commands to enable copy quality proc. Class2AbortCmd: AT+FKS # abort session command Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities Class2TBCCmd: AT+FPP=0 # setup stream mode Class2CRCmd: AT+FCR=1 # enable capability to receive Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing Class2LIDCmd: AT+FLI # set local identifier command Class2DCCCmd: AT+FCC # set modem capabilities command Class2DISCmd: AT+FIS # set session parameters command Class2DDISCmd: "" # disable pre-dial DIS command hack Class2CIGCmd: AT+FPI # set polling identifier command Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command Class2PIECmd: AT+FIE=0 # disable interrupt-enable command Class2PTSCmd: AT+FPS # set post-page status command Class2SPLCmd: AT+FSP # set polling indicator command Class2NFLOCmd: AT+FLO=0 # set no flow control command Class2SFLOCmd: AT+FLO=1 # set software flow control command Class2HFLOCmd: AT+FLO=2 # set hardware flow control command Class2APQueryCmd: none # not supported # $Id: class2,v 1.5 2002/04/07 20:29:25 darren Exp $