Hello community, here is the log from the commit of package raspberrypi-firmware for openSUSE:Factory checked in at 2016-09-13 22:24:30 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Comparing /work/SRC/openSUSE:Factory/raspberrypi-firmware (Old) and /work/SRC/openSUSE:Factory/.raspberrypi-firmware.new (New) ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Package is "raspberrypi-firmware" Changes: -------- --- /work/SRC/openSUSE:Factory/raspberrypi-firmware/raspberrypi-firmware-config-rpi.changes 2016-09-05 21:24:40.000000000 +0200 +++ /work/SRC/openSUSE:Factory/.raspberrypi-firmware.new/raspberrypi-firmware-config-rpi.changes 2016-09-13 22:25:15.000000000 +0200 @@ -1,0 +2,15 @@ +Mon Sep 12 13:30:41 UTC 2016 - afaerber@suse.de + +- Clean up config-{rpi2,rpi3}.txt, dropping rpi1 defaults +* On the rpi1 Model B rev. 2 performance results are similar + with and without defaults, so in doubt leave our settings in + config-rpi.txt until proven the defaults work better somewhere. + +------------------------------------------------------------------- +Tue Sep 6 08:33:28 UTC 2016 - fvogt@suse.com + +- Use default frequencies in config-rpi{2,3}.txt (bsc#989511) +* Defaults work well on rpi2 +* Allow much higher frequencies on rpi3 + +------------------------------------------------------------------- raspberrypi-firmware-config-rpi2.changes: same change raspberrypi-firmware-config-rpi3.changes: same change raspberrypi-firmware.changes: same change ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Other differences: ------------------ raspberrypi-firmware-config-rpi2.spec: same change raspberrypi-firmware-config-rpi3.spec: same change raspberrypi-firmware.spec: same change ++++++ config-rpi2.txt ++++++ --- /var/tmp/diff_new_pack.9eTvTz/_old 2016-09-13 22:25:17.000000000 +0200 +++ /var/tmp/diff_new_pack.9eTvTz/_new 2016-09-13 22:25:17.000000000 +0200 @@ -12,12 +12,6 @@ force_turbo=0 # Start in turbo mode for 30 seconds or until cpufreq sets a frequency initial_turbo=30 -# Max ARM freq (default 700 MHz) -arm_freq=840 -# Max core (GPU) freq (default 250 MHz) -core_freq=375 -# SDRAM freq (default 400) -sdram_freq=400 # DO NOT overvoltage manually to not void warranty! over_voltage=0 ++++++ config-rpi3.txt ++++++ --- /var/tmp/diff_new_pack.9eTvTz/_old 2016-09-13 22:25:17.000000000 +0200 +++ /var/tmp/diff_new_pack.9eTvTz/_new 2016-09-13 22:25:17.000000000 +0200 @@ -12,12 +12,6 @@ force_turbo=0 # Start in turbo mode for 30 seconds or until cpufreq sets a frequency initial_turbo=30 -# Max ARM freq (default 700 MHz) -arm_freq=840 -# Max core (GPU) freq (default 250 MHz) -core_freq=375 -# SDRAM freq (default 400) -sdram_freq=400 # DO NOT overvoltage manually to not void warranty! over_voltage=0 # Boot in AArch64 (64-bit) mode