https://bugzilla.novell.com/show_bug.cgi?id=256212 ------- Comment #2 from jimomura@pathcom.com 2007-03-20 19:22 MST ------- The following are the original settings in the "sensors.conf" file, which resulted in the output that I posted previously: # Start of Original Settings: # Winbond W83627EHF configuration originally contributed by Leon Moonen # This is for an Asus P5P800, voltages for A8V-E SE. chip "w83627ehf-*" label in0 "VCore" label in2 "AVCC" label in3 "3VCC" label in7 "VSB" label in8 "VBAT" # +12V is in1 and +5V is in6 as recommended by datasheet compute in1 @*(1+(56/10)), @/(1+(56/10)) compute in6 @*(1+(22/10)), @/(1+(22/10)) # set in1_min 12.0*0.9 # set in1_max 12.0*1.1 # set in6_min 5.0*0.95 # set in6_max 5.0*1.05 # Set the 3.3V # set in2_min 3.3*0.95 # set in2_max 3.3*1.05 # set in3_min 3.3*0.95 # set in3_max 3.3*1.05 # set in7_min 3.3*0.95 # set in7_max 3.3*1.05 # set in8_min 3.3*0.95 # set in8_max 3.3*1.05 # Fans label fan1 "Case Fan" label fan2 "CPU Fan" label fan3 "Aux Fan" # ignore fan3 # ignore fan4 # set fan1_min 1200 # set fan2_min 1700 # Temperatures label temp1 "Sys Temp" label temp2 "CPU Temp" label temp3 "AUX Temp" # ignore temp3 # set temp1_over 45 # set temp1_hyst 40 # set temp2_over 45 # set temp2_hyst 40 # End of Original Settings -- The following is the list of entries I am using now. The changes are just get rid of the "Alarms" and are NOT based on actual specifications for the hardware: # Winbond W83627EHF configuration originally contributed by Leon Moonen # This is for an Asus P5P800, voltages for A8V-E SE. # Edited for MSI-K9A Platinum Jim O. 2007-03-20 chip "w83627ehf-*" label in0 "VCore" label in1 "unknown" label in2 "AVCC" label in3 "3VCC" label in7 "VSB" label in8 "VBAT" # +12V is in1 and +5V is in6 as recommended by datasheet # compute in1 @*(1+(56/10)), @/(1+(56/10)) # compute in6 @*(1+(22/10)), @/(1+(22/10)) set in1_min 1.8*0.9 set in1_max 1.8*1.1 # set in6_min 5.0*0.95 # set in6_max 5.0*1.05 # Set the 3.3V # set in2_min 3.3*0.95 # set in2_max 3.3*1.05 set in3_min 3.3*0.95 set in3_max 3.3*1.05 # Jim O Inputs 4-6 & 9 are unknown. I am just setting them to ranges that kill the alarm set in4_min 1.6*0.95 set in4_max 1.6*1.05 set in5_min 1.45*0.95 set in5_max 1.45*1.05 set in6_min 1.45*0.95 set in6_max 1.45*1.05 set in9_min 1.64*0.95 set in9_max 1.64*1.05 # Following were commented out. Appear to be correct, so I re-instated them. set in7_min 3.3*0.95 set in7_max 3.3*1.05 set in8_min 3.3*0.95 set in8_max 3.3*1.05 # Fans label fan1 "Case Fan" label fan2 "CPU Fan" label fan3 "Aux Fan" # ignore fan3 # ignore fan4 # set fan1_min 1200 # set fan2_min 1700 set fan3_min 00 # Temperatures label temp1 "Sys Temp" label temp2 "CPU Temp" label temp3 "AUX Temp" # ignore temp3 set temp1_over 45 # I changed hyst from 40 to 75 -- JO set temp1_hyst 75 # set temp2_over 45 # set temp2_hyst 40 # End of MSI K9A Platinum -- The following is the output from "sensors": w83627ehf-isa-0a10 Adapter: ISA adapter VCore: +1.36 V (min = +0.00 V, max = +1.74 V) unknown: +1.86 V (min = +1.62 V, max = +1.98 V) AVCC: +3.33 V (min = +1.30 V, max = +4.08 V) 3VCC: +3.33 V (min = +3.14 V, max = +3.47 V) in4: +1.62 V (min = +1.52 V, max = +1.68 V) in5: +1.45 V (min = +1.38 V, max = +1.52 V) in6: +1.45 V (min = +1.38 V, max = +1.52 V) VSB: +3.33 V (min = +3.14 V, max = +3.47 V) VBAT: +3.30 V (min = +3.14 V, max = +3.47 V) in9: +1.65 V (min = +1.56 V, max = +1.72 V) Case Fan: 2083 RPM (min = 907 RPM, div = 8) CPU Fan: 2311 RPM (min = 883 RPM, div = 8) Aux Fan: 0 RPM (min = 0 RPM, div = 16) fan4: 0 RPM (min = 0 RPM, div = 16) Sys Temp: +40°C (high = +45°C, hyst = +75°C) CPU Temp: +39.0°C (high = +80.0°C, hyst = +75.0°C) AUX Temp: +39.0°C (high = +80.0°C, hyst = +75.0°C) Note that the readings from the sensors should not have been affected by the changes that I made to the parameters, but now there are no 12V or 5V readings. Again, I can only conclude that there is some kind of data "TYPE" or "CAST" error somewhere. I have not yet checked the "lm-sensors" website yet. I might not get a chance to do so for the next few days. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug, or are watching someone who is.