Hallo an alle SMP-Brett besitzer mit VIA Chipsen, ich habe ein tyan 230 mit zwei 667 mhz procs. Beim Booten bekomme ich mehrere Meldungen, die Besagen das erstens mit apic nichts ist . Also kein Mapping auf die erweiterten Interrupts. Damit auch kein symmetrisches Processing. Es ist auch egal welche Kernel (2.4.4/2.4.10) ich nehme . Die Meldungen sind die gleichen: <4>Scan SMP from c0000000 for 1024 bytes. <4>Scan SMP from c009fc00 for 1024 bytes. <4>Scan SMP from c00f0000 for 65536 bytes. <4>found SMP MP-table at 000f5610 <4>hm, page 000f5000 reserved twice. <4>hm, page 000f6000 reserved twice. <4>hm, page 000f1000 reserved twice. <4>hm, page 000f2000 reserved twice. <4>On node 0 totalpages: 393200 <4>zone(0): 4096 pages. <4>zone(1): 225280 pages. <4>zone(2): 163824 pages. <4>Intel MultiProcessor Specification v1.4 <4> Virtual Wire compatibility mode. ....................... <4>Bus #0 is PCI <4>Bus #1 is PCI <4>Bus #2 is ISA <4>I/O APIC #2 Version 17 at 0xFEC00000. ............................... <4>Processors: 2 <4>mapped APIC to ffffe000 (fee00000) <4>mapped IOAPIC to ffffd000 (fec00000) .......... <4>POSIX conformance testing by UNIFIX <4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) <4>mtrr: detected mtrr type: Intel <7>CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 <6>CPU: L1 I cache: 16K, L1 D cache: 16K <6>CPU: L2 cache: 256K <6>Intel machine check reporting enabled on CPU#0. ......................... <4>ENABLING IO-APIC IRQs <6>...changing IO-APIC physical APIC ID to 2 ... ok. <4>Synchronizing Arb IDs. <7>init IO_APIC IRQs <7> IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. <6>..TIMER: vector=49 pin1=2 pin2=0 <7>number of MP IRQ sources: 19. <7>number of IO-APIC #2 registers: 24. <6>testing the IO APIC....................... <4> <7>IO APIC #2...... <7>.... register #00: 02000000 <7>....... : physical APIC id: 02 <7>.... register #01: 00178011 <7>....... : max redirection entries: 0017 <7>....... : IO APIC version: 0011 <4> WARNING: unexpected IO-APIC, please mail <4> to linux-smp@vger.kernel.org <7>.... register #02: 00000000 <7>....... : arbitration: 00 <7>.... IRQ redirection table: .............................. <4>cpu: 0, clocks: 1332883, slice: 444294 <4>CPU0T0:1332880,T1:888576,D:10,S:444294,C:1332883 <4>cpu: 1, clocks: 1332883, slice: 444294 <4>CPU1T0:1332880,T1:444288,D:4,S:444294,C:1332883 <4>checking TSC synchronization across CPUs: passed. <4>Setting commenced=1, go go go <4>mtrr: your CPUs had inconsistent variable MTRR settings <4>mtrr: probably your BIOS does not setup all CPUs <4>PCI: PCI BIOS revision 2.10 entry at 0xfb4a0, last bus=1 <4>PCI: Using configuration type 1 <4>PCI: Probing PCI hardware <3>Unknown bridge resource 0: assuming transparent <6>PCI: Using IRQ router VIA [1106/0686] at 00:07.0 <6>PCI->APIC IRQ transform: (B0,I7,P3) -> 5 <6>PCI->APIC IRQ transform: (B0,I7,P3) -> 5 <6>PCI->APIC IRQ transform: (B0,I8,P0) -> 11 <6>PCI->APIC IRQ transform: (B0,I9,P0) -> 10 <6>PCI->APIC IRQ transform: (B0,I11,P0) -> 12 <6>PCI->APIC IRQ transform: (B1,I0,P0) -> 12 <3>PCI: Cannot allocate resource region 1 of device 00:08.0 <4> got res[60000000:600000ff] for resource 1 of PCI device 10ec:8139 ............................ Die Bios Version ist mittlerweile ohne Veränderung 1.05 Hat jemand zufällig ein Tyan 230 das vernünftig läuft? Falls ja , wäre es nett wenn er mir eine kurze Mail schickt. Vielen Dank Achim Zschaege